• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.220-223
• /
• 2002

This paper introduces the development procedure of paddle type small-scaled composite rotor blade for helicopter hingeless rotor system. Paddle type composite blade design was done by using CORDAS program developed by KARI and dynamic analysis for hingeless hub with blade is done by using FLIGHTLAB which is commercial software for helicopter comprehensive analysis. The procedure to manufacture complicated shape of paddle type blade tip was developed and composite blades were manufactured after establishing the effective curing method. Through this research, the development technology of composite rotor blade with complex aerodynamic shape were accumulated and these will be applied to the related research field, for example, full size composite blade development, etc.

• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.54-64
• /
• 2006

To augment weakly damped lag mode stability of a hingeless helicopter rotor blade in hover, piezoelectric shunt with a resistor and an inductor circuits for passive damping has been studied. A shunted piezoceramics bonded to a flexure of rotor blade converts mechanical strain energy to electrical charge energy which is dissipated through the resistor in the R-L series shunt circuit. Because the fundamental lag mode frequency of a soft-in-plane hingeless helicopter rotor blade is generally about 0.7/rev, the design frequency of the blade system with flexure sets to be so. Experimentally, the measured lag mode frequency is 0.7227/rev under the short circuit condition. Therefore the suppression mode of this passive damping vibration absorber is adjusted to 0.7227/rev. As a result of damping enhancement using passive control, the passive damper which consists of a piezoelectric material and shunt circuits has a stabilizing effect on inherently weakly damped lag mode of the rotor blades, at the optimum tuning and resistor condition.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.173-176
• /
• 2002

This paper describes the design procedure of composite parts for hingeless hub system of helicopter. These composite parts are composed of flexure and sleeve. The design of this composite flexure is an important technique in hingeless hub system since the rotor system stability and dynamic characteristics depends on this flexure characteristics. The objective of this research is to replace the existing metal hub parts with composite to improve the performance and stability. First, the coupon test of candidate composite material for hub parts was conducted. The hub parts was designed based on test results and the manufacturing possibility by using Fiber Placement System(FPS) was checked. Also the dynamic analysis and stress analysis of composite hub parts was conducted. Through this research, we will find out the possibility of replacing existing metal hub parts with composite.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.213-216
• /
• 2005

This paper describes the design, analysis and manufacture procedure of the composite blade for hingeless rotor system of unmanned helicopters. Helicopter rotor system is the key structural unit that produces thrust and control forces for intended flight conditions. In this work, a hingeless rotor system is adopted, and base on the design requirements for rotor system, composite blade section design and calculation of material properties were performed. In order to avoid the unstable state such as resonance, vibration characteristics of rotor system were analyzed. Finally, this paper describes simply the forming and manufacture of composite blade.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.119-122
• /
• 2003

This report describes the procedure of detailed design and structural test for the composite flexure which is a part of the hingeless hub system. First, stacking sequence design for composite flexure was done, and structural analysis by using NASTRAN was made to verify structural stability and safety. Using FPS installed at KIMM, composite flexure was laid up and cured using a autoclave. Before rotor ground test, the basic structural tests such as a bench test, tensile strength test and shear strength test, for flexure, were accomplished. Through replacing existing metal hub part with new fabricated composite flexure, improvement of aeroelastic stability and weight reduction were achieved. This result will be applied to composite rotor system design fur helicopter.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.105-111
• /
• 2013

Whirl tower test is conducted basically during helicopter rotor system development process. And for whirl tower test of rotor hub system, new design blade or existing blade which is remodeled for new rotor hub system is used. Because of simple shape and efficient aerodynamic characteristic, BO-105 helicopter blade is used for helicopter rotor hub development project widely. Originally BO-105 blade is used for hingeless hub system and blade root is used to flexure. So flap stiffness and lag stiffness at blade root area is relatively low compare with airfoil area. So, in order to apply the BO-105 blade to bearingless hub, blade root area have to be reinforced. And in this process, blade root area's section property is changed. In this paper, we suggest reinforcement method of BO-105 blade root area and study dynamic characteristic of bearingless rotor system with reinforcement BO-105 blade.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.310-315
• /
• 2003

This paper described that rotating test and fatigue test of a small-scale hingeless hub system with composite rectangular blades. Generally Rotating stability and fatigue test technique is one of Key-technology on test and evaluation for helicopter rotor system Rotating test of hingeless rotor system was achieved by means of rotor vibration characteristic and aeroelastic stability test GSRTS, equipped with hydraulic actuator and 6-component rotating balance was used to test hingeless rotor system especially for an observation of blade motion including flawing, lagging and feathering. Rotating test was done in hover and forward flight condition. Small-scaled blade fatigue test condition was determined by blade load analysis with the reference table of composite materials(S-N curve). Fatigue test bench was developed for the estimation of blade fatigue life, and tested its characteristic.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.3
• /
• pp.6-14
• /
• 2007

In this research, vibration reduction and aeroelastic stability of a composite hingeless rotor hub flexure with viscoelastic constrained layer damping treatment(CLDT) were investigated. The composite flexures with viscoelastic CLDT were applied to hingeless rotor system to improve the in-plane stability of the lead-lag motion causing resonance. The modal test was performed and dynamic properties(natural frequency and loss factor) were acquired. Also, complex eigenvalue analysis(SOLlO7) in the NASTRAN structural analysis module was performed and compared with results of the modal test. To insure aeroelastic stability, damping ratio analyses of the hingeless rotor system with CLDT were accomplished at hovering condition due to collective pitch angle changes. Satisfactory results of increasing structural damping and stability were obtained.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.333-334
• /
• 2011

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.206-209
• /
• 2001

This paper contains the development procedure of small-scaled composite rotor blade for helicopter hingeless rotor system. Composite blade design is conducted by using CORDAS program developed by KARI and dynamic analysis is conducted by using Flightlab which is commercial software for helicopter analysis. Also the optimizing procedure of iterative design was described. The designed composite blades were manufactured after establishing the effective curing method. Through this research, the experiences of composite rotor blade development were accumulated and will be applied to the related research field.