• Proceedings of the Safety Management and Science Conference
• /
• 2009.04a
• /
• pp.153-165
• /
• 2009

It is hot issue to get the competitiveness of product through reliability-growth as well as availability and safety in almost high-technology industry including military, chemistry, nuclear, telecommunication, transportation service and so on. In advanced countries, they experienced remarkable growth based on reliability technology in materials&parts industry as well as high-tech industry. It has become a symbol of national competitiveness and created a higher value added. This paper is taking on effectively developing ways to deploy IEC 60300 dependability management system and the base technology that are needed to improve competitiveness of industries in Korea.

• Transactions of Materials Processing
• /
• v.12 no.5
• /
• pp.421-432
• /
• 2003

The dies & molds are a very economical production tool and a high value-added product because of its mass production capability compared to other production methods. Due to the very stiff international competitiveness, the industries meet many obstacles. For the promotion of the industry, the status and the international trends of the industry are measured. The vision and strategy are driven. In Korea, large portion of dies and molds are still low value-added and make large number of tools. In order to advance this industry to the high-tech area and gain competitiveness in the global marketplaces, effective means of resource investment and strategy should be properly provided.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.1-7
• /
• 2017

This study investigates the high-frequency heat treatment characteristics with the distance between a coil and SCM440 parts for an automobile. Global automobile makers are focusing on research to develop high-performance automobiles with improved fuel efficiency and lower emissions in accordance with consumer demand and environmental policies. However, most research on high-frequency heat treatment has been experimental, and it is very difficult to obtain high-frequency heat treatment conditions for a specific product. Therefore, all the conditions of high-frequency heat treatment except the distance between a coil and SCM440 parts were kept the same. As a result, the optimized distance between the coil and SCM440 parts was observed to be 1-2 mm. When the distance between the coil and SCM440 parts was over 3 mm, the effective case hardness depth and total case hardness depth did not satisfy the standards.

• Journal of the Korean association of regional geographers
• /
• v.18 no.4
• /
• pp.400-413
• /
• 2012

The purpose of this study was to look into the formation process and characteristics of local high-tech industrial complex with an example of the Ochang Scientific Industrial Complex and analyzed the characteristics by business type and size, transfer process of the companies in the Complex. For this purpose, statistical data of the companies were analyzed and a survey of them was conducted, and the following results were obtained. First, the Ochang Scientific Industrial Complex was created for agglomeration of IT industries in early days but now there are IT industries and BT industries mixed due to internal and external economic condition. Second, there are more small and medium companies than large companies in the Ochang Scientific Industrial Complex. These companies are in the stage of developing new products and marketing, and many of them were parts and materials developers of core technology or high innovation with venture identification. Third, high rates of the companies in the Ochang Scientific Industrial Complex came from the capital area and the Chungcheong area and the companies which moved in the Complex with their head quarters accounted for more than 70 percent. Fourth, the companies were classified into 5 types according to the type of product and the level of technical innovation.

• Design & Manufacturing
• /
• v.15 no.3
• /
• pp.1-6
• /
• 2021

An artificial neural network model based on a deep learning algorithm is known to be more accurate than humans in image classification, but there is still a limit in the sense that there needs to be a lot of training data that can be called big data. Therefore, various techniques are being studied to build an artificial neural network model with high precision, even with small data. The transfer learning technique is assessed as an excellent alternative. As a result, the purpose of this study is to develop an artificial neural network system that can classify burr images of light guide plate products with 99% accuracy using transfer learning technique. Specifically, for the light guide plate product, 150 images of the normal product and the burr were taken at various angles, heights, positions, etc., respectively. Then, after the preprocessing of images such as thresholding and image augmentation, for a total of 3,300 images were generated. 2,970 images were separated for training, while the remaining 330 images were separated for model accuracy testing. For the transfer learning, a base model was developed using the NASNet-Large model that pre-trained 14 million ImageNet data. According to the final model accuracy test, the 99% accuracy in the image classification for training and test images was confirmed. Consequently, based on the results of this study, it is expected to help develop an integrated AI production management system by training not only the burr but also various defective images.

• Resources Recycling
• /
• v.24 no.2
• /
• pp.62-68
• /
• 2015

The high pure tin production was conducted from crude-tin containing waste solder by electro-refining process. The electro-refining process maintained at 0.2V produced tin with purity of 99.98%, whereas a little increase of voltage to 0.3 V resulted tin purity of 99.92%. The high pure tin of 3N in the present process was produced by fixing the voltage at 0.3V. Considering the high pure tin production, the current density was maintained within $100-120A/m^2$ with current efficiency of 94%. Addition of sulfuric acid of 20 ~ 25 g/L to the electrolyte solution was performed in order to keep Pb (lead) concentration below 100 mg/L in the final tin product. The anode slime generated during electro refining process was analyzed by X-ray diffraction (XRD) study to understand the phases of impurities in it. It detected the presence of Cu and Ag in the slime as in the form of $Cu_6Sn_5$, $Ag_3Sn$, whereas Pb occurred as $PbSO_4$ compound.

• The Journal of Information Technology
• /
• v.1 no.2
• /
• pp.195-208
• /
• 1998

Domestic corporation in High-tech industry invest huge amounts of economic resources into the Research & Development(R&D) department, especially into new product development. It might be an adequate explanation for this phenomena that as the product life cycle gets shorter, and environmental uncertainty necessitates core competency from every corporation, new product planning becomes a vital going concern for the company to keep and increase its market share This could originate from an inappropriate combination between new products and other marketing mix elements. But it could be that the main cause of these failures com from unsatisfactory customers. In the other words, R&D department failed to sufficiently recognize market needs. This could be solved through integration between marketing department R&D department This study supposes that integration between these two departments-marketing department and R&D department influences the success of new product. In other to prove this, this study examined the determinant factors which influence the integration and the relationships

• Journal of the Korea Furniture Society
• /
• v.27 no.3
• /
• pp.237-245
• /
• 2016

Single households currently account for 26.5% of all households and their number is expected to continue to rise, reaching 34.5% by 2035. An analysis of the consumption trends and needs of single households shows that they are rising as a new consumer group with a focus on investment on the individual and favouring: small but high-tech products: efficient use of limited resources: safety and peace of mind: self-improvement and leisure. Products which meet such demands are having an impact on the growth of home-furnishing market. An analysis of companies in Korea's home-furnishing market, with examples like the lifestyle company IKEA, shows a variety of brands such as SPA brand, furniture specialist, distributor and character products. And yet most are OEM products which lack differentiated product lines and compete with similar display and distribution structure. We needs the Single household consumption tendency of home-furnishing market and differentiation strategy through product analysis. In order to increase the value of companies in the home-furnishing market, in addition to differentiated design, product competitiveness must aspire to higher customer satisfaction with easy assembly, innovation in logistics, innovative sales methods such as virtual-reality simulation for products and space, individually-tailored furniture for the needs of single household and products which combine smart technology. For home-grown home-furnishing brands to have competitiveness, they must leverage on the strengths of the industry, offering differentiated and competitive products in a wider range of areas with convergence functions as well as differentiation in consumer interface and application of advancing technology; in-depth product research is called for.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.2963-2968
• /
• 2011

Plastic injection products have been widely used in various electronic appliances and high-tech commodities. However, plastic injection product manufacturers have to spare no efforts to shorten new product development period to introduce new products into the market ahead of other competitors, gaining competitiveness and satisfying customers. The manufacturers cannot only get big target market share rapidly but also the advantage of leading the product price in order to survive in highly competitive market. This paper proposes the cost estimation approach of feature-based plastic injection products by using hybrid artificial neural network and genetic algorithm. The proposed method is to dramatically simplify and shorten the complex conventional cost estimation procedures and the requested computation parameters of plastic injection products. The case study demonstrates the efficiency and effectiveness of the proposed model in solving the cost estimation problem of plastic injection products at the development stage.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.3
• /
• pp.56-65
• /
• 2006

It is well known and widely accepted that the conceptual design is the most influential step in the design process of a product or a system and that about 75% of the life cycle cost is committed as the results of this stage. The purpose of this paper is to present and demonstrate the step of ICDM(Integrated, Customer Driven, Conceptual Design Method) for the development of a ground launcher system, TEL(Transporter, Erector and Launcher). The results of the study show the effectiveness of the method during the conceptual design phase of new complex systems or high-tech products.