• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.157-164
• /
• 2000

This study is about predicting the interior pressure level of the korean high speed train using ray acoustic method. The motor car and the motor and passenger cabin are investigated under the environment of passing open countryside and inside tunnel of 350 km/hr. Calculated sound levels are compared with the proposed sound levels and suggestions about the transmission Joss values of isolating panels inside motor car and the guide lines of allowed sound power limit of motor equipments are provided. Results of TPI car show calculated interior sound level is below the proposed values for both cases of open countryside running and inside tunnel. Since ray acoustic method calculated only air borne noise component, real sound level of the motor car may be higher than prediction. Passenger cabins of TMI, TM5 show higher sound level than the proposed values, so window method was carried out to find the contribution of each panel components and point out the remedy of transmission path. Reduction of sound power of motor equipments should be condisered at the same time.

• Journal of the Korean Society for Railway
• /
• v.8 no.4
• /
• pp.348-353
• /
• 2005

In designing the structures of railway rolling stocks, deterministic methods associated with the concept of a safety factor have been traditionally used. The deterministic approaches based on the mean values of applied loads and material properties have been used as safety verification for the design of rolling-stock car body structures. The uncertainties in the applied loading for the high speed train and the strength of new materials in the rolling stocks require the application of probabilistic approaches to ensure fatigue safety in the desired system. Pressure loadings acting on the car body when the train passes through tunnels show reflected pressure waves for high-speed trains and they may cause a fatigue failure in vehicle bodies. Use of new material technology as body structures also introduces uncertainties in the material strength. A probabilistic approach is more adaptable in designing reliable structures when the pressure waves from the tunnels pounds and new material technology is adopted. In this paper, it is proposed that a fatigue design and assessment method based on a reliability which deals with the loading variations on a railway vehicle due to the pressure reflected in tunnels and the strength variations of material. Equation for the fatigue reliability index has been formulated to calculate the reliability assessment of a vehicle body under fluctuating pressure loadings in a tunnel. Considered in this formulation are the pressure distribution characteristics, the fatigue strength distribution characteristics, and the concept of stress-transfer functions due to the pressure loading.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.391-397
• /
• 2011

In this paper, the pressure endurance test of passenger train's glass window which was developed for next high speed train was studied. At first, pressure test equipment which will be able to generate the maximum pressure same as crossing case between two trainsets in the tunnel was developed. Afterwards the pressure test and evaluation that are based on NFF31-314 were carried out and studied.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.786-791
• /
• 2007

Aerodynamically generated noise is dominant when the train speed approaches 300km/h. This noise sources is caused by the turbulent flow separations or vortex shedding from the train structure. Experiments were performed to investigate the characteristics of aerodynamic noise sources generated from exterior of the KTX trains and HSR-350x, especially from the inter-coach spacing. Measurements of both the inside and outside of the cabin are carried out to investigate the characteristics of the noise. Effect of the size of the mud-flap has been investigated through an wind tunnel test and it has been found that the low frequency noise is strongly dependent on the size of the gap. Also performed is an array measurement to locate different noise sources from the high-speed train. spectral characteristics of exterior noise sources are examined.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.1
• /
• pp.26-33
• /
• 2012

Competition between air transportation and railways has grown fiercer in major countries around the world with the rise of high-speed railways. In South Korea, air passenger travel has been rapidly decreasing since the initial launch of the Seoul-Pusan KTX line in 2004 and second opening that followed in 2010. Further expansion of the high-speed railway is expected. At present, research efforts to verify the validity of constructing an underwater express railway tunnel between Ho-nam and Jeju Island are taking place. Considering the possible high speed railway connection between Seoul and Jeju Island, this thesis has analyzed the choice behavior of existing passengers of the major and low-cost carriers. For this, Stated Preference (SP) research has been performed for three variables, including fare, travel time and the number of runs, to estimate the substitution rate of each of the three variables. Binomial Logit Model has been estimated with the obtained data. The estimation of the model has found that airline passengers of major and low-cost carriers are willing to pay approximately 7,200 KRW and 5,000 KRW, respectively, to reduce travel time by one hour. If the number of runs in one day increases, it has been estimated that the passengers are willing to pay additional fares of about 390 KRW and 30 KRW, respectively. On the other hand, the substitution rate between the number of runs and the travel time was found to be somewhat insignificant. If the construction of the Seoul-Jeju line progresses in the future, this study could be used as preliminary data for determining fares, travel time and the number of runs.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.275-280
• /
• 2003

The Korean high speed train is designed to run at very high speed such as 350km/h. At this time, ballast in roadbed is dispersed by high speed air flow and this hits the substructure of the train. It becomes the factor of damaging the train. To investigate the main factor and possibility of ballast dispersion, the substructure flow is measured by Kiel-Probe Array System at G7 train experiment. And the wind tunnel experiment is performed with ballast in our research. Also CFD analysis is performed by assuming that the flow field is 2D and using simple shaped cross-tie and flat substructure of the train. By comparing the experimental results and CFD analysis, the accuracy of the analysis is checked. They will become the basic research data for the analysis and optimization of train substructure to prevent the ballast dispersion.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.563-575
• /
• 2000

This study was carried out about the system engineering, the design, and Mock-up for the development of passenger car of Korean High Speed Train of maximum operating speed of 350km/h. The design was studied to carbody section ＆ lay out, ring, fitting, carbody, electrical system based on Korean-TGV. The design of aluminium alloy carbody which was enabled to reduce the weight of carbody structure and was studied with construction of air-tightness. Air pressure controlled system provided to comfort passenger due to a reduction of difference pressure between inside and outside of passenger room on running of the tunnel. The Interior design was performed in order to satisfy high speed and comfort to study by the modern design. The electrical system was designed two parts of logic and network for high reliability of train.

• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.167-174
• /
• 2009

Due to the travelling of the train with high speed the period of maintenance activities of the ballasted track is coming to be short, and more from the residential area of the ballasted track tunnel circumference the civil appeal is increasing with railroad vibration problem. To reduce the vibration problem and a maintenance cost establishes the ballast mat in the tunnel within part segment. In this study, to estimate the vibration reduction effect of the ballast mat we have done a comparative analysis with the vibration field test by the transit train by at the ballasted track with ballast mat and the standard ballasted track without vibration protection in tunnel.

• Magazine of korean Tunnelling and Underground Space Association
• /
• v.1 no.2
• /
• pp.59-71
• /
• 1999

Recently, many deformations in tunnel such as crack and leakage were occulted. Specially, the defects of tunnel lining have been a serious problem in safety and stability many repair works for maintenance in tunnel have been carried out. Therefore, it is necessary to estimate the structural cracking for countermeasure in deformed tunnel and to investigate on the characteristics of lining system and the soundness of tunnel. In this study model tests for tunnel lining were carried out using test apparatus and centrifuge, In the direct loading test, the prototype was Kyungbu high-speed railway tunnel and the scale is 1/10, and lining models were made of concrete. Test conditions included load conditions such as direction, shape and type, lining conditions such as single and double lining, thickness, and reinforcement. In centrifuge model test, the prototype was Seoul subway tunnel and the scale is 1/100, and lining models were made of aluminum and hydrostone. Test conditions included tunnel defects such as thickness shortage. behind cavity and longitudinal cracks, reinforcement methods such as epoxy, grouting and carbon sheet. From these model tests , the characteristics of deformation and failure for tunnel lining were estimated, and the structural behaviors of deformed lining and the effects of repair and reinforcement for tunnel lining were researched.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.563-563
• /
• 2013

Railway noise has been a social issues nowadays in our community. This paper discusses the environmental noise problem along railway lines. We overview the noise level and noise exposed populations due to conventional and high speed train operation at first. Then we introduce variety of noise reduction schemes to protect the community based on an engineering approach. Some applicationcases to reduce the noise will be demonstrated. Finally, we propose the noise barrier tunnel as a tool of a generic solution to reduce the community noise along railway lines.