• Corrosion Science and Technology
• /
• 제23권2호
• /
• pp.145-153
• /
• 2024

In the automotive industry, the hole expanding test is widely used to assess the formability of punched holes in sheets. This test provides a good representation of formability within the framework defined by the ISO 16630 standard. During hole expanding tests on galvanized high strength steels, a negative effect was observed when there was a delay between hole punching and expansion, as compared to performing both operations directly. This effect is believed to be caused by hydrogen aging, which occurs when hydrogen diffuses towards highly-work hardened edges. Therefore, the aim of this study is to demonstrate the migration of hydrogen towards work-hardened edges in high strength Zn-coated steel sheets using a novel Thermal Desorption Analyzer (TDA) designed for small samples. This newly-developed TDA setup allows for the quantification of local diffusible hydrogen near cut edges. With its induction heating and ability to analyze Zn-coated samples while reducing artifacts, this setup offers flexible heat cycles. Through this method, a hydrogen gradient is observed over short distances in shear-cut galvanized steel sheets after a certain period of time following punching.

• Nuclear Engineering and Technology
• /
• 제42권4호
• /
• pp.382-393
• /
• 2010

Thermal mixing by steam jets in a pool is dominantly influenced by a turbulent water jet generated by the condensing steam jets, and the proper prediction of this turbulent jet behavior is critical for the pool mixing analysis. A turbulent jet flow induced by a steam jet discharged through a vertical upward single hole into a subcooled water pool was subjected to computational fluid dynamics (CFD) analysis. Based on the small-scale test data derived under a horizontal steam discharging condition, this analysis was performed to validate a CFD method of analysis previously developed for condensing jet-induced pool mixing phenomena. In previous validation work, the CFD results and the test data for a limited range of radial and axial directions were compared in terms of profiles of the turbulent jet velocity and temperature. Furthermore, the behavior of the turbulent jet induced by the steam jet through a horizontal single hole in a subcooled water pool failed to show the exact axisymmetric flow pattern with regards to an overall pool mixing, whereas the CFD analysis was done with an axisymmetric grid model. Therefore, another new small-scale test was conducted under a vertical upward steam discharging condition. The purpose of this test was to generate the velocity and temperature profiles of the turbulent jet by expanding the measurement ranges from the jet center to a location at about 5% of $U_m$ and 10 cm to 30 cm from the exit of the discharge nozzle. The results of the new CFD analysis show that the recommended CFD model of the high turbulent intensity of 40% for the turbulent jet and the fine mesh grid model can accurately predict the test results within an error rate of about 10%. In this work, the turbulent jet model, which is used to simply predict the temperature and velocity profiles along the axial and radial directions by means of the empirical correlations and Tollmien's theory was improved on the basis of the new test data. The results validate the CFD model of analysis. Furthermore, the turbulent jet model developed in this study can be used to analyze pool thermal mixing when an ellipsoidal steam jet is discharged under a high steam mass flux in a subcooled water pool.

• 한국항공우주학회지
• /
• 제30권2호
• /
• pp.46-51
• /
• 2002

홀 확장법은 홀 주위에 압축 잔류응력 층을 생성시킴으로서 균열 발생을 지연시키는 방법으로 항공산업 분야에서 널리 사용되고 있다. 홀 확장잔류응력의 분포는 홀 확장률, 맨드럴 삽입방향, 재료 물성치 등 여러 가지 홀 확장 파라미터에 따라 달리진다. 홀 확장 잔류응력 층의 정확한 파악이 항공사업의 실제 설계에 있어서 매우 중요함에도 불구하고 이에 대한 연구는 상대적으로 부족하였다. 본 연구에서는 3차원 유한요소해석을 통하여 알루미늄 평판에 홀 확장법을 적용하는 경우의 잔류응력 분포를 예측하고자 하였다. 유한요소해석의 타당성을 검증하기 위하여 스트레인 게이지를 이용한 홀 확장 잔류변형률을 측정하였으며, 홀 확장률과 2단 홀 확장이 잔류응력 분포에 미치는 영향을 파악하였다. 2단 홀 확장을 적용함으로써 최대 압축 잔류응력의 크기가 약 7% 향상됨을 알 수 있었다.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.487-493
• /
• 2012

To analyze the factors on stretch-flangeability for 980 MPa-grade hot-rolled steels, two types of steels (Fe-Cr and Fe-Mo) were manufactured by hot-rolling. Manufactured steels at the low coiling temperature, such as 400 and $500^{\circ}C$, had poor stretch-flangeability due to un-uniformly distributed carbides and a large deviation of interphase hardness. However, when the coiling temperature was set at $650^{\circ}C$ with Fe-Cr steel, 998 MPa of ultimate tensile strength, 19% of total elongation and 65% of the hole expanding ratio were achieved by microstructural constituents of polygonal ferrite (PF) and granular ferrite (GF) dispersed with fine carbides (<50 nm). Therefore, the material to attain 980 MPa with superior formability was the Fe-Cr steel that was precipitation-hardened in polygonal ferrite and granular ferrite at the coiling temperature $650^{\circ}C$.

• 한국임상수의학회지
• /
• 제39권5호
• /
• pp.272-276
• /
• 2022

An 8 month old leopard gecko (Eublepharis macularius) with a large nodule was referred to our hospital. During the physical examination, the nodule had an unclear boundary from the top of the left eye to the front of the left ear and prevented the opening of the left eye. A hard, cheese-like, yellow, pus-filled nodule was observed. A cytological examination of a pus swab sample revealed pyogranulomatous inflammation with rod-shaped bacteria. Ofloxacin was chosen as the empirical topical antimicrobial drug for treatment. The swab samples were inoculated in trypticase soy agar with 5% sheep blood and incubated at 37℃ for 24 h. Gram-negative bacteria were identified via Gram staining, and the Kirby-Bauer antimicrobial susceptible disk diffusion test against 24 antibiotics according to protocol M100-Ed32 of CLSI showed that the fluoroquinolone group (ciprofloxacin and enrofloxacin) was susceptible to the isolated bacteria. Molecular identification based on 16S ribosomal RNA gene sequencing confirmed that the isolated bacteria had a 99.85% nucleotide similarity with Serratia surfactantfaciens (GenBank accession no. CP014948). After 1 week, the boundaries of the nodule became clear; thus, the abscess was physically removed by expanding the hole formed above the eye for drainage, and flushing was repeated. After another 1 week, new tissue restoration without scarring was observed. This is a rare case report of the successful management of a subcutaneous abscess and scar-free healing in a lizard.