• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.4
• /
• pp.109-119
• /
• 1998

Recently pipe-framed greenhouses are widely constructed on domestic farm area. These greenhouses are extremely light-weighted structures and so are easily damaged under strong wind due to the lack of uplift resistance of foundation piles. This experiment was carried out by laboratory soil tank to investigate the displacement be haviors of cylindrical pile foundations according to the uplift loads. Tested soils were sampled from two different greenhouse areas. The treatment for each soil type are consisted of 3 different soil moisture conditions, 2 different soil depths, and 3 different soil compaction ratios. Each test was designed to be repeated 2 times and additional tests were carried out when needed. The results are summarized as follows : 1. When the soil moisture content are low and/or pile foundations are buried relatively shallow, ultimate uplift capacity of foundation soil was generated just after begining of uplift displacement. But under the high moisture conditions and/or deeply buried depth, ultimate up-lift capacity of foundation soil was generated before the begining of uplift displacement. 2. For the case of soil S$_1$, the ultimate uplift capacity of piles depending on moisture contents was found to be highest in optimum moisture condition and in the order of air dryed and saturated moisture contents. But for the case of soil S$_2$, the ultimate uplift capacity was found to be highest in optimum moisture condition and in the order of saturated and air dryed moisture contents. 3. Ultimate uplift capacities are varied depending on the pile foundation soil moisture conditions. Under the conditions of optimum soil moisture contents with 60cm soil depth, the ultimate uplift capacity of pile foundation in compaction ratio of 80%, 85%, and 90% for soil 51 are 76kg, 115kg, and 155kg, respectively, and for soil S$_2$are 36kg, 60kg, and 92kg, respectively. But considering that typical greenhouse uplift failure be occurred under saturnted soil moisture content which prevails during high wind storm accompanying heavy rain, pile foundation is required to be designed under the soil condition of saturated moisture content. 4. Approximated safe wind velosities estimated for soil sample S$_1$and S$_2$are 32.92m/s and 26.58m/s respectively under the optimum soil condition of 90% compaction ratio and optimum moisture content. But considering the uplift failure pattern under saturated moisture contents which are typical situations of high wind accompanying heavy rain, the safe wind velosities for soil sample S$_1$and S$_2$are not any higher than 20.33m/s and 22.69m/s respectively.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.3
• /
• pp.199-206
• /
• 2017

A geological repository for the disposal of high-level radioactive waste is generally constructed in host rock at depths of 500~1,000 meters below the ground surface. A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. The buffer is indispensable to assure the disposal safety of high-level radioactive waste, and it can restrain the release of radionuclides and protect the canister from the inflow of groundwater. Since high temperature in a disposal canister is released to the surrounding buffer material, the thermal properties of the buffer material are very important in determining the entire disposal safety. Even though there have been many studies on thermal conductivity, there have been only few studies that have investigates the specific heat capacity of the bentonite buffer. Therefore, this paper presents a specific heat capacity prediction model for compacted Gyeongju bentonite buffer material, which is a Ca-bentonite produced in Korea. Specific heat capacity of the compacted bentonite buffer was measured using a dual probe method according to various degrees of saturation and dry density. A regression model to predict the specific heat capacity of the compacted bentonite buffer was suggested and fitted using 33 sets of data obtained by the dual probe method.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.4
• /
• pp.77-92
• /
• 2021

The energy density of lithium-ion batteries (LIBs) determines the mileage of electric vehicles. For increasing the energy density of LIBs, it is necessary to develop high-capacity active materials that can store more lithium ions within constrained weight. The rapid progress made in cathode technology has realized the utilization of the near-theoretical capacity of cathode materials. In contrast, commercial LIBs have still exploited graphite as active material in anodes since the 1990s. The most promising way to increase anodes' capacity is to mix high-capacity and long-cycle-life silicon oxides (SiOx) with graphite. However, the low initial Coulombic efficiency (ICE) of SiOx limits its content below 15 wt%, impeding the capacity increase in anodes. To address this issue, various prelithiation techniques have been proposed, which can improve the ICE of high-capacity anode materials. In this review paper, we introduce the principles and expected effects of prelithiation techniques reported so far. According to the reaction mechanisms, the strategies are categorized. Mainly, we focus on the recent progress of solution-based chemical prelithiation methods with commercial viability, of which lithiation reaction occurs homogeneously at liquid-solid interfaces. We believe that developing a cost-effective and mass-scalable prelithiation process holds the key to dominating the anode market for next-generation LIBs.

• Computers and Concrete
• /
• v.25 no.6
• /
• pp.525-535
• /
• 2020

The use of pile foundations has become more popular in recent years, as the combined action of the pile cap and the piles can increase the bearing capacity, reduce settlement, and the piles can be arranged so as to reduce differential deflection in the pile cap. Piles are relatively long, slender members that transmit foundation loads through soil strata of low bearing capacity to deeper soil or rock strata having a high bearing capacity. In this study analysis of pile cap with considering different parameters like depth of the pile cap, width and breadth of the pile cap, type of piles and different types of soil which affect the behaviour of pile cap foundation is carried out by using Finite Element Software ANSYS. For understanding the settlement behaviour of pile cap foundation, parametric studies have been carried out in four types of clay by varying pile cap dimensions with two types of piles namely normal and under-reamed piles for different group of piles. Furthermore, the analysis results of settlement and stress values for the pile cap with normal and under-reamed piles are compared. From the study it can be concluded that settlement values of pile cap with under-reamed pile are less than the settlements of pile cap with normal pile. It means that the ultimate load bearing capacity of pile cap with under-reamed piles are greater than the pile cap with normal piles.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1299-1304
• /
• 2014

The electrochemical performance of Li-S cells was investigated in various ternary electrolyte solutions composed of 1,2-dimethoxyethane (DME), tetra(ethylene glycol) dimethyl ether (TGM), and 1,3-dioxolane (DOX). The discharge capacity values and cycle data obtained at each composition were statistically treated with the Minitab program to obtain mixture contour plots, from which the optimal composition of the ternary solvent systems was predicted. The discharge capacities and capacity retention were quite dependent on the electrolyte composition. It was estimated from the contour plots of the capacity at 1.0 C that the discharge capacity sharply increased with a decrease in the TGM content. High capacities greater than 900 mAh/g at 1.0 C were expected for the electrolyte composition with a volume ratio of DME/TGM/DOX = 1/0/1. In contrast, it was predicted from the mixture contour plot of the capacity retention that the cycle performance would significantly increase with an increase in the DME content.

• Textile Coloration and Finishing
• /
• v.23 no.3
• /
• pp.210-218
• /
• 2011

The structure of kapok fiber was characterized using FTIR and $^{13}C$-NMR spectrometers, elemental analyzer, x-ray diffractometer, SEM and IMT I-Solution ver 7.5. The kapok has a hollow tube shape and is composed of cellulose I with crystallinity of 47.95%. To develop novel oil-sorbent materials necessary to avoid the environmental pollution by spilled oil, the oil absorption capacity of various fibers such as kapok, polypropylene(PP), acryl, bamboo, cotton, rayon and wool fibers is compared in this study. The kapok fiber had the highest oil absorption capacity among the fibers and its water absorption capacity was the least. The kapok fiber selectively absorbed significant amounts of oils (43g/g of fiber for kerosene, 65g/g of fiber for soybean oil), which might be due to higher hydrophobicity of the kapok fiber, suggesting that kapok fiber may have high potential as excellent oil-absorbent materials.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.3
• /
• pp.197-204
• /
• 1995

In recent work, we reported that a hot-rolled Fe-18wt%Mn alloy exhibited high damping capacity as well as excellent mechanical properties. It was also proposed that damping capacity of the alloy was proportional to the ${\gamma}/{\varepsilon}$ boundary area. In the present study, the effects of homogenization(12hrs at $1100^{\circ}C$) and solution treatment(1hr at $1050^{\circ}C$ before air cooling) on damping capacity and mechanical properties were investigated for as-cast and heat treated Fe-18wt%Mn alloy. The specimen subjected to both homogenization and solution treatment was found to show superior damping capacity and mechanical properties to the as-cast state due to removal of segregation and increase in ${\gamma}/{\varepsilon}$ boundary area.

• 한국경영정보학회:학술대회논문집
• /
• 2008.06a
• /
• pp.525-540
• /
• 2008

With the competitive pressure and the development of information and communication technology, many organizations have introduced various kinds of enterprise-wide systems like enterprise resource planning (ERP) systems as strategic tools for the purpose of improving organizational performance. Despite their promised strategic benefits, however, their implementation has suffered from a high failure rate and difficulty in realizing the anticipated benefits. Previous studies have indicated that one of the most critical failure reasons is the lack of knowledge sharing and utilization across organizations. As a consequence, many information systems (IS) researchers have paid attention to examining the effect of absorptive capacity closely associated with knowledge sharing and transferring on IS usage performance. ERP systems implementation involves changes not only in systems but also in processes and other social dimensions, which can be related to organizational citizenship behavior (OCB) requiring appropriate communications and interactions among organizational members. A lack of communications and interactions due to a lack of OCB might lead to weak absorptive capacity and thus negatively influence knowledge sharing across organizations, because OCB facilitates a successful collaboration among functional units and positively impacts individual's attitude toward radical organizational change. With this motivation, this study has two research objectives. First, it introduces and tests a theoretical model accounting for the relationships among performance of ERP system usage, absorptive capacity, and OCB. Second, it examines a mediating role of absorptive capacity between OCB and performance of EPR system usage. Theoretical and practical implications of the study ware discussed, along with its limitations.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.765-768
• /
• 2009

In this work, we prepared the activated multi-walled carbon nanotubes (Acti-MWNTs) with well developed physical surface structures, high specific surface area, and higher adsorption capacity by a physical activation process, in order to enhance the hydrogen storage capacity. The Acti-MWNTs' changes in the crystalline phase and in their lattice distortions were characterized by X-ray diffraction (XRD). The textural properties of the Acti-MWNTs were investigated by a nitrogen adsorption isotherms by Brunauer-Emmett-Teller (BET) equation and Harvath-Kawazoe (H-K) calculation, respectively. The hydrogen storage capacity of the Acti-MWNTs was investigated by BEL-HP at 298 K/100 bar. The hydrogen storage capacity of the Acti-MWNTs was improved with the physical activation, resulted from the formation of new hydrogen-favorable sites on the Acti-MWNT surfaces. In conclusion, the physical activation was one of the effective method to enhance the hydrogen storage capacity of the MWNTs.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.52-58
• /
• 2009

In this paper, we propose a probability method to determine minimum capacity of energy storage system(ESS) for Micro-grid Because of high capital cost of ESS, It's very important to determine optimal capacity of ESS and for stable operation of Micro grid(MG), we should determine minimum capacity of ESS. The proposed method has abilities to consider forced outage rate of generators and intermittent of non-dispatchable generators and minimum capacity make MG keep energy balancing by oneself.