• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.362-365
• /
• 2005

The hub hole is usually formed with a flanging process followed by a blanking process of a ]tole. Since the hole is made by blanking, the blanked surface is so rough that the formability in the region is rather poor. The emerging task is to identify the formability of the blanked region in the forming simulation and to relate the criterion to the real forming process by experiments. In this paper, hole expansion tests are carried out with respect to various hole conditions to verify the hole condition effect on the hole expansion ratio. The hole of specimens is made by machining or punching. In the case of punching, two different punching clearances are used for making the hole. From the results of test, fracture mechanism of the hole expansion is explained.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.761-764
• /
• 2002

This paper deals with the stress concentration of the rotating disc in detail. We studied maximum stress of rotating disc with respect to the various parameter of circular hole such as position, size, number of the hole, then the mollified effect of maximum stress due to pin-hole around circular hole, using FEM, the results are as follows: 1. The more the number of circular hole and the further from the center, the maximum equivalent stress reduces. 2. When the pin-hole is located 60$^{\circ}$ from the x-axis, the maximum stress reduces significantly due to the effect of interference.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.3
• /
• pp.341-351
• /
• 2016

In this present work, the effect of hole shapes, orientation and hole arrangements on film cooling effectiveness has been carried out. For this work a flat plate has been considered for the computational model. Computational analysis of film cooling effectiveness using different hole shapes with no streamwise inclination has been carried out. Initially, the model with an inclination of $30^{\circ}$ has been verified with the experimental data. The validation results are well in agreement with the results taken from literature. Five different hole shapes viz. Cylindrical, Elliptic, Triangular, Semi-Cylindrical and Semi-Elliptic have been compared and validated over a wide range of blowing ratios. The blowing ratios ranged from 0.67 to 1.67. Later, orientation of holes have also been varied along with the number of rows and hole arrangements in rows. The performance of film cooling scheme has been given in terms of centerline and laterally averaged adiabatic effectiveness. Semi-elliptic hole utilizes half of the mass flow as in other hole shapes and gives nominal values of effectiveness. The triangular hole geometry shows higher values of effectiveness than other hole geometries. But when compared on the basis of effectiveness and coolant mass consumption, Semi-elliptic hole came out to give best results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.1
• /
• pp.147-152
• /
• 2002

Effect of lip shape on the hole flangeability of high strength steel sheets is investigated. Circular plates of various hole sizes are tested and the variation of lip length as well as the variation of thickness on the sectional views of the finished lip were studied. The conventional hole flanging process is limited to a certain limit hole diameter below which failure will ensue during the hole expansion. The intention of this work is to examine the effect of lip shape on the flangeability of TRIP steel and Ferrite-Bainite duplex steel and find out major parameters which can affect flanging shape of high strength hot rolled steels. Over the ranges of conditions investigated, the minimum hole diameter of F+B steel is better than TRIP steel. while, the lip-shape accuracy of TRIP steel is better than that of F+B steel. although the tensile strength and elongation of %P steel are superior than those of Ferrite-Bainite duplex steel, the flangeability is found to be not so strongly sensitive to the tensile properties but sensitive to displacement on the circumferential direction of hole edge.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1518-1520
• /
• 2008

Recent clinical studies have shown that computer navigation for total knee arthroplasty (TKA) provides improved component alignment accuracy. However, femoral stress fracture after computernavigated TKA have been reported due to the pin hole and we hypothesized that osteoporosis would be one of the key factors in pin hole fracture after computer-navigated TKA. We investigated the von-Mises stress around the femoral pin-hole for different elastic modulli and ultimate stresses and four different pin penetration modes to understand the aging effect on femoral stress fracture risk after computer-navigated TKA by finite element analysis. In this study, aging effect was shown to increase the femoral stress fracture risk for all pin penetration modes. Especially, aging effect was shown dramatically in the transcortical pin penetration mode.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.5
• /
• pp.295-304
• /
• 2002

In this study, the effect of the diameter and the number of barrel hole on the total area of barrel hole were calculated and analyzed. And the effects of applied current density, rotational speed of the barrel, size and number of barrel hole, and the volume of plating materials on the distribution of plating thickness were experimented and discussed by the barrel electroplating of the tube type brass specimens in a sulfamate nickel barrel solution. The effect of barrel hole size and barrel hole area on the throwing power was also discussed.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.424-427
• /
• 2017

This study investigated the effect of strain on hole mobility and hole effective mass in a p-channel rectangular nanowire with two-dimensional confinement. We obtained the valence energy band structure using the six-band k.p method and calculated the mobility and effective mass of the hole in the [100] direction taking the strain effect into account in the inversion region. The hole mobility of strained silicon was calculated using Kubo-Greenwood formalism. As a result, it showed good performance compared to relaxed silicon, but its magnitude was insignificant.

• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.76-82
• /
• 1990

Lots of research works have been done to improve the accuracy of the hole drilling method to measure residual stress by many investigators. In this study, first, size effect of specimen was analyzed based on the solution of hole in a strip under tension. If the ratio of hole diameter tothe strip width is less than 0.2, the stress distribution around hold may be given from the solution of hole in an infinite plate. Second, the residual stress above $0.6{\sigma}_y$(yield stress) may be measured less than the actual stress by 10-15 percent. Third, eccentricity of hole relative to the rosette center effects on the accuracy of residual stress measurements by 10 percent. The error due to eccentricity of hole can be corrected by the iteration method or the direct method.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.186-193
• /
• 2004

Porous anodic alumina has been used widely for corrosion protection of aluminum surfaces or as dielectric material in micro-electronics applications. It exhibits a homogeneous morphology of parallel pores which can easily be controlled between 10 and 400nm. It has been applied as a template for fabrication of the nanometer-scale composite. In this study, mechanical properties of the AAO structures are measured by the nano indentation method. Nano indentation technique is one of the most effective methods to measure the mechanical properties of nano-structures. Basically, hardness and elastic modulus can be obtained by the nano-indentation. Using the nano-indentation method, we investigated the mechanical properties of the AAO structure with different size of nano-holes. In results, we find the hole effect that changes the mechanical properties as size of nano hole.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.216-220
• /
• 2014

This paper presents effect of nozzle hole number on atomization characteristic of DME fuel spray using three different type of injector having the hole number of 6, 7 and 8. For this study, PDPA(phase Doppler particle analyzer) experiment was performed in terms of $T_{ASOE}$ under various injection pressure. To compare general trend of atomization characteristic, the law data were ensemble averaged based on $T_{eng}$ of 0.2 ms. Results showed that the droplet diameter in terms of SMD(Sauter Mean Diameter) was reduced as increase in injection pressure. Increasing the number of hole lead to reduce in droplet diameter, but no significant reduction in diameter was observed between hole number of 7 and that of 8. In addition, increasing the number of hole resulted in decrease in droplet velocity which is considered as the effect of reduction in spray momentum due to decreasing of fuel quantity per each hole.