• Journal of Magnetics
• /
• 제20권2호
• /
• pp.186-192
• /
• 2015

This paper describes the electromagnetic and mechanical characteristics of coaxial magnetic gear (CMG) with a low gear ratio. The analysis models are restricted to a CMG with a gear ratio of less than 2. The electromagnetic characteristics including transmitted torque and iron losses are presented according to the variation of the gear ratio. The pole pairs of high speed rotor are chosen as 6, 8 and 10 by considering the torque capability. As the gear ratio approaches 1, both iron losses on the ferromagnetic materials and eddy current losses on the rotor permanent magnets are increased. The radial and tangential forces on the modulating pieces are calculated using the Maxwell stress tensor. When the maximum force is exerted on the modulating pieces, the mechanical characteristics including stress and deformation are derived by structural analysis. In CMG models with a low gear ratio, the maximum radial force acting on modulating pieces is larger than that in CMG models with a high gear ratio, and the normal stress and normal deformation are increased in a CMG with a low gear ratio. Therefore, modulating pieces should be designed to withstand larger radial forces in CMG with a low gear ratio compared to CMG with a high gear ratio.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.1-4
• /
• 2000

We have developed a high performance vertical alignment TFT-LCD, that shows a high light transmittance, and wide viewing angle characteristics with an unusually high contrast ratio. In order to optimize the electro-optical properties we have studied the effect of cell parameters, multi-domain structure and retardation film compensation. With the optimized cell parameters and process conditions, we have achieved a 24" wide UXGA TFT-LCD monitor (16:10 aspect ratio 1920X1200) showing a contrast ratio over 500:1, panel transmittance near 4.5%, response time near 27 ms, and viewing angle higher than 80 degree in all directions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.929-932
• /
• 2006

The effects of polymer-binder ratio, antifoamer content and shrinkage-reducing agent content on the setting time and drying shrinkage of high-fluidity polymer-modified pastes are examined. As a result, the setting time of the high-fluidity polymer-modified pastes tends to delayed with increasing polymer-binder ratio. Irrespective of the antifoamer content, the drying shrinkage of the high-fluidity polymer-modified pastes tend to decrease with increasing polymer-cement ratio and shrinkage-reducing agent content.

• 대한가정학회지
• /
• 제12권2호
• /
• pp.621-631
• /
• 1974

The objective of the study was to obtain standard sizes of body of the high school girls for designing clothes and developing pattern grading of clothes. In 1972, 342 students, selected by the stratified cluster random sampling method, at three high schools in Seoul were measured on forty-one items by the R. Martin method. Statistical techniques of mean, standard deviation, coefficient variable, maximum and minimum, range, t-test were utilized to analyze the data. The findings of the study were as follows ; 1. No differences were found among the age groups in the all measured variables. 2. Stature, bust girth, hip girth, acromion width, posterior waist girth/stature ratio of the high school girls were significantly smaller than those sizes of adult women. This result implies that those sizes will be increased as the students grow up. But upper arm girth, upper arm girth/bust girth ratio, and thigh girth/bust girth ratio were bigger than those sizes of adult women. Waist girth, thigh girth, total head height/stature ratio, acromion width/stature ratio, and foot length/stature ratio were nearly similiar to those of adult women. 3. According to the result of t-test, waist breadth, spinailiaca anterior height/stature ratio, thigh girth/bust girth ratio, and thigh/hip girth ratio of the 15 year old group were significantly different from those of the 16 year old group at the level of 0.05. Bust girth, weight, foot breadth, posterior croth length, and cervical height/stature ratio of the 16 year old group were significantly different from those of the 17 year old group at the level of 0.01. Hip girth, upper arm girth, waist breadth/stature ratio, and neck base girth/bust girth ratio of the 16 year old group were significantly different from those of the 17 year old group at the level of 0.05.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1698-1703
• /
• 2004

To understand the high expansion effects by adopting intake closing time in the cases of compensating intake air-mass and effective compression ratio simultaneously, fundamental study was carried out by using RICEM realizing Atkinson cycle. Intake air-mass and effective compression ratio were compensated by increasing supercharged pressure and geometric compression ratio. The results showed that the increasing rates of expansion ratio and expansion-compression ratio were increased by compensating both a intake air-mass and effective compression ratio the same tendencies were obtained with the increases of compression ratio and cut off ratio It was also found that LIVC has more advantages in expansion ratio and effective work than those of EIVC under above conditions.

• 한국강구조학회 논문집
• /
• 제17권4호통권77호
• /
• pp.395-405
• /
• 2005

본 논문은 고항복비-고강도강의 효율적인 이용을 위하여 유강혼합구조 시스템의 실험결과를 요약한 것이다. 최근 건축구조물에서도 대형화 및 초고층화 되어감에 따라 사용강재에 대하여 높은 성능을 요구하게 되었고, 고강도강을 사용해야 하는 경우가 늘고 있다. 하지만 고강도강은 항복비가 높고 최대 응력시 변형도가 작고 탄성계수가 연강과 같다는 단점으로 인하여 수요가 증가하고 있지 못한 실정이다. 이러한 고항복비를 가지는 고강도강의 결점을 보완하고 효과적인 사용을 위해서는 새로운 구조시스템이 필요하다. 본 연구에서는 고항복비를 가지는 고강도강을 건축구조물에 효과적으로 적용할 수 있는 방안으로 유강혼합구조 시스템을 제안하고, 고강도강이 포함된 유강혼합기둥 실험을 통하여, 고강도강을 효율적으로 사용할 수 있는 가능성을 제시하고자 하였다. 내력비와 강성비를 포함할 수 있는 강요소 (stiff element)와 유요소 (flexible element)의 항복변형비를 변수로 하여, 유강혼합구조시스템 적용시 적절한 항복변형비를 찾고자 하였다. 실험결과 제안된 유강혼합구조시스템은 연강만으로 이루어진 시스템에 비해 높은 에너지 흡수능력을 보여주었고, 강요소에 대한 유요소의 항복변형비가 2.7~3.3일 때 가장 큰 에너지 흡수능력을 갖는 것을 확인할 수 있었다.

• 한국안전학회지
• /
• 제12권2호
• /
• pp.17-21
• /
• 1997

The fatigue crack propagation rate has so far been measured by the effective stress intensity factor range Δ K/sub eff/. But no research has been done to study how much the crack opening ratio influences the expectation of the fatigue crack propagation. Therefore, this paper evaluates of the crack opening ratio on the fatigue crack propagation life by using the method of parameter sensitivity study. Summarizing the result ; ( 1 ) When the crack opening ratio U' is high, the effect of U' gets larger than any other except for the material factor m. But when U' is low, the effect is also diminished. Therefore, the selection of the lowest value possible is desirable in the evaluation of life. (2) When the value of the material factor m is high, the effect of crack opening ratio U' is increased, at the same time the effect of the other parameters also increased wholly. The effect of material factor m itself on life is high, but in case the material factor m is high, that the effect of each parameter on life get higher is unique. In designing, better attention to the material selection should be drawn. (3) In case the stress ratio R gets smaller, the effect of crack opening ratio U' is unchangeable. But the effect of R itself remarkably decreases, and the effect of material factor m somewhat decreases.

• 대한전자공학회논문지SD
• /
• 제47권10호
• /
• pp.34-41
• /
• 2010

본 연구를 통해서 대 면적, 저 전력 AMOLED 용용에 적합한 고 개구율 픽셀 보상회로와 이에 대한 구동회로를 제안하였다. 균일도는 다소 떨어지지만 안정성과 이동도가 뛰어난 저온 다결정 실리콘(LTPS) 박막 트랜지스터(TFT)를 기반으로 설계했다. 픽셀의 불량률을 낮추고 배면발광방식에 적합하도록 픽셀 보상회로를 보다 간단하게 개선하여 고 개구율 특성을 갖도록 했다. 제안하는 고 개구율 픽셀 보상회로는 일반적인 구동방식을 사용할 경우 명암비에서 큰 손해를 볼 수가 있으므로, 명암비를 높게 유지하기 위한 구동방식 및 구동회로를 제안하여 검증하였다. 이와 더불어 동영상 특성을 개선하기 위해 black data insertion 방식을 구현할 수 있도록 설계했다. 배면발광방식의 19.6" WXGA AMOLED 패널에 대해 설계했으며, 픽셀의 평균 개구율은 41.9%로 기존에 비해 8.9% 증가했다. TFT의 $V_{TH}$ 편차가 ${\pm}0.2\;V$일 때, 패널의 불균일도와 명암비는 각각 6% 이하와 10만:1 이상으로 예측되었다.

• 반도체디스플레이기술학회지
• /
• 제20권1호
• /
• pp.70-76
• /
• 2021

A cylindrical microlens (CML) has been widely used as an optical element for organic light-emitting diodes (OLEDs), light diffusers, image sensors, 3D imaging, etc. To fabricate high-performance optoelectronic devices, the CML with high aspect ratio is demanded. In this work, we report on facile solution-based processes (i.e., slot-die and needle coatings) to fabricate the CML using poly(methyl methacrylate) (PMMA). It is found that compared with needle coating, slot-die coating provides the CML with lower aspect ratio due to the wide spread of solution along the hydrophilic head lip. Although needle coating provides the CML with high aspect ratio, it requires a high precision needle array module. To demonstrate that the aspect ratio of CML can be enhanced using slot-die coating, we have varied the molecular weight of PMMA. We can achieve the CML with higher aspect ratio using PMMA with lower molecular weight at a fixed viscosity because of the higher concentration of PMMA solute in the solution. We have also shown that the aspect ratio of CML can be further boosted by coating it repeatedly. With this scheme, we have fabricated the CML with the width of 252 ㎛ and the thickness of 5.95 ㎛ (aspect ratio=0.024). To visualize its light diffusion property, we have irradiated a laser beam to the CML and observed that the laser beam spreads widely in the vertical direction of the CML.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.711-714
• /
• 2004

A new design for improving the aperture ratio of bottom emission type AMOLED is investigated. In conventional, the TFT of AMOLED fabrication method is "Etch Stopper (7-mask)", so the aperture ratio is limited in 28${\sim}$33% by Cs(Storage Capacitor). A high aperture ratio TFT is designed by using BCE(Back Channel Etching 5-mask) fabrication way and the aperture ratio is up to 40% shown in 2.2"AMOLED display.