• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.146-152
• /
• 2018

In this study, to improve the performance of asphalt mixtures for plastic deformation occurring mainly in Korea, complex modifiers were prepared by mixing powders and liquid type modifiers. The main constituents were powdery diatomaceous earth, mica and carbon black, and liquid type solid 70% SBR latex. The tensile strength ratios for the two asphalt mixtures used in the test were above 0.80 for the Ministry of Land Transportation (2017) asphalt mixture production and construction guidelines. The effects of increasing the tensile strength in the dry state was more than 14% when the composite modifier was added. The deformation rate per minute by the wheel tracking test load was an average of 0.07 to 0.147 for each mixture. The strain rate per minute was improved by the modifier, and the dynamic stability was improved by almost 100% from 295 to 590. In addition, the final settling was reduced from 11.38 mm to 9.57 mm. A plastic deformation test using the triaxial compression test showed that the amount of deformation entering the plastic deformation failure zone at the end of the second stage section and in the third stage plastic deformation section was 1.76 mm for the conventional mixture and 1.50 mm for the complex modifier mixture. The average slope of the complex modifier asphalt mixture mixed with the multi-functional modifier was 0.005 mm/sec. The plastic deformation rate is relatively small in the section where the road pavement exhibits stable common performance, i.e. the traffic load.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.2
• /
• pp.97-104
• /
• 2015

The pollution of particulate matter (PM) is considered one of the hot socioenvironmental issues at present time. In this study, we investigated the distribution of fine particulate matter ($PM_{2.5}$) in Wangsimni commercial areas in Seoul, Korea to learn more about its environmental behavior in an urban area. Our analysis of $PM_{2.5}$ was made to distinguish the $PM_{2.5}$ pollution levels between three different types of site characteristics: (1) densely populated area, (2) thinly populated area, and (3) traffic roadside. Moreover, to assess the temporal trends in our study, the concentration levels of $PM_{2.5}$ were also compared between weekdays and weekends and between early in the afternoon and evening. The average concentration of $PM_{2.5}$ from densely and thinly populated areas were measured as $36.0{\pm}13.1$ and $32.3{\pm}11.2{\mu}g/m^3$, respectively. If the results are compared between different time bands, there were apparent differences between weekdays ($29.6{\pm}10.8{\mu}g/m^3$) and weekends ($36.9{\pm}12.1{\mu}g/m^3$). Such difference was also evident between noon ($27.8{\pm}5.8{\mu}g/m^3$) and evening ($38.3{\pm}13.7{\mu}g/m^3$). According to our research, concentration of $PM_{2.5}$ in the study area was affected more sensitively by time zone rather than the population density. The measurement data was also analyzed by drawing concentration map of $PM_{2.5}$ in the Wangsimni commercial areas based on data contouring method.

• Journal of Bio-Environment Control
• /
• v.12 no.4
• /
• pp.200-206
• /
• 2003

Pleurotus eryngii(King oyster) is one of the most promising mushrooms produced on the domestic farms. The quality as well as quantity of Eryngii is sensitively affected by micro climate factors such as temperature, relative humidity, $CO_2$ concentration, and light intensity. To safely produce high-quality Eryngii all the year round, it is required that the environmental factors be carefully controlled by well designed structures equipped with various facilities and control systems. At the commercial mushroom cultivation house(A,B), this study was carried out to find out reasonable range of each environmental factor and yield together with economic and safe structures influencing on the optimal productivity of Eryngii. this experiment was conducted for about two-month from Nov. 11, 2002 to Dec. 30, 2002 in Eryngii. cultivation house-A, B. Ambient temperature during the experiment period was not predominantly different from that of a normal year. The capacity of the hot water boiler and the piping systems were not enough. Maximum air temperature difference between the upper and lower growth stage during a heating time zone was about 2~3$^{\circ}C$. The max. and min. relative humidity were ranged approximately 60~100%, and average relative humidity was ranged approximately 80~100%. And $CO_2$concentration increased until maximum 1,600~1,800 ppm with the passing growing period. The illuminance in cultivation house was widely distributed from 20lx to 160 lx in accordance with position, and it was maintained lower than the recommended illuminance range 100~200 lx. The average yield per bottle was about 67~85g. But the optimal productivity will be evaluated by considering the quality and quantity of mushroom production, energy requirements, facility construction and management cost, etc.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.5
• /
• pp.749-754
• /
• 2017

Objective: The objective of the present study was to investigate the effects of farrowing month (FM), parity and sex on the growth performance of Berkshire swine raised in alternative production systems. Methods: A total of 40 farrowing records from 27 sows and 1,258 body weight (BW) records from 274 piglets collected over a two-year period were used for the analysis. The BWs were recorded at birth, weaning (28 d), 56, 84, 112, and 140 days. Any BW not recorded on schedule was recalculated to conform the days of age among corresponding BW records, using growth curves drawn with polynomial functions whose power was determined by the number of existing observations for each individual. Results: The mean parity (${\pm}$standard deviation) of the sows was $3.42{\pm}2.14$. The sows that farrowed in June had the lowest number of total born with an average of $6.25{\pm}2.22$ piglets per sow. However, the lowest average number of piglets weaned at day 28 was found in sows that farrowed in May, as well as the highest number recorded for the stillborn piglets with an average of 2.67 piglets per sow. Moreover, the smallest increase in weight from birth to weaning occurred in piglets that were farrowed in May, which also corresponds with the average daily gain (ADG) of 0.29 kg and the last recorded weight measurement on day 140 of $41.69{\pm}1.45kg$. Contrastingly, the highest growth rate was found among pigs farrowed in June, with the largest increase in weight of 7.55 kg from birth to weaning, the highest ADG of 0.51 kg from birth to 140 day of age and the highest BW of $74.70{\pm}1.86kg$ recorded on day 140. Conclusion: Pigs farrowed in June also had the least number of piglets that died between birth and weaning. The zone of thermal comfort found in sows reared in indoor confinement systems did not improve the reproductive performance of the sows reared in an outdoor, alternative production system, while the growth performance of the piglets was improved when the ambient temperature was consistently hot or consistently cold.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1137-1143
• /
• 2010

This paper presents a fatigue design method for plug- and ring-type gas-welded joints, which takes into account the effects of welding residual stress. To develop this method, we simulated the gas-welding process by performing nonlinear finite element analysis (FEA) To validate the FEA results, numerically calculated residual stresses in the gas welds were then compared with experimental results obtained by the hole-drilling method. To evaluate the fatigue strength of plug- and ring-type gas-welded joints influenced by welding residual stresses, the use of stress amplitude $(\sigma_a)_R$, which includes the welding residual stress in gas welds, is proposed $(\sigma_a)_R$ on the basis of a modified Goodman equation that includes the residual stress effects. Using the stress amplitude $(\sigma_a)_R$ at the hot spot point of gas weld, the relations obtained as the fatigue test results for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged to obtain the $(\sigma_a)_R-N_f$ relationship. It was found that more systematic and accurate evaluation of the fatigue strength of plug- and ring-type gas-welded joints can be achieved by using $(\sigma_a)_R$.

• Journal of Korean Society of Forest Science
• /
• v.65 no.1
• /
• pp.31-42
• /
• 1984

This study contains the scientific justification of the forest aromatic bath(F.A.B) in the stage of introduction and the general concepts using in the design of the forest aromatic bath ground, especially definition of F.A.B, basic activities and facilities, carrying capacity and criteria deserving much consideration in designing of it. Terpene, the origin of F.A.B appearance, is made clear that it is efficacious in our physical health. The forest (coniferous one) mainly exhales terpene about noon and morning and seasonally spring and summer time. The most influential factor to exhale terpene is the climate one-wind, temperature, sunlight, humidity. Forest canopy and leaves are related to the concentration of terpene in the forest area. The basic activities for F.A.B are mostly static, and so are the facilities. The forest aromatic bath room(F.A.B.R) which a person must be given for F.A.B. is $169m^2$, 59 persons per ha. This $169m^2$ is the carrying capacity of F.A.B. The sites of F.A.B.G. might better be located around the national and provincial park, mountain torrent, hot spring zone and the waterfronts. Meanwhile, forest management in F.A.B.G should be enforce in order to keep on constantly maintaining the exhalation quantity of terpene.

• Applied Chemistry for Engineering
• /
• v.20 no.6
• /
• pp.638-645
• /
• 2009

High alumina refractory used in a coal gasifier was analyzed and the degradation mechanism by molten slag was investigated. The depth of refractory severely damaged by slag varied between 12~40 mm, including the adhered slag layer. The sample also showed the cracks formed in parallel to the slag/refractory interface. The degree of degradation varied with the micro-structures in the refractory. Fused alumina grains showed the uneven boundary and pore formation just along the edges, while the tablet alumina showed the slag penetrated between sintered alumina around which the formation of Al-Fe phase was observed. Calcium aluminate cements were not observed at the high temperature zone near the slag/refractory interface, probably due to dissolution into molten slag. Around large grains of alumina, rod shape alumina, which appeared to be recrystallized during cooling, were observed, and large pores were also formed around those grains. Therefore, in high alumina refractories, hot molten slag dissolves the bonding phase and rod-shape alumina phase is recrystallized upon cooling. During this process, cracks are developed due to structural change, and the degradation occurs by physical causes such as structural spalling.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.377-384
• /
• 2010

Many routes have been developed for the synthesis of signle-walled carbon nanotubes (SWCNTs). We spun fibers of SWCNTs directly from vertical furnace using a liquid source of carbon and an iron-contained molecule. The solution was prepared by ethanol as a carbon source, in which ferrocene as a catalyst, thiophene were dissolved. It was then injected from the top of the furnace into hot zone with hydrogen as a carrier gas. We successfully synthesized high-quality SWCNTs by adjusting the various experimental conditions, such as concentration of ferrocene, solution injection rate, concentration of thiophene, and hydrogen flow rate. Measurement of Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy were carried out to find the optimized conditions. The synthesized SWCNTs (1.16~1.64 nm) appeared a bundle structure and well-aligned parallel to the direction of furnace. These results also provide an simple way for high-quality SWCNTs mass production and fabricating direct spining SWCNTs fiber. It will allow one-step production of SWCNTs fiber with potentially excellent properties and wide-range applications.

• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Korean Journal of Environment and Ecology
• /
• v.25 no.4
• /
• pp.562-572
• /
• 2011

This study is to examine the environmental characteristics of subpopulations of Ilex crenata var. microphyllla Max. distributed in the east-west slopes of Mt. Halla National Park based on analyzing the factors of environment, vegetation and soil. The result of the TWINSAPN analysis conducted on 56 study plots between the altitudes of 500 m and 1600 m of east-west slopes of Mt. Halla National Park can be divided into five communities-Prunus maximowiczii Rupr., Manshurian fullmoon Maple, Carpinus tschonoskii Max., Daphniphyllum macropodum Miq., Quercus serrata Thunb. ex Murray and Pinus thunbergil Parl. Among these communities, the plot with high importance percentage of the subpopulation of Ilex crenata var. microphyllla Max., is the Carpinus tschonoskii Max.-Daphniphyllum macropodum Miq. included in the altitude of 600m~1200m radius. The dominant species of the upper shrub layer was Carpinus tschonoskii Max.(I.P.: 29.82%) while the dominant species of the canopy layer was Daphniphyllum macropodum Miq.(I.P.: 26.76%). For the understory layer the dominant species was Ilex crenata var. microphyllla Max.. Species diversity index was on the low end with 0.7424, indicating the stably formed climax community of Carpinus tschonoskii Max.. The analysis of soil properties showed high concentrations of organic matters, available phosphate and Ca, Mg, the high importance percentage of the of Ilex crenata var. microphyllla Max. is found in altitude of 600m~800m on the eastern slope and the altitude of 800m~1,000m radius on the west slope. This region is included in the southern part of the cold/hot forest zone, its high importance percentage of Carpinus tschonoskii Max. and low in the species diversity index of 0.7424, and has formed stable climax community of Carpinus tschonoskii Max. in Mt. Halla.