• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.557-564
• /
• 2002

Corrugated board is an efficient low-cost structure material fur the boxes that are widely used for transporting, storing and distributing goods. Corrugated board is also considered as an orthotropic because the principal material directions are the same as in paperboard. The purpose of this study was to elucidate the principal design parameters of ventilating box through the FEA on the various types of ventilating hole. From the viewpoint of the stress distribution and stress level, the optimum pattern and location of the ventilating hole were vertically oblong, and symmetry position with a short distance to the right and left from the center of front and rear panel. And, the optimum location and pattern of hand hole were a short distance to the top from the center of both side panels, and modified shape to increase the radius of curvature of both side in horizontal oblong. In general, the optimum pattern and location of both the ventilating hole and hand hole based on the FEM analysis were well verified by experimental investigation. It is suggested that decrease in compressive strength of the box could be minimized in the same ventilating hole area under the condition of the length of major axis of ventilating hole is less than 1/4 of box length, the ratio of minor axis/major axis is 113.5∼l/2.5, and number of the ventilating holes is even and symmetrical.

• 대한전자공학회논문지SD
• /
• 제47권12호
• /
• pp.55-67
• /
• 2010

고다층 배선 기판에 형성된 개방 스터브(open stub)를 제거한 후면드릴가공홀(Back-Drilled-Hole, BDH)과 일반적인 구조인 관통홀(Plated-Through-Hole, PTH) 구조의 전기적 특성에 대한 분석을 하였으며, 고속 선호를 부품 실장면으로부터 내층의 스트립라인으로 전송하기 위해 비아홀의 급전 길이가 가장 긴 전송층을 선택하였다. 10 GHz의 광대역 주파수 내에서 실험계획법(DOE, design of experiment)을 적용하여 비아홀 구조 내에 외층과 급전층 사이의 비아홀의 길이, 접지층에 형성된 천공(anti-pad)의 크기와 급전층에 형성된 패드 (pad)의 크기가 최대 반사 손실 반전력 주파수와 삽입 손실에 미치는 영향을 분석하였다. 이로 부터 거시적 모델(macro model)을 위한 회귀 실험식을 추출하여 실험 결과와 비교 평가하였고, 실험 영역 외에서도 측정 결과와 5% 이내의 오차를 보이고 있음을 확인하였다.

• 한국포장학회지
• /
• 제7권2호
• /
• pp.25-30
• /
• 2001

Corrugated board is composed of cellulose fibers which are arranged with the same direction as the board manufactured. The direction is classified with machine direction (MD) and cross-machine direction (CD). Therefore, corrugated board is orthotropic material that has totally different strength properties at each direction and especially, at machine direction, the mechanical properties of fiberboard is superior. The compression strength of the corrugated fiberboard boxes is very important information to the manufacturers and the end users. This study was carried out to design the optimum pattern, size, and location of ventilating hole for ventilating container through the finite element analysis. The optimum pattern and location of ventilating and hand hole were vertical oblong, a short distance to the right and left from the center of panel, and center or a short distance to the top of both sides, respectively. We identified the effect on both stress dispersion and stress level from the analysis of redisigned hand hole.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.289-296
• /
• 1999

The integration of the LSI has been greatly improved and the circuit patters on the LSI are becoming finer line and pitch. The high-density electronic packaging technology is improved. In order to realize the high-density packaging technology, the density of the circuit wiring of the printed circuit boards have also been more dense. The build-up process multilayer printed circuit board technology have a lot of vias, possibilities of the finer conductor wirings and have a freedom of capabilities of wiring design. The build-up process printed circuit boards have the wiring rules which are the pattern width: $100-20\mu\textrm{m}$, the via hole diameter: $100-50\mu\textrm{m}$. There three kinds of build-up processes as far materials and hole drilling. In this paper, the recent technology trends of the build-up printed circuit board technologies are described.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1069-1070
• /
• 2013

• 한국가구학회지
• /
• 제19권3호
• /
• pp.211-218
• /
• 2008

This experiment was carried out to investigate the effect of internal holes on the bending strength of PB. The diameters of holes are 0mm to 13mm. The locations of holes are 1/8 to 4/5 point horizontally from sample end and are 1/5 to 4/5 vertically from sample surface, the numbers of holes are 1 to 4 pcs. In the size of internal holes, the bending strengths of PB were decreased significantly with the increase of diameter of holes, and the relationship between diameters(D) of holes and bending strength (${\sigma}_b$) of PB was ${\sigma}_b=-11D+168.8$ ($r^2=-0.99^{**}$). The effects of hole-locations and hole-numbers on the bending strengths of PB were large. and so they should be considered as major factors for the jointing design of PB.

• 생명과학회지
• /
• 제24권3호
• /
• pp.290-296
• /
• 2014

이 연구의 목적은 mice를 이용하여 elevated plus-maze (EPM) test와 hole-board test를 통해 quercetin의 잠재적인 항불안 작용을 확인하고자 함이다. Quercetin을 1.25, 2.5, 5나 10 mg/kg의 용량으로 각각 행동시험을 측정하기 1 시간 전에 ICR mice에 경구투여하였다. 대조군은 동일한 양의 10% Tween 80을 투여하였고 양성대조군으로 buspirone 2 mg/kg을 투여하였다. Quercetin을 단회 투여하여 EPM test를 실시한 결과, 5 mg/kg 용량에서 open arm에 머문 시간 및 진입한 횟수의 백분율이 control group과 비교하여 통계적으로 유의성 있게 증가하였다(p<0.05). 또한 quercetin을 투여하여 hole-board test를 실시한 결과, 5 mg/kg 용량에서 구멍에 머리를 넣은 횟수가 control group과 비교하여 통계적으로 유의성 있게 증가하였다(p<0.05). 또한 quercetin와 flumazenil ($GABA_A$ antagonist), WAY-100635 ($GABA_{A-{\rho}}$ antagonist) 또는 trans-4-aminocrotonic acid ($GABA_{A-{\rho}}$ agonist)를 병용투여하여 elevated plus-maze를 실험을 하여 신경계와의 관계를 확인한 결과, trans-4-aminocrotonic acid에서만 quercetin의 항불안 작용이 차단되었음을 확인 할 수 있었다. 결론적으로, 본 연구의 결과에서 quercetin이 elevated plus-maze 및 hole-board test, horizontal wire test, open field test를 통하여 locomotor activity 및 근육이완이나 진정 등의 부작용이 없으면서 우수한 항불안 작용을 가지는 소재라고 생각되며 이러한 작용이 특히 GABA 신경계와 관련이 있음을 시사하고 있다.

• 마이크로전자및패키징학회지
• /
• 제19권4호
• /
• pp.39-43
• /
• 2012

Via-filling plating and through-hole plating are absolutely imperative for manufacturing of printed-wiring board. This Paper is introducing the latest developments of our company worked on the high-performance of acid copper plating additives for them.

• KIEAE Journal
• /
• 제7권4호
• /
• pp.135-140
• /
• 2007

In this study we settled the trouble of the MgO board of existence by this research. We changed the wooden one of the main ingredient of a board to a perlite and a mineral particle in the aluminum hydroxide group and proceeded with a study to physical character and fire resistance efficiency improvement. The result yellowing phenomenon could be improved and it was possible to reduce size decrease of pin hole and the frequency of occurrence. We found out that the in case of absorbed amount added 5~8% corresponding to the weight decreases the acrylic group emulsion suddenly. So this product is improved with the bending strength and water-resistance. After behavior stop time measurement of a mouse for experiments was measured at the time of a gas harmful effect test, an improved MgO board appeared more highly for an average of 138 seconds compared with a board of existence.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.244-248
• /
• 1987

The force/torque sensor for robot is developed. The compliance algorithm for peg-in-hole insertion task using the forec/troque sensor is developed. The system consists of an IBM PC, robot, force/torque sensor, strain meter, A/D board, and interface board. The IBM PC functions as a main processor and the robot controller as a slave processor. The sensor is constructed to measure $T_x$, $T_y$, $F_z$ which are necessary to precisely execute a peg-in-hole insertion task by SCARA type assembly robot. The outputs of sensor are analyzed. On the basis of the analysis, compliance algorithm for peg-in-hole insertion task is developed. Some comments concerning the development of wrist force/torque sensor and compliance algorithm are given.