• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.5
• /
• pp.28-33
• /
• 2004

Generally Horn-type rudders have been used for single propeller and single rudder system. The reason is that the rudder torques of Horn-type rudder are smaller than those of Spade rudder with same lift force. But it is found that the rudder cavitation occurs on a Horn-type rudder of fast container ship. In this paper the comparison results of Horn-type and Spade rudders are described. HPMM tests are carried out to compare the effects of two rudder types on the maneuverability of a ship. It is shown that the maneuvering performance of a ship equipped with Horn-type rudder is better than that equipped with Spade rudder by comparing the test results and maneuvering coefficients at scantling condition. The reason is that the movable part area of Horn-type rudder is about 14％ larger than that of Spade rudder with same total area. And the rudder torque of Spade rudder is greater than that of Horn rudder. At ballast condition, however, the effect of rudder type is negligible.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2006.09a
• /
• pp.77-80
• /
• 2006

In recent booming up of the ship building market, the supplying of large scale casting is difficult to keep the delivery schedule for ship yard because of the restrict manufacturer in Korea. And also, it is main cause to rise-up the cost of castings. This paper describes the outline of guidance of optimizing design for Rudder Horn Casting to reduce the risk of the delivery problem to ship yard.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.4 no.1
• /
• pp.70-74
• /
• 2001

In this paper, we studied the maneuvering performances of a ship with flapped rudder. PMM tests were carried out for a ship model with horn type rudder or flapped rudder. The Abkowitz's model was used as a basic mathematical model to simulate the maneuvering motions. The maneuvering motions of a ship with flapped rudder were compared with those of a ship with horn-type rudder. As a result, it was found that the turning ability of a ship with flapped rudder was remarkably improved.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.2
• /
• pp.1-10
• /
• 2002

Hull-propeller-rudder interactions are studied by the iterative computational procedures. Hull effects on the propeller are reflected through the effective velocities computed by the vortex ring method which used the measured nominal wake as input data. A potential based panel method has been developed to solve the propeller-rudder interactions using the obtained effective velocities. Steady flow characteristics around the rudder surface can be obtained by computing the induced velocities on the rudder by the propeller and vice versa are computed by the iterative manner until the converged solutions are obtained. Flow characteristics around the propeller and the rudder are measured by Laser Doppler Velocimetry(L.D.V.) in large cavitation tunnel at Samsung Heavy industries. The gap flow model is adopted to solve the characteristics of the horn rudder. Numerical results are compared with the experimental values and the computed velocity fields and pressure distributions with rudder angle on the horn rudder surface show good agreement with measured ones in large cavitation tunnel.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.2 s.152
• /
• pp.101-110
• /
• 2007

Recently, rudder erosion due to cavitation frequently has occurred at large high speed container carriers. Especially, in the case of a horn-type rudder, the rudder erosion is severe around a gap. The gap-flow characteristics are investigated through a computational method to understand the effects of a gap on the cavitation and rudder efficiency. A viscous flow theory utilizing a cavitation model is applied to calculate the flow around idealized 2-dimensional rudder sections in a full scale. The effects of gap clearance and flow-control projection are also investigated. From the computational results, the mass flow rate through a gap is found to be one of the important parameters to affect the cavitation and rudder efficiency.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.27-31
• /
• 1990

To calculate the lift of a thin lifting surface like the ship-rudder, it is popular to replace the lifting surface by a series of vortices. Two methods, which are vortex lattice method and mode function method, are frequently used to distribute the vortices on the lifting surface. In this paper, the intermediate way of two mentioned calculation method is carried out to exploit the merits of them. The basic concept of this method is to divide the lifting surface with several strips in span-wise and replace vortices to the chord-wise at each strips. A horn type semi-balanced rudder is chosen for the real method, and the validity of the proposed calculation is pursued by the open water test of the same rudder. Finall, this method is applied to the calculation of the interference between the two homogenous rudders siting parallel to the free stream.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.3 s.153
• /
• pp.228-237
• /
• 2007

The flow characteristics around a horn-type rudder behind an operating propeller of a high-speed large container carrier are studied through a numerical method in fully wetted and cavitating flow conditions. The computations are carried out in a small scale ratio of 10.00(gap space=5mm) to consider the gap effects. The Reynolds averaged Navier-Stokes equation for a mixed fluid and vapor transport equation applying cavitation model are solved. The axisymmetry body-force distribution technique is utilized to simulate the flow behind an operating propeller. The gap flow, the three-dimensional flow separation, and the cavitation are the flow characteristics of a horn-type rudder. The pattern of three-dimensional flow separation is analyzed utilizing a topological rule. The various cavity positions predicted by CFD were shown to be very similar to rudder erosion positions in real ship rudder. The effect of a preventing cavitation device, a horizontal guide plate, is also investigated.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2009.09a
• /
• pp.47-51
• /
• 2009

It is well known that a rudder is influential devices to help ship maintain its stable performances, such as a course-keeping and maneuverability. In the procedures of a commercial ship design proper rudder dimensions (area and shape) ensuring better ship maneuverability have been settled in an initial concept design stage performed by a preceding department, without little structural consideration. It is true that there are time discrepancy between an initial design and a structural analysis stage. Therefore structural analysis results would sometimes cause a rudder to modify its dimensions. Most of these cases, however, ship design and performance tests had been finished. In this matter, only limited modifications of redder could be carried out. Besides, these could also cause bad effects on productivity. Finally, it is necessary to develop a new program considering co-relationship between an initial rudder design and a following work, a structural strength analysis, in order to enhance productivity and minimize a rate of redesign procedures.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.4 s.148
• /
• pp.422-430
• /
• 2006

The horn and movable parts around the gap of the conventional semi-spade rudder are visualized by high speed CCD camera with the frame rate of 4000 fps (frame per second) to study the unsteady cavity pattern on the rudder surface and gap. In addition, the pressure measurements are conducted on the rudder surface and inside the gap to find out the characteristics of the flow behavior. The rudder without propeller wake is tested at the range of $1.0{\leq}{\sigma}_v\;1.6$ and at the rudder deflection angle of $-8{\leq}{\theta}{\leq}10^{\circ}$. The time resolved cavity images are captured and show strong cavitation around the rudder gap in all deflection angles. As the deflection angle gets larger, the flow separated from the horn surface increases the strength of cavitation. The accelerated flow along the horn decreases its pressure and the separated flow from the horn increases the pressure abruptly. The pressure distribution inside the gap reveals the flow moving from the pressure to suction side. In the negative deflection angle, the turning area on the movable part initiates the flow separation and cavitation on it.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.11
• /
• pp.924-931
• /
• 2009

The two-dimensional turbulent flow around the horn-type rudder has been examined in the present study by using the commercial code FLUENT. The standard ${\kappa}-{\epsilon}$ model is used as a closure relationship. The geometry of horn rudder is based on the NACA 0020 airfoil. The simulations for various angle attack (${\alpha}$) and yaw angle(${\delta}$) are carried out. The effect of Reynolds number is also investigated in this study. The cavitation is more possible when the yaw angle is $6^{\circ}$ and it is more serious as Reynolds number increases.