• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.184-187
• /
• 2003

The simulation program is developed to get the target strip crown of high strength steel in the continuous hot strip rolling. The developed program consists of several sub-program, which contains work roll shifting pattern, roll wear profile, roll thermal expanded profile and strip profile. Also, the variation of strip profile is investigated according to roll deflection and flattening. The results are compared with the values observed from the actual hot rolling of high strength steel. And effect of bender force on the strip profile is studied. The strip crown is shown to decrease with increasing bender force.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.115-118
• /
• 1997

Recently, hot rolling oil lubrication technology is required to face with the new environments such as the rapid introduction of high wear resistent high speed steel roll the development of continuous hot rolling technology. In the hot strip mill, according to rolling and quality required conditions are constrict, Roll material of hot rolling finishing stand is changing Hi-Cr Roll to High Speed Steel [HSS] Roll. The problem of HSS Roll of roll force and strip scale defects are increasing in hot strip mill, So we have tested HSS Roll in hot rolling simulator as rolling condition, rolling speed, draft, hot oil concentration. To reduce roll force and prevent scale defects. We get some merit rolling force, rolling torque, roll wear reduction, roll and strip surface roughness and hot rolling critical oil concentration 0.4%. Finally we are going to investigate the effect of hot rolling oil of on rolling with HSS Roll.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.73-76
• /
• 2009

Increase in tensile strength of steel is important for fuel efficiency and $CO_2$ reduction. But the higher the strip strength, the more defect could be generated in hot strip mill. This study focuses on line-type edge scab. One of the causes for the defect is initial edge cracks commonly observed on a slab but their correlation has not been verified yet. Thus, the objective of this report is to verify if the edge crack is exactly the seed for edge scab. For this, we conducted pilot hot rolling test with cracked slab and compared the development of cracks and edge scabs on hot-rolled strip.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.11
• /
• pp.991-997
• /
• 2013

In this paper, we propose a CFWC (CCD and fuzzy PID based width control) scheme to obtain the desired delivery width margin of a vertical rolling mill in hot strip process. A WMS(width measurement system) is composed of two line scan cameras, an edge detection algorithm, a glitch filter, and so on. A dynamic model of the mill is derived from a gauge meter equation in order to design the fuzzy PID controller. The controller is a self-learning structure to select the PID gains from the error and error rate of the width margin. The effectiveness of the proposed CFWC is verified from simulation results under a width disturbance of the entry in the mill. Using a field test, we show that the performance of the width control is improved by the proposed control scheme.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.3
• /
• pp.330-336
• /
• 2009

This paper studies on the new control algorithm for the mass-flow stabilization in strip head part of a hot strip mill. A new strip tension model in the strip head part is derived using the current deviation of two neighboring stands. The current deviation means a difference between a measured current and a lock-on current, where the lock-on current is set up when a strip tension or a looper angle reaches each target value or time is about 0.4sec, respectively. On the basis of the tension calculation model, a mill velocity of a backward stand is controlled to stabilize a strip mass-flow by PI control algorithm. Therefore, the mass-flow control for strip head part is executed from a metal-in time into a foreward stand till the looper works normally. It is known by the results of a computer simulation and an experiment that the proposed control algorithm is very effective in stabilizing the mass flow of the strip head part.

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.200-207
• /
• 1999

To increase dimensional accuracy of strip width, model to compensate width spread during roughing mill has been developed. To measure the amount of width spread during the production rolling more precisely, special roughing rolling procedures for the horizontal rolling and dog-bone rolling were designed in the actual production mill. From the operational data analysis, it is known that the prime factors influencing on the width spread were strip width, strip thickness, edging amount, number of pass and type of edger roll etc., Based upon the statistical analysis of rolling data, new models which can predict width spread during horizontal rolling and dog-bone rolling were developed and tested on the actual processing conditions for the reliability. The application test showed that newly developed model gave fairly accurate predictions on the width spread during roughing passes.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.374-374
• /
• 2000

In this paper, we developed an ANFIS controller through ES algorithm for disturbances rejection in Hot Rolling. The looper of a Hot Rolling is installed between each pair of stands and plays key roles to enhance the product quality of the strip by controlling the tension and the width of the strip. At the same time, the AGC on top of the Mill produces a strip with the desired thickness through pressing its Mill. Between both, however, interactions are caused by coupling effects among strip tension, looper angle and strip thickness. In addition, in case disturbances, it is more difficult to keep strip quantities desirable. So we present an ANFIS controller through ES algorithm which is able to identify fuzzy rule with input/output data and update itself through output errors.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.175.3-175
• /
• 2001

A control system for crop cutting in Hot strip Mill is developed. The development system is composed of three sub-systems. one is crop shape system which captures the shapes of the strip's head and tail using the area CCD camera. Another is Laser Speed System which measures the speed and length of strip. and, the other is control system which controls the optimal cutting length and crop shear motor. As a result, with a developed system we can reduce crop loss considerably.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.614-618
• /
• 2002

In hot strip mills, Portable Roll Scanner (the portable roll surface temperature and profile measuring device) can be used to calibrate on-line Process models for strip crown and flatness by measuring the thermal expansion and wear profile of the rolls. And the surface temperature measurement can be used to optimize the roll cooling system. Portable Roll Scanner consists of the measuring device, which has two contact inductive distance transducers for roll profile measurement and one infrared Pyrometer for surface temperature measurement, and computer-based controller that is equipped with the measuring device. By the wireless data communication, the data is transferred to the memory of notebook for further analysis. After roll extraction from mills, Portable Roll Scanner measure the roll profile and surface temperature simultaneously along the work roll face and display the results in the TFT color monitor of notebook. Portable Roll Scanner is useful at mill-side and roll grinding shop.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.295-300
• /
• 2008

In this paper, a new looper controller is proposed to minimize the tension variation of a strip in the hot strip finishing mill. The proposed control technology is based on a receding horizon control (RHC) to satisfy the constraints on the control input/state variables. The finite terminal weighting matrix is used instead of the terminal equality constraint. The closed loop stability of the RHC for the looper system is analyzed to guarantee the monotonicity of the optimal cost. Furthermore, the RHC is combined with a 4SID(Subspace-based State Space System Identification) model identifier to improve the robustness for the parameter variation and the disturbance of an actuator. As a result, it is shown through a computer simulation that the proposed control scheme satisfies the given constraints on the control inputs and states: roll speed, looper current, unit tension, and looper angle. The control scheme also diminishes the tension variation for the parameter variation and the disturbance as well.