• Geomechanics and Engineering
• /
• v.20 no.2
• /
• pp.103-112
• /
• 2020

The dynamic response of crossing tunnels under heavy-haul train loads is still not fully understood. In this study, based on the case of a high-speed tunnel underneath an existing heavy-haul railway tunnel, a model experiment was performed to research the dynamic response characteristics of crossing tunnels. It is found that the under-crossing changes the dynamic response of the existing tunnel and surrounding rock. The acceleration response of the existing tunnel enhances, and the dynamic stress of rock mass between crossing tunnels decreases after the excavation. Both tunneling and the excitation of heavy-haul train loads stretch the tunnel base, and the maximum tensile strain is 18.35 µε in this model test. Then, the measured results were validated by numerical simulation. Also, a parametric study was performed to discuss the influence of the relative position between crossing tunnels and the advanced support on the dynamic behavior of the existing tunnel, where an amplifying coefficient of tunnel vibration was introduced to describe the change in acceleration due to tunneling. These results reveal the dynamic amplifying phenomenon of the existing tunnel during the new tunnel construction, which can be referred in the dynamic design of crossing tunnels.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.153-158
• /
• 2004

The security system using optical fiber is a system, circulating infrared rays laser pulse on the optical fiber which is attached on the security fence to prevent invasion, which can show invasion position with visible and audible signal on the situation monitor if an invader cut or pull the security fence with minuteness of 10m. The optical fiber can be also applied for the bed structure stability monitoring system of high speed train as well as security system. To apply this system for high speed railroad bed structures, this system will give an alarm if it detect excessive tension, shrinkage, deflection which is beyond the limit of structure, that will prevent serious railroad accident. In this paper, we like to propose that applying this system for security and structure stability can improve confidence and stability on operation of railways

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1878-1884
• /
• 2010

Currently in Korea, neutral sections in front of substations and sectioning posts are greatly divided into AC/DC sections and AC/AC sections. Considering catenary damage and safety issues trains pass crossover by coasting driving at notch-off. However in cases of Japan, China, or Taiwan, the usage of automatic crossover system makes it possible to pass at notch-on, enhancing high-speed railway operation for efficiency, and stability. These are the purposes of developing automatic power crossover system in neutral sections. This paper introduces two methods to detect the position of a train required to activate automatic crossover systems in neutral sections. The optimal method is expected in terms of the distance of neutral section.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.2
• /
• pp.163-171
• /
• 2016

In order to detect the exact position of high-speed train, it is necessary to obtain location information from the transponder tag installed along the track. In this paper, we proposed parallel descrambling scheme for high-speed railway transponder system, which aims for reducing the processing time required to decode telegram. Since a telegram is stored in a tag after information bits are scrambled by an encoder, decoding procedure includes descrambling of received telegram to recover the original information bits. By analyzing the structure of the descrambling shift register circuit, we proposed a parallel descrambling scheme for fast decoding of telegram. By comparing the required number of clocks, it is shown that the proposed scheme significantly outperforms the original one.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.158-162
• /
• 2004

The magnetic levitator is the device which can float a magnetic material at the midair by electromagnetic force and it's principle can be applied to the high speed magnetic bearing or magnetic levitation train. There are many difficulties to control, because the magnetic levitator is basically a nonlinear and unstable system. In this paper, this system is modeled assuming that it is a linear system nearby an operating point, and a proportional and derivative(PD) position controller is designed to carry out the variable position control. The performance of position control response is shown through simulation and experiment. A prototype magnetic levitator is constructed using PWM converter and DSP(Digital Signal Processor) based control board.

• International Journal of Railway
• /
• v.5 no.2
• /
• pp.55-64
• /
• 2012

Subject of the paper is a particular configuration of overhead line, in which noise barrier structure is used as supports of the catenary instead of standard poles. This configuration is foreseen in case the noise barrier position is in conflict with the poles location. If the catenary is supported by the noise barrier, the motion that the latter undergo due to wave pressure associated to train transit is transmitted to the overhead line, so that potentially it influences the interaction between the catenary itself and the pantograph of the passing train. The paper focuses on the influence of such peculiar configuration on the quality of the current collection of high speed pantograph, for single and double current collection. The study has been carried out first with an experimental investigation on the pressure distribution on noise barrier, both in wind tunnel and with in-field tests. Subsequently a numerical analysis of the dynamics of the barrier subjected to the wave pressure due to train transit has been carried out, and the output of such analysis has been used as input data for the simulation of the pantograph-dynamic interaction at different speeds and with front or rear pantograph in operation. Consideration of structural modifications was then highlighted, in order to reduce the influence on the contact loss percentage.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.111-117
• /
• 2011

Vibration monitoring is required for reliable thermosonic testing to decide whether sufficient vibration is achieved in each test for the detection of cracks. From a practical point of view, a cheaper and convenient monitoring method is better for the application to real tests. Therefore, the performance of different sensors for vibration monitoring was investigated and compared in this study to find a convenient and acceptable measurement method for thermosonics. Velocity measured by a laser vibrometer and strain provide an equivalent HI when measured at the same position. The microphone can provide a cheaper vibration monitoring device than the laser and the heating index calculated by a microphone signal shows similar characteristics to that calculated from velocity measured by the laser vibrometer. The microphone frequency response shows that it underestimates high frequency components but it is applicable to practical tests because it gives a conservative value of HI.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.98-103
• /
• 2002

In this paper, static analysis of eddy current brake's frame, which is one of key structural components of brake system for high speed train, was performed in order to evaluate the design by computer simulation. Calculation was carried out in general for the driving modes 'braking' and 'frame in upper position(Brakes inactive)'. Several yield stress load cases and fatigue load cases were analysed for each of the driving modes. The fatigue load resulting from the Multi Body System simulation was also taken into consideration. The simulation results shows that some of structural part should be improved for more increasing reliability of frame.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.317.1-317
• /
• 2002

In this paper, static analysis of eddy current brake′s frame, which is one of key structural components of brake system for high speed train, was performed in order to evaluate the design by computer simulation. Calculation was carried out in general for the driving modes "braking" and "frame in upper position(brakes inactive)". Several yield stress load cases and fatigue load cases were analysed fur each of the driving modes. (omitted)