• Proceedings of the KWS Conference
• /
• 1994.10a
• /
• pp.89-92
• /
• 1994

According to the industrial development welding technology is necessitated to develop in the direction of full automation, high efficiency, energy saving, and full safety. In this study, thus, a simple holder ampere controller for welding systems is developed and applied to arc welders and its capability is examined and tested. The results are as follows: 1. It has a simple structure, since the primary AC power for the welder can be directly control led using a triac. 2. It can control the electric power strength in several steps as well as on and off easily, since a small-sized variable resistance is installed in the small controller on the welding holder. 3. In real field applications a welding system with this controller increases the working efficiency greatly compare to the conventional arc welders without the system, because the controller can control the ampere onsite far from the main power supply. 4. It can reduce the probability of the electrical mishap due to electrical leakage, since the electricity is disconnected as soon as the switch is off or welding person's hand is taken off from the welder after the work or for rest. 5. It can control the welding depth in the beginning and do the crater treatment well in the ending of welding, since it always supplies the relevent amount of electrical current. Therefore, it can improve the mechanical properties of the welding zone.

• Nuclear Engineering and Technology
• /
• v.30 no.4
• /
• pp.342-352
• /
• 1998

A nuclear design feasibility of soluble boron free(SBF core for the medium-sized(600MWe) PWR was investigated. The result conformed that soluble boron free operation could be performed by using current PWR proven technologies. Westinghouse advanced reactor, AP-600 was chosen as a design prototype. Design modification was applied for the assembly design with burnable poison and control rod absorber material. In order to control excess reactivity, large amount of gadolinia integral burnable poison rods were used and B4C was used as a control rod absorber material. For control of bottom shift axial power shape due to high temperature feedback in SBF core, axial zoning of burnable poison was applied to the fuel assemblies design. The combination of enrichment and rod number zoning for burnable poison could make an excess reactivity swing flat within around 1% and these also led effective control on axial power offset and peak pin power, The safety assessment of the designed core was peformed by the calculation of MTC, FTC and shutdown margin. MTC in designed SBF core was greater around 6 times than one of Ulchin unit 3&4. Utilization of enriched BIO(up to 50w1o) in B4C shutdown control rods provided enough shutdown margin as well as subcriticality at cold refueling condition.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2014.01a
• /
• pp.9-13
• /
• 2014

The performance of large scale software applications has been automatically increasing for last few decades under the influence of Moore's law - the number of transistors on a microprocessor roughly doubled every eighteen months. However, on-chip transistors limitations and heating issues led to the emergence of multicore processors. The energy efficient ARM based System-on-Chip (SoC) processors are being considered for future high performance computing systems. In this paper, we present a case study of two widely used parallel programming models i.e. MPI and MapReduce on distributed memory cluster of ARM SoC development boards. The case study application, Black-Scholes option pricing equation, was parallelized and evaluated in terms of power consumption and throughput. The results show that the Hadoop implementation has low instantaneous power consumption that of MPI, but MPI outperforms Hadoop implementation by a factor of 1.46 in terms of total power consumption to execution time ratio.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1642-1649
• /
• 2018

A single-stage flyback LED AC-DC converter based on primary-side control under constant current mode is proposed in this study. The proposed converter features low total harmonic distortion (THD) and high power factor (PF). It also consists of a zero-crossing distortion compensation circuit and a variable duty ratio control compensation circuit to deal with the line current distortions caused by fixed duty ratio control. The system model and layout are built in Simplis and Cadence, respectively. The feasibility and performance of the proposed circuit is verified by designing and fabricating an IC controller in the HHNEC $0.35{\mu}m$ 5 V/40 V HVCMOS process. Experimental results show that the PF can reach a level in the range of 0.985-0.9965. Moreover, the average THD of the entire system is approximately 10%, with the minimum being 6.305%, as the input line voltage changes from 85 VAC to 265 VAC.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.06a
• /
• pp.435-438
• /
• 2009

A navigation aid buoy is a kind of safety facility for maritime navigation with a purpose of leading the vessels for navigating, docking and sail off. An advanced rechargeable battery is required for stable power supply for navigation aid buoy as the high magnitude LED lamps, real time location/control for navigation aids and e-Navigation support systems with maritime climate observation equipments have recently been deployed. This study is focused on the lithium battery, especially lithium polymer battery which is believed to be safer than the other types of batteries. The lithium polymer battery reviewed in this study is designed with $LiFePO_4$-based cathode, which has superior safety features to the oxide-based cathodes. Besides, a 3.6kWh battery pack has been built with the above-mentioned unit cells for the purpose of comparative research with lead acid battery system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.3
• /
• pp.201-206
• /
• 2019

This report constitutes the first demonstration in Korea of single-crystal lateral gallium oxide ($Ga_2O_3$) as a metal-oxide-semiconductor field-effect-transistor (MOSFET), with a breakdown voltage in excess of 480 V. A Si-doped channel layer was grown on a Fe-doped semi-insulating ${\beta}-Ga_2O_3$ (010) substrate by molecular beam epitaxy. The single-crystal substrate was grown by the edge-defined film-fed growth method and wafered to a size of $10{\times}15mm^2$. Although we fabricated several types of power devices using the same process, we only report the characterization of a finger-type MOSFET with a gate length ($L_g$) of $2{\mu}m$ and a gate-drain spacing ($L_{gd}$) of $5{\mu}m$. The MOSFET showed a favorable drain current modulation according to the gate voltage swing. A complete drain current pinch-off feature was also obtained for $V_{gs}<-6V$, and the three-terminal off-state breakdown voltage was over 482 V in a $L_{gd}=5{\mu}m$ device measured in Fluorinert ambient at $V_{gs}=-10V$. A low drain leakage current of 4.7 nA at the off-state led to a high on/off drain current ratio of approximately $5.3{\times}10^5$. These device characteristics indicate the promising potential of $Ga_2O_3$-based electrical devices for next-generation high-power device applications, such as electrical autonomous vehicles, railroads, photovoltaics, renewable energy, and industry.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.3
• /
• pp.105-124
• /
• 2011

TFT-LCD consists of LCD panel on the top, circuit unit on the side and BLU on the bottom. The recent development issues of BLU-dependent TFT-LCD have been power consumption minimization, slimmerization and size maximization. As a result of this trend, LED is adopted as BLU instead of CCFL to increase brightness and to reduce thickness. In liquid crystal displays, the light efficiency is below 10% due to the loss of light in the path from a light source to an LCD panel and presence of absorptive polarizer. This low efficiency results in low brightness and high power consumption. One way to circumvent this situation is to use a reflective polarizer between backlight units and LCD panels. Since a nano-wire grid polarizer has been known as a reflective polarizer, an idea was proposed that it can be used for the enhancement of the brightness of LCD. The use of reflective polarizing film is increasing as edge type LED TV and 3D TV markets are growing. This study has been carried out to fabrication of the nano-wire grid polarizer(NWGP) and investigated the brightness enhancement of LCD through polarization recycling by placing a NWGP between an c and a backlight unit. NWGPs with a pitch of 200nm were fabricated using laser interference lithography and aluminum sputtering and wet etching. And The NWGP fabrication process was using by the UV imprinting and was applied to plastic PET film. In this case, the brightness of an LCD with NWGPs was 1.21 times higher than that without NWGPs due to polarization recycling.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.57-62
• /
• 2011

The VLC (visible light communication) system is communication technology using visible rays (RGB) that come out in LED device. It is energy curtailment effect and possible in ubiquitous network service applications. Also, VLC system has the above advantage about that the communication throughout the whole room is enabled by high power lighting and lighting equipment with white colored LED which are easy to install and have good outward appearance. However, the signal detection performance for the receiver near the network of transmitter boundary is severely degraded and the transmission efficiency decreased due to the influence of the interference signal from the adjacent networks. In this paper, we propose an interference mitigation method with optical beamforming in VLC systems, and evaluate the reception performance. For the system BER, the proposed optical beamforming transmission demonstrates the performance enhancement compared to the not using the optical beamforming scheme, and up to about 5~6dB SNR performance gain is achieved.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.51-56
• /
• 2012

In order to fabricate through-Si-vias for thermal vias by using wet etching process, anisotropic etching behavior of Si substrate was investigated as functions of concentration and temperature of TMAH solution in this study. The etching rate of 5 wt%, 10 wt%, and 25 wt% TMAH solutions, of which temperature was maintained at $80^{\circ}C$, was $0.76{\mu}m/min$, $0.75{\mu}m/min$, and $0.30{\mu}m/min$, respectively. With changing the temperature of 10 wt% TMAH solution to $20^{\circ}C$ and $50^{\circ}C$, the etching rate was reduced to $0.067{\mu}m/min$ and $0.233{\mu}m/min$, respectively. Through-Si-vias of $500{\mu}m$-depth could be fabricated by etching a Si substrate for 5 hours in 10 wt% TMAH solution at $80^{\circ}C$ after forming same via-pattern on each side of the Si substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.237-240
• /
• 2016

The improvement of irradiation intensity and irradiation uniformity is essential for large area and high power UVA light source application. In this study, large number of chips bonded by micro soldering technique were driven by low current, and current limiting diodes were configured to supply constant current to parallel circuits consisting of large number of series strings. The dimension of light source module circuit board was $350{\times}90mm^2$ and 16,650 numbers of 385 nm flip chip LEDs were used with a configuration of 90 parallel and 185 series strings. The space between LEDs in parallel and series strings were maintained at 1.9 mm and 1.0 mm distance, respectively. The size of the flip chip was $750{\times}750{\mu}m^2$ were used with contact pads of $260{\times}669{\mu}m^2$ size, and SAC (96.5 Sn/3.0 Ag/0.5 Cu) solder was used for flip chip bonding. The fabricated light source module with 7.5 m A supply current showed temperature rise of $66^{\circ}C$, whereas irradiation was measured to be $300mW/cm^2$. Inaddition, 0.23% variation of the constant current in each series string was demonstrated.