• International Journal of Ocean System Engineering
• /
• 제2권4호
• /
• pp.239-243
• /
• 2012

The cylinder liner of a low speed engine is one of the most important parts of the marine diesel engines used in merchant ships. However, a sufficient degree of precision in the manufacturing method for these cylinder liners has never existed. Conventional honing stones have always been used for machining large marine cylinder liners. Therefore, it is necessary to develop a honing process that optimizes the honing characteristics. In this study, a CBN honing stone was manufactured to improve the honing performance for a cylinder liner and shorten the processing time, and machining experiments on a practical cylinder liner were carried out. Then, a comparison was made between the CBN honing and honing with a conventional GC stone using parameters such as the honing time, machining quantity, and honing cost. As a result, for a #60 CBN stone, the machining amount was significantly improved compared to the conventional one by about $1.1{\mu}m$/min, and in respect to the machining cost, a reduction of about 57% was achieved. However, an improvement in the process with a #800 CBN stone could not be expected because it did not show a significant difference compared to the case of the existing stone. From the above results, if the liner were honed using a CBN honing stone, the rough machining and intermediate processing during an early stage of the honing process were excellent compared to the conventional one. However, we could not find a significant difference in the case of finish honing.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.143-149
• /
• 2000

Grinding technology in morden industry society is focusing on research and development for grinding stone and machin-ing parts for the purpose of high accuracy and high efficiency of products. But in order to equip the high technology and high accuracy of micro stone which is one of grinding stone a continuous effort on R& D is require. In this study the honing processing work of 2 cycle engine cylinder for motorcycle which has an open hole is carried out so as to investigate the boring and hone stone effects on accuracy of honing. As the experimental result of this study we could conclude that it is possible to secure good conditions of honing by controlling and keeping appropriate cycle-time in the stage of boring for the prior step of honing.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.326-331
• /
• 1999

Grinding technology in morden industry society is focusing on research & development for grinding stone and machining parts for the purpose of high accuracy and high efficiency of products. But, in order to equip the high technology and high accuracy of micro stone which is one of grinding stone, hardly and continuous effort on R&D is required.In this study, honing processing work of 2-cycle engine cylinder for motorcycle which has open hole is practiced so as to clear how borning that is prior step of honing and hone stone make an influence on accuracy of honing. As the result of analyzing the results of experiments, we came to conclusion that we can secure good conditions of honing by controlling and keeping appropriate cycle-time in the stage of boring of prior step of honing.

• 한국기계가공학회지
• /
• 제18권4호
• /
• pp.69-75
• /
• 2019

Since gasoline engines are based on a combination of a cast iron liner and an aluminum block, which have different thermal properties and stiffnesses, bore shape distortion is likely to occur during honing due to uneven thermal deformation. To solve this problem, many tests and evaluations are needed to support the development of a high-performance honing stone with low heat generation. Moreover, performance evaluation, which depends on inspection and observation after work, often requires much trial and error to optimize tool design, due to challenges in the accurate interpretation of results. This study confirmed that the assessment of grinding capability was clarified by evaluating performance under severe work conditions and by in-situ measurement and recording of current consumption (workload) and heat generation during operation. As a result of using a honing stone with excellent grinding performance in engine block manufacture-in which cylinder bore distortion caused by thermal deformation during manufacture is a problem-a noticeable improvement in the degree of cylindricity was observed.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.344-347
• /
• 2005

The cylinder liners of low speed engine are one of a important equipment in merchant ship. But, the precision machining method of cylinder liner is not developed sufficiently. This paper shows a new honing method using by CBN honing stones.

• 오토저널
• /
• 제15권2호
• /
• pp.130-143
• /
• 1993

Engineering ceramics have some excellent properties as the material for the mechanical components. It is, however, very difficult to grind ceramics with high efficiency because of their high strength, hardness and brittleness. In this paper, experiments are carried out to obtain the effect of "In-process dressing" to grind the Engineering ceramics with high efficiency. To save running time for dressing process and obtain restraint effect of diamond grain wear, "In-process dressing" system using WA stick type honing stone is proposed. Representative Engineering ceramics, such as AI$_{2}$O$_{3}$, Si$_{3}$N$_{4}$, are ground with diamond wheel. Also bending strength test is carried out to check upward tendancy of mecahnical properties as the result of machining defact restraint through the grinding machining method using "In-process dressing" process. Some results obtained in this study provide useful information to attain the high efficiency grinding and the high mechanical properties of Engineering ceramics.rties of Engineering ceramics.

• 한국정밀공학회지
• /
• 제10권2호
• /
• pp.178-189
• /
• 1993

Engineering ceramics have some excellent properties as the material for the mechanical components. It is, however, very difficult to grind ceramics with high efficiency because of their high strength, hardness and brittleness. In this paper experiments are carried out to obtain the effect of "In-process dressing" to grind the Engineering ceramics with high efficiency. To save running time for dressing process and obtain restraint effect of diamond grain wear, "In-process dressing" system usint WA stick type honing stone is proposed. Representative High Strength Engineering ceramics A1$_{2}$O$_{3}$ and Si$_{3}$N$_{4}$are ground with diamond wheel. Also bending strengrh test is carried out to check upward tendancy of mecahnical properties as the result of machining defact restraint through the grinding maching method using "In-process dressing" process. Some results obtained in this study provide useful information to attain the high efficency grinding and the high mechanical properties of Engineering ceramics.rties of Engineering ceramics.