• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.3
• /
• pp.193-197
• /
• 2009

In this paper, we study on design of vehicle control system which is based on ${\mu}C/OS-II$, We component a electric motor drive system for simulator because the most of vehicle part use electric motor for actuator. We use the XC2287 microcontroller which is often used vehicle body controller because XC2287 guarantee high confidence and durability in vehicle industry. The electric motor control system derive PWM from general I/O port in XC2287 microcontroller. The signal is supplied at electric motor after amplifying that using driver circuit. The user control duty of PWM signal through controlling potentiometer which is connected to XC2287. through that, the user control speed of electric motor. we synchronize both input process via controlling potentiometer and PWM output process using semaphore. we verify porting of ${\mu}C/OS-II$ via experimentation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.10
• /
• pp.65-72
• /
• 2000

In this paper, we propose an efficient technique to minimize the input offset of a dynamic latch comparator. We analyzed offset due to charge injection mismatching and unwanted positive feedback during sampling phase. The last one was only considered in the previous works. Based on the analysis, we proposed a modified dynamic latch with initialization switch. The proposed circuit was simulated using 0.65${\mu}m$ CMOS process parameter with 5v supply. The simulation results showed that the input offset is less than 5mV ant 200MHz sampling frequency and the input offset is improved about 80% compared with previous work in $5k{\Omega}$ input resistance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.415-422
• /
• 2004

DSRC provides high speed radio link between Road Side Equipment and On-Board Equipment within the narrow communication area. In this paper, a 5.8 GHz down-conversion mixer for DSRC communication system was designed and fabricated using 0.8 ${\mu}{\textrm}{m}$ SiGe HBT process technology and RF/LO matching circuits, RF/LO input balun circuits, and If output balun circuit were all integrated on chip. The chip size of fabricated mixer was 1.9 mm${\times}$1.3 mm and the measured performance was 7.5 ㏈ conversion gain, －2.5 ㏈m input IP3, 46 ㏈ LO to RF isolation, 56 ㏈ LO to IF isolation, current consumption of 21 mA for 3.0 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1A
• /
• pp.80-86
• /
• 2010

This work has been measured and analyzed the device degradation of NBTI (Negative Bias Temperature Instability) stress induced the increase of gate-induced-drain-leakage(GIDL) current for p-MOS transistors of gate channel length 0.13 [${\mu}m$]. From the relation between the variation of threshold voltage and subthreshold slop by NBTI stress, it has been found that the dominant mechanism for device degradation is the interface state generation. From the GIDL measurement results, we confined that the EHP generation in interface state due to NBTI stress led to the increase of GIDL current. As a results, one should take care of the increased GIDL current after NBTI stress in the ultra-thin gate oxide device. Also, the simultaneous consideration of reliability characteristics and dc device performance is highly necessary in the stress parameters of nanoscale CMOS communication circuit design.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.350-357
• /
• 2005

DSRC provides high speed radio link between Road Side Equipment and On-Board Equipment within the narrow communication area. In this paper, a 5.8 GHz up-conversion mixer for DSRC communication system was designed and fabricated using 0.8 m SiGe HBT process technology and IF/LO/RF matching circuits, IF/LO input balun circuits, and RP output balun circuit were all integrated on chip. The chip size of fabricated mixer was $2.7mm\times1.6mm$ and the measured performance was 3.5 dB conversion gain, -12.5 dBm output IP3, 42 dB LO to If isolation, 38 dB LO to RF isolation, current consumption of 29 mA for 3.0 V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.219-226
• /
• 2000

In this paper, we design and implement a IF(intermediate frequency) module for WLL(wireless local loop) CDMA(code division multiple access) basestation. The implemented IF transceiver is consists of transmitter, receiver and local oscillator. The considered signal bandwidth is 10 MHz and the local carrier frequency is 40 MHz. As test results, the If transmitter output power is -5dBm $\pm3dB$when the baseband input is -10dBm $\pm3dB$, and the IF receiver output power is -10dBm $\pm3dB$when the IF input is -5dBm $\pm3dB$. Also the AGC(automatic gain control) circuit has dynamic range of 9 dB from -7dBm to +2dBm with output power 2dBm. And the group delay characteristic is analyzed by comparing the phase delay from 1 MHz to 5 MHz and the phase distortion is very low. We can conclude that this IF system can be applied to high speed data rate communication system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.11a
• /
• pp.161-166
• /
• 1999

The global trends of mobile communication system is moving toward digitizing, high-speed and large-capacity. Also, to utilize the limited frequency-resource efficiently, spread spectrum system is a mainstream. In this study we are concerning with the fast frequency-hopping system. Instead of the PLL with many problems such as phase-noise, we used the DDS is popular in these days minimizes the disadvantage of PLL. In the case the FFH system is designed using the PLL, it is difficult to be satisfied of the design conditions such as RF badwidth and the settling time of PLL, and it has limitation because of complex circuit by using the balanced modulator. In this study, we evaluated the performance in order to design the FFH system using the DDS. The system that has the improvement of error rate, 1Mhps hopping rate and 5MHz RF bandwidth is designed and evaluated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.4
• /
• pp.278-286
• /
• 2008

This paper investigates the fault generation type and the cause of output interruptionsin bulky with $30^{\sim}500[KVA]$ double conversion UPS, and proposes the fault detection method to improve the reliability of power supply used in the critical load in industry. Identifies its existing way of detecting a quality of inverter output it to bypass when exceeds its expectation. Under a UPS managing system, when an inner (Power device, Controller, CPU) fault occurs it disrupts the power supply and these occurrences has been verified by the results of experiments and application results. To overcome these problems, the proposed method constructs independently a fault-detection, a bypass-control device and a triple power supply apart from the conventional UPS operation. Also the detection point is changed to the preceding of a circuit breaker, a reference of fault detection is modified to avoid any clash and the breaking equipment is attached to intercept a spread of accident. As a result of applications of these developed systems to 242 UPS which was installed purposefully to the communication power supply, the service errors has not occurred in the UPS for two years since 2006.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.5
• /
• pp.703-717
• /
• 2002

This paper illustrates the implementation of a scalable shared buffer asynchronous transfer mode (ATM) switch. The designed shared buffer ATM switch has a shared buffet of a pipelined memory which has the access time of 4 ns. The high-speed buffer access time supports a possibility of the implementation of a shared buffer ATM switch which has a large switching capacity. The designed switch architecture provides flexible switching performance and port size scalability with the independence of queue address control from buffer memory control. The switch size and the buffer size of the designed ATM switch can be reconfigured without serious circuit redesign. The designed prototype chip has a shared buffer of 128-cell and 4 ${\times}$ 4 switch size. It is integrated in 0.6um, double-metal, and single-poly CMOS technology. It has 80MHz operating frequency and supports 640Mbps per port.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1000-1006
• /
• 2007

This paper presents a power detector circuit which monitors the transmitting power for the application in CDMA cell phones. The proposed power detector are composed of coupler for coupling output power and detector fur monitoring output power. The designed coupler has low loss characteristic because it adopts the stripline structure which consists of two ground planes at both sides of signal plane. The design frequency is 824-849MHz which is the Tx band fur CDMA mobile terminal, and the coupling factor of the stripline coupler is -20dB. A schottky barrier diode is adopted for detector design because of its high speed operation with minimized loss. The required impedance matching is performed to improve the linearity and sensitivity of output voltage at relatively low detector input level where the nonlinear characteristic of diode exists. The package parasitics as well as intrinsic diode model are considered for simulation of the detector. The predicted performances agree well with the measured results.