• Journal of Mechanical Science and Technology
• /
• v.15 no.4
• /
• pp.482-491
• /
• 2001

An experimental study has been carried out to investigate an I-type sparger-performance in view of pressure oscillation and thermal mixing in a pool. Its pitch-to-hole diameter, P/D, varies from 2 to 5. The test conditions are restricted to the condensation oscillation regime. In the present study, two different hole patterns, staggered and parallel types, are employed under various test conditions. The amplitude of the pressure pulse shows a peak for pool temperatures of 45∼85$\^{C}$, which depends on P/D and the steam mass flux. The effect of hole pattern on the pressure load is smaller than that of P/D. The dominant frequency increases with the subcooling temperature of pool water and P/D. A correlation for the dominant frequency is proposed in terms of the pitch-to-hole diameter ratio and other dimensionless thermal hydraulic parameters.

• Journal of ILASS-Korea
• /
• v.17 no.4
• /
• pp.210-215
• /
• 2012

This paper This paper presents effect of nozzle hole number on spray characteristics and engine performance. Experiments were conducted to measure spray penetration and SMD distributions using a spray visualization system and PDPA (phase Doppler particle analyzer) system. In addition, engine performance and emission characteristics were measured using a single cylinder engine and emssion measurement systems. Results showed that 8-hole-injector exhibits improved spray performances. Furthermore, soot emission was decreased with 8-hole-injector, compared to that of 6-hole-injector.

• International Journal of Safety
• /
• v.8 no.1
• /
• pp.1-5
• /
• 2009

The CFRP composite has unique properties that offer high strength and stiffness, even though it has light weight. Therefore it can be used in many industrial applications. When mechanical fasteners are used for joining composites, high stress concentrations appear near the edge of holes prepared for accommodating structural bolts and rivets. This presence of high stress concentrations can be a source of damage. The aim of this work is to evaluate fracture behavior and patterns of plain woven CFRP with circular hole and repairing patch element. The maximum strength and pattern for the plain woven carbon composite specimen with the repaired circular hole were examined. From the results, we show that repairing of the CFRP composite specimen with ($\pi$) 3~5 mm of circular hole diameter results in load rising effect and the repairing is more effective as bigger hole specimen.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.796-799
• /
• 2002

The stress of the rotating disc with several types of hole was investigated in detail in this paper. Maximum circumferential stress of rotating disc by changing hole shape with same area, were studied using FEM. The results obtained were as follows: 1. The disc which rotates at high speed is subjected to circumferential stress remarkably. 2. When the number of circular holes in rotating disc is four, stress reduction effect is maximum. 3. When shape of holes in rotating disc is cylindrical elongated hole, maximum circumferential stress of the rotating disc decreased most.

• Explosives and Blasting
• /
• v.34 no.2
• /
• pp.1-9
• /
• 2016

In this study, the field tests were performed on V-cut, PLHBM 1 hole, PLHBM 2 hole in gneiss area in order to compare the effects of the vibration decay of a tunnel cut-hole according to the number of PLHBM holes with scaled distance. Based on the prediction equation of blasting vibration from the result of the tests, the decay rate of vibration were confirmed 21.8~61.1% using PLHBM 1 hole, 35.7~79.3% using PLHBM 2 hole for scaled distance within $10{\sim}100m/kg^{1/2}$ on the basis of V-cut PPV. As the scaled distance was increased, the effect of vibration decay was decreased. The effect of vibration decay of cut-hole for intial PLHBM 1~2 hole was significantly high.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.574-578
• /
• 2003

The objective of this paper is to decide optimal location of pin-hole to minimize stress concenstation around hole in rotating disc. The focus of this investigation is to evaluate the effect of pin-hole for stress distribution around hole using optimum design technic and finite element analysis. Design variables are radial and angular location of pin-hole from center of hole, objective function is maximum stress around hole in rotating disc. We use first order method of optimization technic.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.72-79
• /
• 1997

The dominant physical process repsonsible for the nonlinear gain is from spectral-hole burning with the time constant fo about 50fs and the contribution to the nonlinea rgain form hot carriers effect is determined to be about 15% of the contribution due to spectral-hole burning. To prove the above results we fit the data of hall and found that hot carriers have a profound effect on their experimental data despite the fact that the magnitude of hot carriers effect is only 15% of spectral-hole burning. We suggest that the experimenta with a pump pulse width of 180 fs is very sensitive in detecting the effect of hot carriers, but is not sensitive in detecting much faster process associated with spectral-hole burning.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.3
• /
• pp.763-769
• /
• 2012

We investigated the width (N) dependence on the magnetization of N-ZSiC NR with electron and hole doping on the basis of systematic DFT calculations. The critical values of the upper and down critical concentration to give the maximum and zero magnetic moment at edge Si/C atoms by electron/hole doping ($x_{up,e}$, $x_{down,e}$, $x_{up,h}$, and $x_{down,h}$) depend on the width of N-ZSiC NR. Moreover, due to $x_{up,e}\;{\neq}\;x_{up,h}$ and $x_{down,e}\;{\neq}\;x_{down,h}$, the electron and hole doping effect are asymmetry, i.e, the critical electron doping value ($x_{down,e}$) is smaller than the critical hole doping value ($x_{down,h}$) and is almost independent of the width of NZSiC NR though the other critical values of the electron and hole doping that influence the magnetization of N-ZSiC NR depend on the width. It was also found that at $x_{down,e}$ or $x_{down,h}$ doping, the N-ZSiC NR turns into unusual non-magnetic metallic state. The magnetic behavior was discussed based on the band structures and projected density of states (PDOS) under the effect of electron/hole doping.

• Advanced Composite Materials
• /
• v.18 no.1
• /
• pp.43-59
• /
• 2009

The current study assessed the effect of a bolt hole on tensile fatigue properties of CFRP laminates. Two specimens, i.e. $[(0/90)_3]S$, $[(0/45/90/-45)_2]_S$, were analyzed using a finite element method and were experimentally tested for cases, both with and without a hole, whose diameter corresponded to 0.12 times the specimen width. Delamination positions predicted by a 3-dimensional static finite element analysis were matched well to those observed by an ultrasonic imaging system in the middle of fatigue test. A hole whose diameter corresponds to 0.12 times the specimen width caused the fatigue strength to decrease by 9% and 11% under 5 Hz loading frequency, and by 22% and 25% under 10 Hz loading frequency for $[(0/90)_3]_S$ and $[(0/45/90/-45)_2]_S$, respectively. Because the decrease in sectional area due to the hole was normalized in calculation of the tensile strength, a stress concentration around the hole is believed to induce the strength degradation of fatigue specimens. From the finite element analyses, the stress concentration factor around a hole was expected as 8.8 and 9.5 for $[(0/90)_3]_S$ and $[(0/45/90/-45)_2]_S$, respectively.

• Transactions of Materials Processing
• /
• v.30 no.2
• /
• pp.74-82
• /
• 2021

Stretch-flangeability, which is the ability of sheet steels to be deformed into complex shapes, is a critical formability property in automobile body parts. In this study, the center-hole for hole expansion test, which is normally used to evaluate the stretch-flangeability of sheet steels, was prepared by both punching and electrical discharge machining (EDM) methods. Hole expansion ratio (HER) of punched hole was far lower than the HER of EDM drilled hole because of damage/crack in hole-edge due to punching process. The effect of hole-edge condition on HER was quantified by mechanical, fractographic and geometric factors. Based on these factors, the empirical equation used to determine HER for various sheet steels was derived using non-linear regression.