• Journal of the Korean Home Economics Association
• /
• v.46 no.9
• /
• pp.137-146
• /
• 2008

This study was conducted in order to spread out lower body 3D scan data of men in their twenties. The aim was to achieve slacks pattern with ease allowance through comparison with existing flat patterns. For conversion of 3D scan data into 20 pattern, reference lines were established by using Rapid Foam in 3D shape analysis software. 2C-AN program and Yuka CAD were used to convert 20 pattern earned with straight posture of 3D scan data into slacks pattern by using Triangle Simplification & Runge-Kutta Method. In order to achieve this we needed to set a line 9cm below the hip line, to array vertex of each block to crease line while maintaining the horizontal line. And then we needed to set ease allowance in back crotch and to set waist circumference or hip circumference ease allowance in side seam of slacks. Results showed that long front crotch length can be achieved if 3D scan data is compared with 20 existing flat pattern. Slacks pattern that raise front crotch by about 1.5cm compared to back crotch and also possess ease allowance in back crotch area are great in appearance evaluation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.830-838
• /
• 2003

In this paper, TX/RX dual operation microstrip single antenna for satellite communication is designed, analyzed, fabricated and measured. TX/RX frequency ranges are 14.0∼l4.5 GHz, 11.7∼12.75 GHz in respectively and vertical and horizontal polarizations are used for TX and RX. This antenna uses microstrip direct feeding for RX and aperture coupled strip-line feeding for TX and accommodates stacked elements for a high directivity and wide impedance bandwidth. In an analysis of single element, FDTD and MOM was compared and FDTD analysis was more accurate because of the consideration of finite structure and imperfect two ground planes. The proposed structure facilitates generally to an extension of two dimensional array and lower an unwanted radiation by strip-line feed in TX. TX/RX 8${\times}$4 array has a return loss below -10 dB, -14 dB in TX, RX respectively and a gain ranging from 19.1∼20.7 dB in TX, 21.2∼21.8 dB in RX which has a radiation efficiency of 43∼5l %, 52∼57 %.

• Economic and Environmental Geology
• /
• v.57 no.1
• /
• pp.17-23
• /
• 2024

Ground penetrating radar (GPR) survey is a geophysical method that utilizes electromagnetic waves reflecting from a boundary where the electromagnetic property changes. As the frequency of the antenna is about 25 MHz ~ 1 GHz, it is effective to acquire high resolution images of underground pipe, artificial structure, underground cavity, and underground structure. In this study, we analyzed the change of signals reflected from the same underground objects according to the arrangement of transceiver antennas used in ground penetrating radar survey. The antenna used in the experiment was 200 MHz, and the survey was performed in the vertical direction across the sewer and the parallel direction along the sewer to the sewer buried under the road, respectively. A total of five antenna array methods were applied to the survey. The most used arrangement is when the transmitting and receiving antennas are all perpendicular to the survey line (PR-BD). The PR-BD arrangement is effective when the object underground is a horizontal reflector with an angle of less than 30°, such as the sewer under investigation. In this case study, it was confirmed that the transmitter and receiver antennas perpendicular to the survey line (PR-BD) are the most effective way to show the underground structure. In addition, in the case where the transmitting and receiving antennas are orthogonal to each other (XPOL), no specific reflected wave was observed in both experiments measured across or parallel to the sewer. Therefore, in the case of detecting undiscovered objects in the underground, the PR-BD array method in which the transmitting and receiving antennas are aligned in the direction perpendicular to the survey line taken as a reference and the XPOL method in which the transmitting and receiving antennas are orthogonal to each other are all used, it can be effective to apply both of the above arrangements after setting the direction to 45° and 135°.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.2 no.1
• /
• pp.89-93
• /
• 2002

This paper introduces a vision-based on-line fabric inspection methodology of woven textile fabrics. Current procedure for determination of fabric defects in the textile industry is performed by human in the off-line stage. The advantage of the on-line inspection system is not only defect detection and identification, but also 벼ality improvement by a feedback control loop to adjust set-points. The proposed inspection system consists of hardware and software components. The hardware components consist of CCD array cameras, a frame grabber and appropriate illumination. The software routines capitalize upon vertical and horizontal scanning algorithms characteristic of a particular deflect. The signal to noise ratio (SNR) calculation based on the results of the wavelet transform is performed to measure any deflects. The defect declaration is carried out employing SNR and scanning methods. Test results from different types of defect and different style of fabric demonstrate the effectiveness of the proposed inspection system.

• Journal of Advanced Navigation Technology
• /
• v.10 no.4
• /
• pp.326-332
• /
• 2006

In this study, the antenna was proposed for the omni-directional characteristic in horizontal plane. Therefore we proposed $1{\times}4$ microstrip patch array on cylindrical surface for studying microstrip patch antennas. This antenna is designed for 2.45GHz ISM band and applications. This antenna can be applied to the base station of wireless microphone and access point of wireless LAN. The length and width of the patch antenna and the width of the feed line were calculated by using the theory of microstrip patch antenna, by using the both the 2.5D and 3D EM simulators the optimized antenna characteristics are obtained. From result of measured, antenna's impedance of coaxial waveguide port was 51.915-j3.688 ${\Omega}$, the return loss was -31dB and VSWR was 1.081.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.144-150
• /
• 2012

In this paper, circularly polarization patch array antenna of RSE(Road-side Equipment) base station for DSRC(Dedicated Short Range Communication) of ITS(Intelligent Transport System) is proposed. The antenna of RSE base station for DSRC is designed to operate circularly polarization to receive reflected signal from multiplex path effectively. The proposed antenna consisted of microstrip patch and feed line, the slit is inserted in the proximity of the slot of feed structure to generate circularly polarization. The $2{\times}2$ array structure is designed to satisfying gain that DSRC RSE base station antenna required. Measured impedance bandwidth and axial-ratio bandwidth are satisfied by all DSRC band of 5.795~5.855 GHz. Vertical and horizontal HPBW of the proposed antenna are both about 43 degrees, it showed gain characteristic of about 11.21 dBi.

• Journal of the Korean Geophysical Society
• /
• v.6 no.3
• /
• pp.155-164
• /
• 2003

The validity and efficiency of the roll-along technique widely used in 2-D electrical resistivity survey are analyzed in case of the dipole-dipole and the Wenner-Schlumberger arrays by numerical modelling. The shallow anomalous resistivity bodies are successfully inverted both in the dipole-dipole and in the Wenner-Schlumberger arrays because the shallow data of pseudosection are not omitted by the roll-along technique. However, the deep anomalous resistivity bodies can not be well resolved due to the skip of observed data which is more significant in the Wenner-Schlumberger array having relatively poor horizontal coverage of obtaining data. Carrying out electrical survey adopting the dipole-dipole array, the skip of data is insignificant because it is unfeasible to expand the electrodes to the maximum electrode separation coefficient($n_max$) owing to low S/N ratio. In case of the Wenner-Schlumberger array, however, because it is generally feasible to expand the electrodes $n_max$ to the owing to high S/N ratio, it is highly possible that skip of data from the roll-along technique causes significant distortion of inversion results. Therefore, adopting the Wenner-Schlumberger array having deeper median depth(Edwards, 1977) than do the dipole-dipole array on condition of the same unit electrode spacing( ($a$) ) and $n_max$, it is recommended to determine $a$ based on not $n_max$but $n_prob$free from the skip of observing data and forward electrodes with keeping overlap interval 3/4 of the survey line length in order to reduce the distortion of resistivity structure and perform resistivity survey efficiently. These results are confirmed by numerical modelling.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.3
• /
• pp.25-32
• /
• 2021

In this paper, the Magneto-Electric(ME) dipole array antenna with dual-polarization in the X-Band is proposed and it is implemented and measured. The proposed array antenna is composed of 32 single ME dipole antenna and a Teflon PCB. 1 × 1 ME dipole antenna is implemented dual-polarization by radiating vertical polarization and horizontal polarization from two pairs of radiators. 2-port feeding structures are realized by lamination process using LTCC. And, each port independently feeds the radiator through a Γ-shaped feeding strip with isolation between ports. The Teflon PCB used in the antenna array has a 4-layer structure, and 2-port is fed through the top and bottom layers. The λ_g/4 transformer is applied to the transmission line of the Teflon PCB for impedance matching of the arrayed antenna and the Teflon PCB, and the optimal parameters are obtained through simulation. The measured maximum antenna gains of port 1 was 18.2 dBi, Cross-pol was 1.0 dBi. And the measured maximum antenna gains of port 1 was 18.1 dBi, Cross-pol was 3.2 dBi.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.117-128
• /
• 2018

In this paper, compact linear dual polarized series-fed $1{\times}2$ linear and $2{\times}2$ planar arrays antennas for airborne SAR applications are proposed. The proposed antenna design consists of a square radiating patch that is placed on top of the substrate, a quarter wave transformer and $50-{\Omega}$ matched transformer. Matching between a radiating patch and the $50-{\Omega}$ microstrip line is accomplished through a direct coupled-feed technique with the help of an impedance inverter (${\lambda}/4$ impedance transformer) placed at both horizontal and vertical planes, in the case of the $2{\times}2$ planar array. The overall size for the prototype-1 and prototype-2 fabricated antennas are $1.9305{\times}0.9652{\times}0.05106{{\lambda}_0}^3$ and $1.9305{\times}1.9305{\times}0.05106{{\lambda}_0}^3$, respectively. The fabricated structure has been tested, and the experimental results are similar to the simulated ones. The CST MWS simulated and vector network analyzer measured reflection coefficient ($S_{11}$) results were compared, and they indicate that the proposed antenna prototype-1 yields the impedance bandwidth >140 MHz (9.56-9.72 GHz) defined by $S_{11}$<-10 dB with 1.43%, and $S_{21}$<-25 dB in the case of prototype-2 (9.58-9.74 GHz, $S_{11}$< -10 dB) >140 MHz for all the individual ports. The surface currents and the E- and H-field distributions were studied for a better understanding of the polarization mechanism. The measured results of the proposed dual polarized antenna were in accordance with the simulated analysis and showed good performance of the S-parameters and radiation patterns (co-pol and cross-pol), gain, efficiency, front-to-back ratio, half-power beam width) at the resonant frequency. With these features and its compact size, the proposed antenna will be suitable for X-band airborne synthetic aperture radar applications.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.350-357
• /
• 2000

Experiments were performed by using PF-5060 and water to investigate the influence of an aspect ratio of a horizontal rectangular channel on the cooling characteristics from an in-line $6{\times}1$ array of discrete heat sources which were flush mounted on the top wall of the channel. The experimental parameters were aspect ratio of rectangular channel, heat flux of simulated VLSI chip, and channel Reynolds number. The chip surface temperatures decreased with the aspect ratio at the first and sixth rows, and decreased more rapidly at a high heat flux than at a low heat flux. The measured friction factors at each aspect ratio for both water and PF-5060 gave a good agreement with the values predicted by the modified Blasius equation within ${\pm}7%$. The Nusselt number increased as the aspect ratio decreased, but the increasing rate of Nusselt number reduced as the aspect ratio decreased. A 5:1 rectangular channel yields the most efficient cooling performance when the heat transfer and pressure drop in the test section were considered simultaneously.