• 한국정밀공학회지
• /
• 제29권12호
• /
• pp.1267-1271
• /
• 2012

Demand for optical glass device used for lighting could increase rapidly because of LED lighting market growth. The optical glass devices that have been formed by hot press molding process the desired optical performance without being subjected to mechanical processing such as curve generation or grinding. EL-Max material has been used for many engineering applications because of their high wear resistance, high compressive strength, corrosion resistant and very good dimensional stability. EL-Max is very useful for a glass lens mold especially at high temperature and pressure. The performance and reliability of optical components are strongly influenced by the surface damage of EL-Max during grinding process. Therefore, the severe process condition optimization shall be necessary for the highly qualified EL-Max glass lens mold. To get the required qualified surface of EL-Max, the selection of type of the diamond wheel is also important. In this paper, we report best grinding conditions of ultra-precision grinding machining. The grinding machining results of the form accuracy and surface roughness have been analyzed by using Form Talysurf and NanoScan.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.533-537
• /
• 2003

Compared to sintered polycrystalline diamond (PCD), the deposited thin film diamond has a great advantage on the fabrication of cutting tools with complex geometries such as drills. Because of high performance in high speed machining non-ferrous difficult-to-cut materials in the field of automobiles industry, aeronautics and astronautics industry, diamond-coated drills find large potentialities in commercial applications. However, the poor adhesion of the diamond film on the substrate and high surface roughness of the drill flute adversely affect the tool lift and machining quality and they become the main technical barriers for the successful development and commercialization of diamond-coated drills. In this paper, diamond thin films were deposited on the commercial WC-Co based drills by the electron aided hot filament chemical vapor deposition (EACVD). A new multiple coating technology based on changing gas pressure in different process stages was developed. The large triangular faceted diamond grains may have great contribution to the adhesive strength between the film and the substrate, and the overlapping ball like blocks consisted of nanometer sized diamond crystals may contribute much to the very low roughness of diamond film. Adhesive strength and quality of diamond film were evaluated by scanning electron microscope (SEM), atomic force microscope (AFM), Raman spectrum and drilling experiments. The ring-block tribological experiments were also conducted and the results revealed that the friction coefficient increased with the surface roughness of the diamond film. From a practical viewpoint, the cutting performances of diamond-coated drills were studied by drilling the SiC particles reinforced aluminum-matrix composite. The good adhesive strength and low surface roughness of flute were proved to be beneficial to the good chip evacuation and the decrease of thrust and consequently led to a prolonged tool lift and an improved machining quality. The wear mechanism of diamond-coated drills is the abrasive mechanical attrition.

• 소성∙가공
• /
• 제23권2호
• /
• pp.95-102
• /
• 2014

The under-drive brake piston is an important component in automotive transmissions. It changes the velocity by controlling the gear ratio. It has been traditionally manufactured by hot forging. Recently, there has been an effort to replace this traditional manufacturing method with cold forging in order to improve the dimensional accuracy and decrease the surface roughness. Cold forging uses a smaller amount of initial material and also has a shorter cycle time since the forged surface can be the final surface without the need of post-processing such as machining or grinding. In the current study, finite element analysis was conducted to evaluate a process design using an initial plate with reduced thickness. This smaller thickness decreases the amount of material needed for the part as well as the machining to produce the final product.

• Journal of Mechanical Science and Technology
• /
• 제17권10호
• /
• pp.1475-1484
• /
• 2003

The EDM processing characteristics of one of the nickel-based heat resistant alloys, Hastelloy- X, were investigated under the various EDM conditions and analyzed in terms of surface integrity. This alloy is commonly used as a material for the hot gas path component of gas turbines and it is difficult to machine by conventional machining methods. The primary EDM parameter which was varied in this study were the pulse-on time. Since the pulse-on time is one of the main factors that determines the intensity of the electrical discharge energy, it was expected that the machining ratio and the surface integrity of the specimens would be proportionally dependent on the pulse-on duration. However, experimental results showed that MRR (material removal rate) and EWR (electrode wear rate) behaved nonlinearly with respect to the pulse duration, whereas the morphological and metallurgical features showed rather a constant trend of change by the pulse duration. In addition the heat treating process affected the recast layer and HAZ to be recrystallized but softening occurred in recast layer only. A metallurgical evaluation of the microstructure for the altered material zone was also conducted.

• 한국추진공학회지
• /
• 제4권2호
• /
• pp.46-53
• /
• 2000

알루미늄 제품은 열간단조하면 재료가 연화되어 있어 절삭가공시 연속적인 칩이 발생하여 공구와 피삭재를 감고 회전함으로서 가공면 손상, 공구파손 및 작업자의 안전을 초래함에 따라 가공이 어려워 단지 절삭성 개선목적만을 위해 중간공정으로 T-4열처리하여 절삭가공하고 다시 어닐링처리하여 냉간성형을 하고 최종열처 리를 한다. 따라서 본 연구는 열간단조후 제품을 급냉시키면 용체화처리의 효과를 얻어 재료가 경화됨으로서 절삭성이 개선될 수 있다는 이론에 근거하여 T4열처리를 대체할 수 있는 후처리방법에 대해 연구하였다. 최적의 후처리방법을 구하기 위해 열간단조후 수냉과 공냉처리를 비교분석하였고, 열간단조후 냉각처리까지 지연된 시간과 수냉과정에서의 유지시간에 따른 분식을 통해 최적의 작업조건을 설정하였다.

• Journal of Welding and Joining
• /
• 제6권1호
• /
• pp.35-45
• /
• 1988

오-스테나이트계 스테인레스강에 대한 용접은 용접재료의 개발과 더불어 각종 산업계에 널리 이용되고 있으며 최근 Type 303 오-스테나이트계 스테인레스강 등은 free machining재로써 널리 응용되고 있다. 그러나 이 303계는 피삭성, 절삭성, 칩형성개선을 위한 특수원소(Se, S 등)의 첨가 때문에 용접성에 문제점을 제기하고 있다. 본 연구에서는 Type 303을 중심으로 AISI 304-316NG 및 347NG계의 오-스테나이트계 스테인레스강의 고온연성거동과 고온균열감수성(용접성)에 관한 연구에 대한 검토중 고온연성거동에 관하여 조사하였다. 고온연성평가는 Gleeble Simulator에 의하여 재료와 방향성에 따라 검토하였으며, 그 결과 모든 재료는 압연방향을 종방으로 시험하였을 때는 거의 유사한 고온연성을 나타내었으나 횡방향으로 시험하였을 때는 종방향에 비하여 연성저하를 나타내었다. 이와 같은 고온연성은 후속연구에서 검토될 고온균열 감수성과 밀접한 관련성에 의하여 용접성을 평가할 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.806-809
• /
• 2000

The factors which can improve tool life in machining are consisted of tool geometries, tool materials, coating methods. cutting environments, cutting conditions and so on. Cutting speed in cutting conditions is one of the important factors which can directly influence on the tool life. This paper deals the machinability which is concerned about the cutting direction and the tilt angle of fret form surface in hot die steel(STD I I). The NC datum were analysrd and the effective tool diameters were calculated according to the change of tilt angle the program which can continue the cutting speed with the change of spindle revolution is developed.

• 소성∙가공
• /
• 제11권5호
• /
• pp.388-393
• /
• 2002

Heat-treatment-free steels have been replacing for conventional quenched-and-tempered structural steels since the microalloyed forging steel was developed in early 1970s in Germany. Substantial cost reduction provides the driving force for this change. As a result of intensive R & D efforts and application trials, various kinds of grades, for example heat-treatment-free steels for hot forging, machining and cold heading, have been developed and moreover these steels are in tonnage production throughout the world. The developments in alloy steels, processing conditions and structure-property characteristics of the heat-treatment-free steels, are described and also recent trend and future prospect are summarized in this report.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.139-142
• /
• 2007

This study focuses on the manufacturing process of a magnesium alloy impeller used for the fuel cell car using the hot forging technology. The impeller has the very complicated shape with sharply curved blade and thus generally produced by mechanical machining or casting process. However, since these technologies give the high manufacturing cost or poor mechanical properties, the forging technology is required to make the high-quality impeller with the lower manufacturing cost. In order for production of the impeller by forging technology, the parametric studies using finite element analyses were carried out to find the optimal perform shape of impeller made of magnesium alloy AZ 31 and finally die design was proposed based on the simulation results.

• 한국세라믹학회지
• /
• 제49권4호
• /
• pp.342-346
• /
• 2012

This work deals with the preparation of dense SiC based ceramics with high electrical conductivity without oxide sintering additives. SiC samples with different content of conductive Ti-NbC phase were hot pressed at $1850^{\circ}C$ for 1 h in Ar atmosphere under mechanical pressure of 30 MPa. The conductive phase is a mixture of Ti-NbC in weight ratio of Ti/NbC 1:4. Composite with 50% of conductive Ti-NbC phase showed the highest electrical conductivity of $30.6{\times}10^3\;S{\cdot}m^{-1}$, while the good mechanical properties of SiC matrix were preserved (fracture toughness 4.5 $MPa{\cdot}m^{1/2}$ and Vickers hardness 18.7 GPa). The obtained results show that use of NbC and Ti as sintering and also electrically conductive additives is appropriate for the preparation of SiC-based composite with sufficient electrical conductivity for electric discharge machining.