• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.413-419
• /
• 2009

As the refractive index of the prism layer becomes higher, the optical performance of the prism sheet gets better and the efficiency of the LCD backlight unit is improved. In order to increase the refractive index of the prism layer, the ultraviolet curing type resins were prepared by mixing high refractive index materials containing aromatic groups and the multi-functional reactive diluents. By using 9,9-bis [4-(2-acryloyloxyethoxy)phenyl] fluorene, the refractive index of the prism layer was increased up to 1.58 and the brightness of the backlight unit was improved. Since the light source used in the backlight unit caused the yellowing in the prism sheet and deteriorated the brightness accordingly, the hindered amine light stabilizer was used to improve the yellowing resistance successfully.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.370-381
• /
• 2015

In the system of poly(vinyl alcohol) (PVA)/dimethyl sulfoxide, the refractive index of polymer was very well matched to that of solvent and thus its scattered intensity could be minimized. After adding small amount of polystyrene latex particle (nominal diameter 200 nm), diffusion behavior of only probe particle was investigated against the concentration of polymer matrix by means of dynamic light scattering. The polymer concentration dependence of its reduced diffusion coefficient was able to be analysed with the stretched exponential function of the reduced concentration $C[{\eta}]$. In very dilute concentration regime, the depletion layer kept constant but at the early semi-dilute regime of $1{\leq}C[{\eta}]{\leq}2.5$, the concentration-dependent exponent of depletion layer ${\delta}$ was appeared to be -0.8 which was very close to theoretical one of -0.85. However it was also observed at the higher concentration that its layer thickness decreased more abruptly than theoretical expectation and this phenomenon was ascribed to Oosawa type attractive interaction between adjacent latex particles.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.158-161
• /
• 2006

Recently the application of plastic optical fiber (POF) in automotives and planes demands the heat-resistant and high refractive index con materials. We synthesized polyglutarimides (PGIs) via imidization of PMMA with primary amines under high pressure and high temperature and investigated thermal and optical properties by varying the molar ratio of amines and the type of amines (ethyl amine vs. isopropyl mine). The degree of imidization was calculated based on the peak intensity in $^1H$ NMR and FTIR. We found that the glass transition temperature $(T_g)$ of PGIs increased over $30^{\circ}C$ compared to the traditional core materials in POF, PMMA, and they are stable up to $300\sim400^{\circ}C$. PGIs anthesized with ethyl mine show the better heat resistance than those with isopropyl amines. Additionally, they show the comparable transparency and higher refractive index than PMMA. It implies that they can be utilized as the excellent photo-efficient and heat-resistant core materials in POF.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.1
• /
• pp.1-9
• /
• 2012

In this study, 5 solvent soluble polymers were treated on Hanji. Mechanical properties, morphology and oxidation index with thermal aging were measured on the aged Hanji, dewaxed Hanji and polymer treated Hanji. Synthetic polymers(such as polylactic acid, polybutylene succinate, polystyrene) treated Hanji had higher strength and thermal stability than cellulose derivatives(such as cellulose nitrate and cellulose acetate) treated Hanji. Polymer treated Hanji showed a little bit of color change. The oxidation index of PS treated Hanji did not increase with thermal aging because it did not have a carboxyl group in chemical structure. Finally, polystyrene was found to be the most efficient method for strengthening the dewaxed Hanji. The best aging safety and thermal stability were obtained at the polystyrene 3% solution.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.306-313
• /
• 2020

To investigate the reinforcing effects of functional fillers in nitrile rubber (NBR) materials, high-structure carbon black (HS45), coated calcium carbonate (C-CaCO3), silica (200MP), and multi-walled carbon nanotubes (MWCNTs) were used as functional filler, and carbon black (SRF) as a common filler were used for oil-resistant rubber. The curing and mechanical properties of HS45-, 200MP-, and MWCNT-filled NBR compounds were improved compared to those of the SRF-filled NBR compound. The reinforcing effect also increased with a decrease in the particle size of the fillers. The C-CaCO3-filled NBR compound exhibited no reinforcing effect with increasing filler concentration because of their large primary particle size (2 ㎛). The reinforcing behavior based on 100% modulus of the functional filler based NBR compounds was compared by using several predictive equation models. The reinforcing behavior of the C-CaCO3-filled NBR compound was in accordance with the Smallwood-Einstein equation whereas the 200MP- and MWCNT-filled NBR compounds fitted well with the modified Guth-Gold (m-Guth-Gold) equation. The SRF- and HS45-filled NBR compounds exhibited reinforcing behavior in accordance with the Guth-Gold and m-Guth-Gold equations, respectively, at a low filler content. However, the values of reinforcement parameter (100Mf/100Mu) of the SRF- and HS45-filled NBR compounds were higher than those determined by the predictive equation model at a high filler content. Because the chains of SRF composed of spherical filler particles are similarly changed to rod-like filler particles embedded in a rubber matrix and the reinforcement parameter rapidly increased with a high content of HS45, the higher-structured filler. The reinforcing effectiveness of the functional fillers was numerically evaluated on the basis of the effectiveness index (��SRF/��f) determined by the ratio of the volume fraction of the functional filler (��f) to that of the SRF filler (��SRF) at three unit of reinforcing parameter (100Mf/100Mu). On the basis of their effectiveness index, MWCNT-, 200MP-, and HS45-filled compounds showed higher reinforcing effectiveness of 420%, 70%, and 20% than that of SRF-filled compound, respectively whereas C-CaCO3-filled compound exhibited lower reinforcing effectiveness of -50% than that of SRF-filled compound.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.399-403
• /
• 2007

Trans-esterification behavior of polycarbonate/poly(butylene terephthalate) (PC/PBT) blends was investigated during the melt mixing process. Rheological and fracture behaviors, and fracture morphology were also investigated as a function of PC/PBT blend ratio. Based on FT-IR and $^1H-NMR$ results, a trans-esterification reaction was confirmed to occur between PC and PBT during the melt mixing process. The melt index(MI) decreased with increased PC content, indicating the higher flow resistance of PC. The storage and loss moduli were increased by increasing the PC loading, and the PC/PBT blends were rheologically incompatible based on the Cole-Cole plot. The tensile property increased linearly with the increased PC content. However, the impact strength increased until 50 wt% of PC loading, notably around $30{\sim}40wt%$, and then was levelled off at 50 wt%. Rough ridges were formed on the impact fracture surfaces above the 40 wt% of PC content, supporting the observed higher impact strength in this range.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2014

Purpose: To observe changes of coatings and lens materials with varying temperature to understand effect of temperature on plastic lens. Methods: In this study, three lenses of different refractive indices (2 of thiourethane oriented lenses, an allyl diglycol carbonate oriented lens) were exposed to high temperature (50, 80, and 100 degree) for 5 hours and changes of individual coating (anti-refractive coating, hard coating, and water repellent coating) were measured. Results: As a result, high-refractive index lenses did not exhibit significant variation of hardness. However, hardness of mid-refractive index lens were decreased when exposed to high temperature and destructions of hard coating layer was inferred. Surface contact angles of lens were decreased with increasing temperature and water repellent coating layer were damaged at higher than 80 degree. Conclusions: Multi including water repellent coatings on all three lenses with different refractive indices were damaged when exposed to at or higher than 80 degree. The degree of changes in mechanical and physical properties were depended on polymer material type.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.47-54
• /
• 2023

In this study, the tensile behavior of concrete specimens reinforced with GFRP (Glass Fiber Reinforced Polymer), BFRP (Basalt Fiber Reinforced Polymer), and CFRP (Carbon Fiber Reinforced Polymer) bars was experimentally analyzed. The tensile strength of the FRP bars is appeared to be similar to the design strength, but the elastic modulus was somewhat lower. Additionally, the specimens for tension stiffening effect were manufacured using OPC (Ordinary Portland Cement) and SFRC (Steel Fiber Reinforced Concrete), with dimensions of 150(W)×150(B)×1000(H) mm. The crack spacing of specimens was most significant for GFRP reinforcement bars, which have a lower elastic modulus and a smoother surface, while BFRP and CFRP bars, with somewhat rougher surfaces and higher elastic moduli, showed similar crack spacings. In the load-strain relationship, GFRP bars exhibited a relatively abrupt behavior after cracking, whereas BFRP and CFRP bars showed a more stable behavior after the cracking phase, maintaining a certain level of tension stiffening effect. The tension stiffening index was somewhat smaller as the diameter increased, and GFRP, compared to BFRP, showed a higher tension stiffening index.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.91-99
• /
• 2017

The purpose of this paper is to evaluate the flexural performance of reinforced concrete (RC) beams repaired with polymer mortar. The repaired and non-repaired 13th beams which was fabricated by considering repair position, repair depth, and curing age of polymer mortar as test variables were tested under three point loading. All specimens repaired in compressive and tensile zone did not fail due to interfacial failure between polymer mortar and concrete but failed when the strain of repaired mortar exceeded the ultimate tensile strain of polymer mortar. Maximum load of specimens repaired in compressive zone was similar to that of non-repaired specimen, reference specimen. Additionally, their ductility index was higher than that of reference specimen. On the other hand, specimens repaired in tensile zone failed very brittlely and have a lower ductility index than reference specimen. Nonlinear analysis by using OpenSees was performed to predict the behavior of RC beam repaired with polymer mortar. Two dimension frame element was used to simplify an analysis model and fiber model was applied to consider the material non-linearity. It was confirmed from the analysis results that nonlinear analysis properly predicts the behavior of specimens repaired in compressive zone and overestimates the behavior of specimens repaired in tensile zone.

• Korean Journal of Food Science and Technology
• /
• v.29 no.5
• /
• pp.932-938
• /
• 1997

Changes in viscosity and dynamic theological properties of Job's-tears were measured by Bohlin dynamic tester as a function of moisture, and measurement was performed within a linear viscoelastic range. The result of the shear stress vs shear rate of Job's-tears at different moisture contents $(50{\sim}75%)$ was applied to mathematical models and Herschel-Bulkley model showed the highest correlation coefficient. Lower moisture content (55%) produced higher yield stress and consistency index, but lower flow behavior index, whereas higher moisture content showed reverse effects. Job's-tears with $50{\sim}70%$ moisture contents showed a higher storage modulus (G') than loss modulus (G') at all frequencies, showing a higher concentrated polymer characteristics. However, higher moisture content (>75%) showed crossover point between G' and G', and frequency dependency. As the moisture content was increased, the amount of viscoelastic properties such as G', G', complex viscosity decreased during heating, and initial temperature and miximum value of viscoelastic properties shifted to higher temperatures, representing the moisture-dependence of Job's-tears upon theological properties.