• 한국철도학회논문집
• /
• 제15권3호
• /
• pp.244-250
• /
• 2012

본 논문에서는 차세대 고속철도 구동 인버터 시스템의 고조파로 인한 전자기적 소음을 줄이기 위해 RCF-PWM(Random Carrier Frequency Pulse Width Modulation)을 적용한 인버터 구동시스템을 개발하였다. RCF-PWM 방식은 인버터 스위칭 주파수를 전력용 반도체의 최대 스위칭 주파수와 최소 스위칭 주파수 사이에서 임의적으로 변화시키며 PWM을 수행하는 방법이다. 본 연구의 타당성을 확인하기위해서 RCF-PWM이 적용된 차세대 고속전철 시스템을 설계하여 MATLAB/Simulink 기반의 시뮬레이터를 개발하고 이를 이용하여 일정한 스위칭 주파수를 사용하는 정규적인 SVPWM 방식과 RCF-PWM 방식의 시험결과를 비교 분석하였다.

• 한국정보전자통신기술학회논문지
• /
• 제7권4호
• /
• pp.147-150
• /
• 2014

본 논문은 고속 고출력 레이저 다이오드(Laser Diode: LD) 구동에 사용되는 펄스형 전원장치의 개발에 관하여 논 하였다. 고속 고출력 레이저는 주로 가공기기나 의료기기 등에 응용되고 있어 그 사용 범위가 넓어지는 추세이나 관련된 기술에 대한 연구는 활발히 이루어지지 않은 편이다. 본 연구에서는 고속 고출력 LD의 구동에 적합한 LLC컨버터에 관한 연구를 수행 하였으며 특히 LD의 수명을 고려하여 구동 전류의 주파수를 유지하며 인가되는 전류의 크기를 임계전류를 고려한 방식으로 설계하여 드라이버 설계를 수행하였으며 그 결과를 실험을 통하여 확인하였다.

• 대한전자공학회논문지TC
• /
• 제40권1호
• /
• pp.37-46
• /
• 2003

임의로 결선된 디지털 전송선로의 과도응답을 효율적인 노드분할 기법을 사용하여 분석하였다. 제시한 노드분할 기법은 전송선로를 분할하여 해석할 수 있도록 하므로서 연결선의 임의 위치에서의 과도파형을 쉽게 예측할 수 있다. 일반성을 보이기 위해 임의로 연결된 분산특성을 갖는 마이크로스트립 다도체 전송선로들을 예로 들어 분석하였다. 결합선로의 주파수의존성 등가 회로정수들은 스펙트럼 영역 기법(SDA)을 사용하여 도출하였다. 고속 마이크로스트립 결합선로 상에 인가되는 펄스의 펄스폭 변화가 누화에 미치는 영향도 동시에 검토하였다. 선로의 길이와 기판 유전율이 증가하면 누화 피크값이 단조롭게 증가한다는 기존의 결과와는 달리 펄스폭이 수 ps에 이르면 오히려 감소하는 특성을 볼 수 있었다. 제시한 노드분할 기법을 사용한 결과를 일반화된 S-행렬 기법을 사용한 결과와 비교하므로서 타당성을 보였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.333-333
• /
• 2011

We have investigated the breakdown properties in liquids by high voltage pulse system. High voltage pulse power system is consisted of the Marx-generator with two capacitors (0.5 ${\mu}F$, withstanding voltage is 40 kV), to which the charging voltage can be applied to maximum 30 kV DC, spark gap switch and charging resistor of 20 $M{\Omega}$. We have made use of tungsten pin electrodes of anode-cathode (A-K), which are immersed into the liquids. The breakdown voltage and current signals are measured by high voltage probe (Tektronix P6015A) and current monitor (IPC CM-1.S). Especially the high speed breakdown or plasma propagation characteristics in the pulsed A-K gap have been investigated by using the high speed ICCD camera. We have measured the electron temperature through the Boltzmann plot method from the breakdown spectrums. Here the A-K gap has been changed by 1 mm, 2 mm, and 3 mm. The used liquids are distilled water and solution of salt (0.9 %). The output voltage and current signals at breakdown in distilled water are shown to be bigger than those in saline solution. The breakdown voltage and current characteristics in liquids will be discussed in accordance with A-K gap distances. It is also found that the electron temperatures and plasma densities in liquids are decreased in conformity with A-K gap.

• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.868-876
• /
• 1995

This study deals with a position control of an electro-hydraulic servo system which consist of cylinder and high speed on-off valves operated by microcomputer. The merits of PWM control of hydraulic equipment are the robustness of the high spee on-off valve, its low price and the direct control without D/A converter. In the PWM control of high speed on-off valve, the time lag and switching time existing between the input and output signals of valve are considered as demerit points. To get analytical results, the effects of these demerits have to be clarified in detail. The object of this study is to propose a mathematical model for the behavior of high speed on-off valve and to get analytical results of this system. The dynamic characteristics of this system is examined by digital computer simulation analytically and compared with experimental results to varify the proposed mathematical model.

• 대한기계학회논문집A
• /
• 제32권11호
• /
• pp.943-950
• /
• 2008

A novel nondestructive testing (NDT) system, which is able to detect a crack with high speed and high spatial resolution, is urgently required for inspecting small cracks on express train wheels. This paper proposes a high speed scan type magnetic camera, which uses the multiple amplifying circuits and the crack indicating pulse output system. The linearly integrated Hall sensors are arrayed in parallel, and the Hall voltages from each sensor in the scanning direction are obtained and amplified. High-speed NDT can be achieved by using the exclusive analog-digital converter and micro-processor because the ${\partial}\;V_H/\;{\partial}$ x value, which provides the most important crack information, can be obtained by buffering and calculating. The effectiveness of the novel method was verified by examine using cracks on the wheel specimen model.

• 전기학회논문지
• /
• 제56권8호
• /
• pp.1503-1510
• /
• 2007

To implement a high-precision lightning tracking system utilizing TDOA measurements, high-speed data acquisition and precise timing synchronization between ground sensors should be achieved. At the same time, considering the size of digitizer's memory, the data memory needs to be managed so that only the sampled data around the occurrence of stepped leader pulse is stored. This paper presents a detection-and-acquisition system for lightning signals that is the main equipment of ground sensor in lightning tracking system. GPS clock module is used to get precise timing synchronization and the 500MHz high speed digitizer is employed. In order to detect the leading edge of the lightning pulse and save the sampled data and its timing, lightning detection module is implemented and multi-record method is employed in the proposed system. Field experiment results show that the proposed system can detect and save the lightning signal efficiently.

• Journal of Power Electronics
• /
• 제6권3호
• /
• pp.235-244
• /
• 2006

Recently, speed sensorless vector control for synchronous reluctance motors (SYRMs) has deserved attention because of its advantages. Although rotor angle calculation using flux estimation is a straightforward approach, the DC offset can cause an increasing pure integrator error in this estimator. In addition, this method is affected by parameter fluctuation. In this paper, to control the motor at the low speed region, a modified programmable cascaded low pass filter (MPCPLF) with sensorless online parameter identification based on a block pulse function is proposed. The use of the MPCLPF is suggested because in programmable, cascade low pass filters (PCLPF), which previously have been applied to induction motors, the drift increases vastly wl)en motor speed decreases. Parameter identification is also used because it does not depend on estimation accuracy and can solve parameter fluctuation effects. Thus, sensorless speed control in the low speed region is possible. The experimental system includes a PC-based control with real time Linux and an ALTERA Complex Programmable Logic Device (CPLD), to acquire data from sensors and to send commands to the system. The experimental results show the proposed method performs well, speed and angle estimation are correct. Also, parameter identification and sensorless vector control are achieved at low speed, as well as, as at high speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.235-240
• /
• 2002

In micro-EBM, it is well blown that RC circuit is suitable for discharge circuit because of its low pulse width and relatively high peak current. To increase machining speed without changing unit discharge energy, charge resistance should be decreased. But, if very low, continuous (or normal) arc discharge occurs, then increases electrode wear and reduces machining speed remarkably. In this paper, RC circuit with transistor is used to micro-EDM. Experimental results show that RC circuit with transistor can cut off continuous (or normal) arc discharge effectively if duty factor and switching period of transistor are set up optimally. Through experiments with varying charge resistance, it can be known that RC circuit with transistor has about two times faster machining speed than that of RC circuit. Especially, it has prominent rise-effect of machining speed in low unit discharge energy, so that a high-quality and high-speed micro-EDM can be realized through RC circuit with transistor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.115-118
• /
• 2007

Luminous efficacy of 6.0 lm/W has been realized by introducing a spatial positive column discharge together with delayed D pulses, shared sustain pulse voltage, and low sustain frequency drive. Also a high speed addressing of $0.25{\mu}s$ was achieved. The luminance was $157cd/m^2$, which is high enough for a 260-in. FHD display.