• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제22권5호
• /
• pp.538-544
• /
• 2011

This paper presents a compact single balanced diode mixer fabricated using a 0.1 ${\mu}M$ GaAs p-HEMT commercial process for an E-band frequency up/down converter. This mixer includes a LO balun employing a Marchand balun with a good RF performance. In order to improve the port-to-port isolation, a high pass filter and a low pass filter are include in this mixer at the RF and IF ports, respectively. The fabricated mixer with a very compact size of 0.58 mm2(0.85 mm${\times}$0.68 mm) exhibits a conversion loss of 8～12 dB and an input P1dB of 1～5 dBm at the LO power of 10 dBm from 71～86 GHz.

• Journal of Digital Contents Society
• /
• 제14권1호
• /
• pp.35-40
• /
• 2013

The use of slurry with a mix of abrasives and coolant for making Wire Saw in the photovoltaic industry has sharply increased with the semiconductor wafer. In this paper, the slurry was isolated, purified and dried by microwave drying method with high-purity silicon carbide powder obtained through chemical processing. Dried slurry bulk was first pulverized and chemical treatment was applied to produce powder. The produced slurry powder was then analyzed by going through the following analysis; thermal analysis, particle size analyses: SEM shots, elemental analysis, XRF and XRD. The results of this study found the recovery rate of the power obtained though the chemical processing to be higher than the one obtained from mineral processing. The results anticipate infrastructure building and active responses to increasingly stronger domestic and international environmental regulations through the integration and recycling of large amounts of slurry in the photovoltaic industry.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1523-1525
• /
• 2003

Due to the rapid development of wireless networking system, researches on the communication devices are mainly focus on microwave frequency devices such as filters, resonators, and phase shifters. Among them, Film bulk acoustic resonator (FBAR) has been paid extensive attentions for their high performance. In this research, ZnO thin films were deposited by RF-magnetron sputtering on Al/$SiO_2$/Si wafer and then crystalline properties and surface morphology were examined. To measure crystalline structure and surface morphology X-ray diffraction (XRD) and Scanning Electron Microscope (SEM) were employed. It was showed that crystalline properties of ZnO thin films were strongly dependant on the deposition conditions. As increasing the deposition temperature and the deposition pressures, the peak intensities of ZnO(002) plane were increased until $300^{\circ}C$, then decreased rapidly. At the sputtering conditions of RF power of 213 W and working pressure of 15 m Torr, ZnO film had excellent c-axis orientation, surface morphology, and adhesion to the substrate. In conclusion we optimized smooth surface with very small grains as well as highly c-axis oriented ZnO film for FBAR applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제8권2호
• /
• pp.239-244
• /
• 2004

In this paper, we have developed a frequency mixer which can be used as a microwave phase conjugator in the LS band retrodirective antenna system. The mixer as a phase conjugator must have an If signal of which frequency is nearly as high as that of an RF signal, so this fact brings difficulty in the combination of input signals and the design of impedance matching circuit. The circuit configuration is chosen to be of the gate mixer using a pseudomorphic HEMT device. The operating frequencies are 4.00 ㎓, 2.01 ㎓, and 1.99 ㎓ for LO, RF, and IF, respectively. Conversion gain is measured to be 12.5 ㏈ and 1 ㏈ compression point -34 ㏈m at the LO power of -7 ㏈m. The mixer fabricated in this research is the single-ended type, where RF leakage signal appears inevitably at the If port because RF and If frequencies are almost the same. The circuit topology suggested here can be applied directly to the design of balanced-type mixers and phase conjugators.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• 제22권2호
• /
• pp.43-50
• /
• 2022

In this paper, we designed and verified a Far-field measurement system for measuring the performance of an antenna operating in millimeter wave(W-band). For the antenna test, a measurement system should be selected according to the type of antenna, measurement items, measurement environment and period, etc. In the case of near-field measurement, it takes a lot of time because the number of measurement items increases when the antenna has multiple channels or various beams. Such an antenna can reduce the measurement time through Far-field measurement, and only necessary measurement items can be measured. Therefore, this study secured precise alignment of the far-field measurement system using a high-power laser and improved the measurement accuracy by applying a double amplifier system. The designed system was built in the anechoic chamber and verified by comparison with the verified Near-field measurement system.

• Journal of IKEEE
• /
• 제28권1호
• /
• pp.33-37
• /
• 2024

In this paper, we report the design and the measurement of a X-band low noise amplifier (LNA) monolithic microwave integrated circuit (MMIC) using a 0.25 ㎛ gate length microstrip GaN-on-SiC high electron mobility transistor (HEMT) technology. The developed X-band GaN-based LNA MMIC achieves small signal gain of 22.75 dB ~ 25.14 dB and noise figure of 1.84 dB ~ 1.94 dB in the desired band of 9 GHz to 10 GHz. Input and output return loss values are -11.36 dB ~ -24.49 dB and -11.11 dB ~ -17.68 dB, respectively. The LNA MMIC can withstand 40 dBm (10 W) input power without performance degradation. The chip dimensions are 3.67 mm × 1.15 mm. The developed GaN-based LNA MMIC is applicable to various X-band applications.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.68.1-68.1
• /
• 2012

The best part of graphene is - charge-carriers in it are mass less particles which move in near relativistic speeds. Comparing to other materials, electrons in graphene travel much faster - at speeds of $10^8cm/s$. A graphene sheet is pure enough to ensure that electrons can travel a fair distance before colliding. Electronic devices few nanometers long that would be able to transmit charge at breath taking speeds for a fraction of power compared to present day CMOS transistors. Many researches try to check a possibility to make it a perfect replacement for silicon based devices. Graphene has shown high potential to be used as interconnects in the field of high frequency electrical devices. With all those advantages of graphene, we demonstrate characteristics of electrical and optical properties of graphene such as the effect of graphene geometry on the microwave properties using the measurements of S-parameter in range of 500 MHz - 40 GHz at room temperature condition. We confirm that impedance and resistance decrease with increasing the number of graphene layer and w/L ratio. This result shows proper geometry of graphene to be used as high frequency interconnects. This study also presents the optical properties of graphene oxide (GO), which were deposited in different substrate, or influenced by oxygen plasma, were confirmed using different characterization techniques. 4-6 layers of the polycrystalline GO layers, which were confirmed by High resolution transmission electron microscopy (HRTEM) and electron diffraction analysis, were shown short range order of crystallization by the substrate as well as interlayer effect with an increase in interplanar spacing, which can be attributed to the presence of oxygen functional groups on its layers. X-ray photoelectron Spectroscopy (XPS) and Raman spectroscopy confirms the presence of the $sp^2$ and $sp^3$ hybridization due to the disordered crystal structures of the carbon atoms results from oxidation, and Fourier Transform Infrared spectroscopy (FTIR) and XPS analysis shows the changes in oxygen functional groups with nature of substrate. Moreover, the photoluminescent (PL) peak emission wavelength varies with substrate and the broad energy level distribution produces excitation dependent PL emission in a broad wavelength ranging from 400 to 650 nm. The structural and optical properties of oxygen plasma treated GO films for possible optoelectronic applications were also investigated using various characterization techniques. HRTEM and electron diffraction analysis confirmed that the oxygen plasma treatment results short range order crystallization in GO films with an increase in interplanar spacing, which can be attributed to the presence of oxygen functional groups. In addition, Electron energy loss spectroscopy (EELS) and Raman spectroscopy confirms the presence of the $sp^2$ and $sp^3$ hybridization due to the disordered crystal structures of the carbon atoms results from oxidation and XPS analysis shows that epoxy pairs convert to more stable C=O and O-C=O groups with oxygen plasma treatment. The broad energy level distribution resulting from the broad size distribution of the $sp^2$ clusters produces excitation dependent PL emission in a broad wavelength range from 400 to 650 nm. Our results suggest that substrate influenced, or oxygen treatment GO has higher potential for future optoelectronic devices by its various optical properties and visible PL emission.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제19권7호
• /
• pp.727-732
• /
• 2008

Recently, according to the increase of using the microwave equipments, the interests in effects on human body have been also increased. For example, there have been many researches on making the standard the specific absorbing ratio (SAR) caused by mobile phones. However, it is needed to study on the induced current on human body caused by HF(Hight Frequency) band which can deeply penetrate the human body. Especially, since the RFID systems are applied to the transportation card and the library, it is hooded to research on the effect on human body exposed to the radiated power from the RFID system. In this paper, we designed a cylindrical monopole antenna model of human body exposed to 13.56 MHz RFID system, which can model the induced current on human body. To verify the proposed equivalent antenna model, we compared the induced currents between human body and the equivalent antenna model.

• Journal of the Korean Electrochemical Society
• /
• 제8권3호
• /
• pp.139-145
• /
• 2005

[ $SnO_x$ ] films on the flexible substrate of PET film were prepared at ambient temperature under a $(CH_3)_4Sn(TMT: tetra-methyl tin)-H_2-O_2$ atmosphere in order to obtain transparent conductive polymer by using ECR-MOCVD(Electro Cyclotron Resonance Metal Organic Chemical Yfpor Deposition) system. The prepared $SnO_x$ thin films show generally over $90\%$ of optical transmittance at wavelength range of 380-780nm and about $1\times10^{-2\~3}ohm{\cdot}cm$ of electrical resistivity. In the present study, effects of $O_2/TMT\;and\;H_2/TMT$ mole ratio on the properties of $SnO_x$ films are investigated and the other process parameters such as microwave power, magnetic current power, substrate distance and working pressure are fixed. Based on our experimental results, the $SnO_x$ film composition ratio of Sn and O directly influences on the electrical and optical properties of the films prepared. The $SnO_x$ film with low electric resistivity and high transmittance could be obtained by controlling the process parameters such as $O_2/TMT\;and\;H_2/TMT$ mole ratio, which play an important role to change the composition ratio between Sn and O. An increase of $O_2/TMT$ mole ratio brought on the increases 0 content in the $SnO_x$ film. On the other hand, an increase of $H_2/TMT$ mole ratio lead to decreases the oxygen content in the film. The optimized composition ratio of oxygen : tin Is determined as 2.4: 1 at $O_2/TMT$ of 80 and $H_2/TMT$ of 40 mole ratio, respectively.