• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1640_1641
• /
• 2009

Dynamic friction and force ripple are the most predominant factors that affect the positioning accuracy of permanent magnet synchronous motor(PMSM) servo drives system, and it is desirable to compensate them in finite time with a continuous control law. In this paper, based on LuGre dynamic friction model, a robust adaptive skidding mode controller is proposed to compensate the nonlinear effect of friction and force ripple. The controller scheme consists of a PD component and a robust adaptive sliding mode controller for estimating the unknown system parameter. Using Lyapunov stability theorem, asymptotic stability analysis and position tracking performance are guaranteed. Simulation results well verify the feasibility and the effectiveness of the proposed scheme for high0precision motion trajectory tracking.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.888-893
• /
• 2005

Since inertial sensor errors which increase with time are caused by initial orientation error and sensor errors(accelerometer bias and gyro drift bias), the accuracy of these devices, while still improving, is not adequate for many of today's high-precision, long-duration sea, aircraft, and long-range flight missions. This paper presents a navigation error compensation scheme for Strap-Down Inertial Navigation System(SDINS) using star tracker. To be specific, SDINS error model and measurement equation are derived, and Kalman filter is implemented. Simulation results show the boundedness of position and attitude errors.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.263-268
• /
• 1999

The most important things to the tube the of the heat exchanger are the precision of t hole position and the quality of the drill face. Nowadays, 6 and 12 spindle multi-drilling machine controlled by CNC or used to drill holes of the tube sheet. The drilling of 12 axes can offer high speover three times as fast as the drilling of axis. However, the drilling of 12 axes h difficulty in controlling many motors to d spindles and assigning a corresponded numbe accurately to each axis. In the past, conventional method to inspect the code the drilling was machining holes on a thin plate previously which resulted in the productivity because it required a h production cost by machining and weldin time. In this thesis, there are two drilling codes different from CNC code. M code is used to control many motors and S code is used to assign a correspondent number for each axis. For increasing the productivity by removing process, this paper is intended to take simulation of the drill machining c including 6 and 12 axis on the persona computer.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2021년도 추계학술발표대회
• /
• pp.756-759
• /
• 2021

본 논문은 기존의 5축 치아가공기나 반도체장비등에 사용하고 있는 회전형 모터의 경우는 엔코더와 리졸버를 사용하고 있다. 엔코더와 레졸버는 고가이므로 실제 산업현장에서 전동기의 위치 센서로는 적용하기가 힘들다. 또한 엔코더와 레졸버와 같은 광학식 위치센서는 그 크기와 내구성에 있어 약점이 있기 때문에 취부 할 때에도 어려움이 있다. 따라서 본 연구에서는 5축치아가공기에 적용하기 위해서 자석가동자를 만들었으며, 이러한 문제점을 해결하는 방안으로 리니어모터를 고정자로 하고 자석플레이트를 이동자로 하는 시스템과 별도의 리니어 스케일을 배제하고 기존의 정현파를 발생하는 2개의 리니어홀센서 및 영구자석을 이용하여 가동자의 절대위치와 이동 위치를 검출할 수 있는 리니어 모터 및 그 제어방법, 안정성 및 신뢰성을 향상시킬 수 있는 자석가동자를 이용하여 구동시 실시간으로 데이터를 확인할 수 있고 제어할 수 있는 모니터링 시스템을 개발하는 연구이다.

• 한국정보통신학회논문지
• /
• 제17권9호
• /
• pp.2227-2232
• /
• 2013

유도제어 시스템 체계개발의 초기단계에는 운용 효과도 도출 및 요구사항 적합성 검토를 통한 체계 개략사양도출을 위해 효과도 분석을 수행한다. 본 논문의 목표는 M&S (Modeling & Simulation)를 활용한 운용 효과도 분석을 통해 고속 무인 수중운동체의 목표점 도달 임무를 위한 체계 요구사항 도출이다. 운용 효과도는 대상 수중운동체의 목표점 도달 정확도로 정의한다. 도달 정확도에 가장 큰 영향을 미칠 것으로 예상되는 변수는 항법센서 성능이다. 본 논문에서는 관성항법센서(Inertial Navigation Sensor, INS)와 도플러 속도 측정 장치(Doppler Velocity Log, DVL)를 이용한 복합항법을 고려하였다. 몬테카를로 수치 시뮬레이션을 통해 항법센서 성능에 대한 효과도 분석을 수행한다. 몬테카를로 수치 시뮬레이션 결과는 CEP(Circular Error Probability)와 분산을 이용한 확률분석을 통해 분석한다. 상용 항법센서 가격을 고려하여 최적의 가격대 성능비를 갖는 항법센서 성능을 제시한다.

• 한국항행학회논문지
• /
• 제26권2호
• /
• pp.85-90
• /
• 2022

본 연구에서는 항공기 체계의 성능을 시험하기 위해 시험 대상 항공기에 실제 위협과 유사한 신호를 고출력으로 송신할 수 있는 위협신호 모의 장치를 설계하였다. 고출력 위협신호 모의장치는 광대역(UHF대역, L대역, S대역, X 대역)의 통신신호, 레이다 신호를 송신하는 것이 가능해야 하며, 추적 레이다와 연동을 통해 항공기에 정확하게 지향하여 신호를 송신하는 제어시스템이 필요하다. 개발된 장비의 신호의 세기는 신호의 종류에 따라서 63 dBm, 93 dBm이상이며, 추적 정밀도는 0.1°이하로 요구되는 전기적/기계적 성능을 모두 만족함을 확인하였고, 추적 레이다 연동을 통해 고출력 위협신호 모의장치의 안테나가 항공기 위치로 신호를 정확하게 지향할 수 있음을 확인하였다.

• 제어로봇시스템학회논문지
• /
• 제20권1호
• /
• pp.101-105
• /
• 2014

For a localization system, the TDOA (Time Difference of Arrival) measurement and AOA (Angle of Arrival) measurement are often used for estimating target's positions. Although it is known that the accuracy of TDOA based localization is superior to that of AOA based one, it may have a poor vertical accuracy in bad geometrical conditions. This paper, therefore, proposes a localization algorithm in which the vertical position is estimated by AOA measurements and the horizontal one is estimated by TDOA measurement in order to achieve high 3D-location accuracy. And this algorithm is applied to a GPS jammer localization systems because it has a large value of the DOP (Dilution of Precision) when the jammer is located far away from the system. Simulation results demonstrate that the proposed hybrid TDOA/AOA location algorithm gives much higher location accuracy than TDOA or AOA only location.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.196-199
• /
• 1998

LDM(Linear DC Motor) are used in high speed, high-precision position control system. Because of these advatages, LDM has already used in the motor of pen-recorder, magnetic-disk devices. Under the limited dimension, we propose the design method of LDM by magnetic circuit. In this paper, a relation between the thrust constant and size of a LDM that is moving coil type with unipolar is described, which is defined as a simple relational equation. To maximize the rate of thrust to the volume of LDM, the magnetic flux density in the yoke is adjusted to the value of magnetic equation. By the magnetic field analysis(FEM), the validity of the equation is confirmed.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1999년도 추계학술대회논문집
• /
• pp.333-344
• /
• 1999

Currently many studies on the unmanned gantry crane for the automated container terminal are accomplished. This is needed for the development of large scale, automation, high speed, unmanned system and information system in port facility. In order to do efficient container handling job in port yard, the automated handling system is well adapted to the job environments and all-season weather, In order to realize the automatic and unmanned system for container handling job, the required functions and main structure system are studied. The major problems of operation of the conventional gantry crane are that the vibration of gantry structure body is occurred by operation and that high-speed and precision position-velocity control and the capability to dope to the external disturbances caused by the wind, rain, fog and job environments. In this paper, the fundamental study for establishment of the concept and the dynamic modelling of the major sub system of the unmanned gantry crane is presented. These studies are useful for design and manufacturing of the new concept model of the unmanned gantry crane for efficient operation of the automated container terminal.

• 한국생산제조학회지
• /
• 제25권6호
• /
• pp.517-521
• /
• 2016

General industrial robots are difficult to use for precision assembly because they are operated based on position control. Their position accuracy is also usually higher than the assembly clearance (several tens of ${\mu}m$). In previous researches, force control was suggested as a robotic assembly solution. However, this method is difficult to apply in reality because of speed and cost problems. The RCC provides high speed, but applications are limited because the compliance is fixed, and it cannot detect an assembly condition during a task. A variable passive compliance device (VPCD) was developed herein. The VPCD can detect the assembly condition during tasks. This device can provide proper compliance for successful assembly tasks. The pneumatic system and the Stewart platform with an LVDT sensor were applied for measuring the displacement and variable compliance, respectively. The concept design and analysis were conducted to prove the effectiveness of the developed VPCD.