• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.887-890
• /
• 2003

High Speed data transmission over a long length of cable is limited due to the limited bandwidth of a cable which introduces ISI(Inter Symbol Interference). In order to compensate for the loss and phase dispersion in the cable, a pulse shaping in a transmitter and a line equalizer in receiver can be used. This paper presents a low-power and small-ana analog adaptive pulse shaping circuit and line equalizer, The design was fabricated in a 0.25${\mu}{\textrm}{m}$ mixed-signal CMOS process. The proposed pulse shaping circuit and equalizer operate at 400Mb/s on 50m STP(Shielded Twisted Pair) cable. It consumes 28.5${\mu}{\textrm}{m}$ with a 2.5-V power supply and occupies only 0.098 $\textrm{mm}^2$.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.13-21
• /
• 1997

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG Laser welding. A large porosity was formed in a keyhole mode of deep penetration weld metal of any stainless steel. Solidification cracks were present in Type 303 with about 0.3%s. The conditions for the formation of porosity were determined in further detail in Type 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of Type 310S. through high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.4
• /
• pp.347-356
• /
• 1987

This paper is to propose a new line code suitable for a high speed unipolar pulse transmission system, such as a high speed optical digital transmission system. The original information speed can be converted into the transmission speed $\frac{(m+1)}{m}$ by the speed converter. Then this code, named mBiZ code, is generated by means of an Exclusive NOR between the bit stream inserted a space into every m bits and the bit stream delayed by the time slot allocated a single bit at the output coded sequence. Therefore, a mBiZ code can reduce a redundancy in the line code for transmission and its conversion circuits can be devised easily. The mBiZ code can also suppress undesirable long consecuitive identical digits and make line code balance in the mark and space ratio. Therefore, high frequency and low frequency components in power spectrum of a mBiZ code can be suppessed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.412-420
• /
• 2003

This study describes the merits of PWM control of hydraulic system using high speed on-off valves. Generally, Electro-hydraulic valves can be classified into two classification: valves which are controlled by analog signal and which are controlled by digital. The former includes hydraulic servo valves and proportional valves which require A/D converters as interface to digital computer and too costly and sensitive to oil contamination because of complexity in structures. The latter includes high speed on-off valves which do not require A/D converters because they are normally operated in a pulse width modulation(PWM) method, and are low in price and robust to oil contamination because of their simple structures. The objectives of this study is to analyze the limit cycle which regularly appear in the position control system using 2/2way high speed on-off valves and to give a criterion for the stability of this system. The nonlinear characteristics of PWM and cylinder friction of this system are described by harmonic linearization and the effects of parameter variations to the system stability are simulated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.12B
• /
• pp.1244-1250
• /
• 2010

This paper presents a detection and ranging algorithm for a high-speed targets in the high PRF radar. We show, unlike the conventional methods, it firstly estimates Doppler frequency with a quasi-periodic pulse train prior to range processing. The estimated Doppler frequency can compensate the phase error enbeded in the received signal, which makes the signal integrated coherently in the range direction and localizes the target's signiture in low SNR. We present the derivation of the proposed algorithm and discuss how the system parameters such as the range/Doppler sampling condition, processing time and Doppler estimation error affect the performance of the proposed algorithm, which is verified by simulations.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.80-84
• /
• 2011

The weight reduction of the transportations has become an important technical subject Al and Al alloys, especially Al 5052 alloys have been being applied as door materials for automobile. One of the most widely known car weight-reduction methods is to use light and corrosion-resistant aluminum alloys. However, because of high electrical and thermal conductivity and a low melting point, it is difficult to obtain good weld quality when working with the aluminum alloys. Also, Pulse MIG welding is the typical aluminum welding process, but it is difficult to apply to the thin plate, because of melt-through and humping-bead. In order to enhance weld quality, welding parameters should be considered in optimizing the welding process. In this experiment, Al 5052 sheets were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) pulse process. The proper welding conditions such as welding current, welding speed, torch angle $50^{\circ}$ and gap 0~1mm are determined by tensile test and bead shape. Through this study, range of welding current are confirmed from 100A to 120A. And, the range of welding speed is confirmed from 1.2m/min to 1.5m/min.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4B
• /
• pp.245-256
• /
• 2003

2-D OCDMA is considered to be a viable technical solution for optical LANs, and a considerable amount of research effort has been devoted to various 2-D OCDMA techniques. In this paper, we propose two new interference model for 2-D OCDMA LANs employing unipolar random codes, and derive maximum-likelihood detectors based on these interference models. The BER performance of the maximum likelihood detectors and that of other existing detectors are compared through extensive computer simulation. In addition, the complexity of high-speed implementation of the detectors is assessed, and as a result, we found that the AND detector and the maximum-likelihood detectors for the pulse-binomial and the pulse-Poisson model offer the best trade-off between the BER performance and the facility of high-speed implementation.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.44-51
• /
• 2004

In a micro-EDM, it is well known that an RC circuit is suitable as a discharge circuit because of its low pulse width and relatively high peak current. To increase machining speed without changing unit discharge energy, charge resistance should be decreased. But, when the resistance is very low, continuous (or normal) arc discharge occurs, electrode wear increases and machining speed is reduced remarkably. In this paper, an RC circuit with transistors is used in a micro-EDM. Experimental results show that the RC circuit with transistors can cut off a continuous (o. normal) arc discharge effectively if the duty factor and switching period of the transistor are set up optimally. Through experiments with varying charge resistances, it is shown that the RC circuit with transistors has about two times faster machining speed than that of an RC circuit.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.755-760
• /
• 2012

In this study, three dimensional cutting force components and surface roughness appeared in high speed cutting by using tungsten carbide endmill tools implanted ion or not found mutual relations through several analysis of statistical dispersion. It is showed that cutting force(Fx) is affect with spindle speed and feed rate, cutting force(Fy) is affect with spindle speed and ion implantation time and cutting force(Fz) is affect with feed rate in interaction through the statistical method of ANOVA of cutting force and surface roughness, it is analyzed that it is affected of spindle speed and feed rate in surface roughness.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.1-13
• /
• 1998

When driven with a short (less than 30$\mu\textrm{s}$) low-energy pulse, the semiconductor bridge(SCB) produces a hot plasma that ignites explosive. The shape of plasma was observed using ultra high speed camera, the generation and the duration time of plasma were estimated by analyzing the ultra high speed camera image. The more energy supplied, the sooner the formation of the plasma was, and the size of the plasma was increased in proportion. The voltage variation of the bridge was measured and analyzed by comparing with the ultra high speed camera image.