• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.349-352
• /
• 2014

Anodic alumina oxide (AAO), a self-ordered hexagonal array, has various applications in nanofabrication such as the fabrication of nanotemplates and other nanostructures. In order to obtain highly ordered porous alumina membranes, a two-step anodization or prepatterning of aluminum are mainly conducted with straight electric field. Electric field is the main driving force for pore growth during anodization. However, impurities in aluminum can disturb the direction of the electric field. To confirm this, we anodized two different aluminum foil samples with high purity (99.999%) and relatively low purity (99.8%), and compared the differences in the surface morphologies of the respective aluminum oxide membranes produced in different electric fields. Branched pores observed in porous alumina surface which was anodized in low-purity aluminum and the size; dimensions of the pores were found to be usually smaller than those obtained from high-purity aluminum. Moreover, anodization at high voltage proceeds to a significant level of conversion because of the high speed of the directional electric field. Consequently, anodic alumina membrane of a specific morphology, i.e., meshed pore, was produced.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.528-533
• /
• 2009

High purity $\beta$-SiC powders were synthesized using sol-gel processing. TEOS and phenol resin were used as the starting material for the silicon source and carbon source, respectively. The process turned out to be capable of producing high purity SiC powder purity degree with 99.98 %. However, it was difficult to control the shape and size of $\beta$-SiC powders synthesized by sol-gel process. In this study, $\beta$-SiC powder with size of $1{\sim}5$ um an 30 nm were used as the seeds for $\beta$-SiC to control the $\beta$-SiC powder morphology. It was found that $\beta$-SiC powder seeds was effective to increase the powder average size of synthesized $\beta$-SiC using sol-gel process by acting as the preferred growing sites for $\beta$-SiC.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.1
• /
• pp.22-26
• /
• 2012

An influence of the addition of copper (0.5, 1.0 and 1.5 mass% Cu) on the microstructure and mechanical properties of high purity iron (99.998 mass%) was characterized. The microstructure and microhardness of high-purity iron based samples, which were rolled at room temperature and subsequently annealed, were investigated in this work. The microstructure of the samples has been observed by electron back scattering diffraction (EBSD) and the mechanical properties have been studied by using micro-Vickers hardness test. The results of microstructural observation showed that deformation band was formed in high purity iron by rolling at room temperature, and it was recovered by annealing up to about 900 K. The microhardness results showed that the softening of high-purity iron occurred by annealing up to about 900 K, while the hardness of iron added with about 0.5-1.5 mass% copper was kept over 100 Hv and at the early time of annealing reached a maximum. The hardness of iron added with a small amount of copper may be attributed to precipitation hardening as well as solution hardening. The orientation of crystal in recrystallized grain was almost same as that of deformed grain.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.13-20
• /
• 2014

In this paper, the effects of a nonionic surfactant on the etch uniformity and the etch profile during the wet-etching process of high-purity aluminum were investigated for the fabrication of uniform micropattern arrays. To improve the surface roughness of a high-purity aluminum plate, a mechanical lapping process and an electrolytic polishing process were used. After electrolytic polishing process, the surface roughness, Ra, of the high-purity aluminum plate was improved from $1.25{\mu}m$ to $0.02{\mu}m$. A photoresist was used as an etching mask during the aluminum etching process, where the mixture of phosphoric acid, acetic acid, nitric acid, a nonionic surfactant and water was used as the aluminum etchant. Different amounts of the Triton X-100 nonionic surfactant were added to the aluminum etchant to investigate the effect of a nonionic surfactant during the wet-etching process of high-purity aluminum. The etch rate and the etch profile were measured by an optical interferometer and a scanning electron microscope.

• Journal of Ceramic Processing Research
• /
• v.20 no.4
• /
• pp.388-394
• /
• 2019

In this study, high-purity single-walled carbon nanotubes (SWCNTs) were prepared by removing the unreacted metal constituents and amorphous carbon impurities using a post-annealing process. Unlike conventional thermal processing techniques, this technique involved different gas atmospheres for efficient removal of impurities. A heat treatment was conducted in the presence of chlorine, oxygen, and chlorine + oxygen gases. The nanotubes demonstrated the best characteristics, when the heat treatment was conducted in the presence of a mixture of chlorine and oxygen gases. The scanning electron microscopy, transmission electron microscopy, ultraviolet absorbance, and sheet resistance measurements showed that the heat treatment process efficiently removed the unreacted metal and amorphous carbon impurities from the as-synthesized SWCNTs. The high-purity SWCNTs exhibited improved electrical conductivities. Such high-purity SWCNTs can be used in various carbon composites for improving the sensitivity of gas sensors.

• Archives of Metallurgy and Materials
• /
• v.66 no.4
• /
• pp.935-939
• /
• 2021

In this study, high-purity tantalum metal powder was manufactured via self-propagating high-temperature synthesis. During the process, Ta₂O₅ and Mg were used as the raw material powder and the reducing agent, respectively, and given that combustion rate and reaction temperature are important factors that influence the success of this process, these factors were controlled by adding an excessive mass of the reducing agent (Mg) i.e., above the chemical equivalent, rather than by using a separate diluent. It was confirmed that Ta metal powder manufactured after the process was ultimately manufactured 99.98% high purity Ta metal powder with 0.5 ㎛ particle size. Thus, it was observed that adding the reducing reagent in excess favored the manufacture of high-purity Ta powder that can be applied in capacitors.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.4
• /
• pp.281-286
• /
• 2011

The objective of this study is to optimize the four-bed six-step pressure swing adsorption(PSA) process for high purity $CH_4$ recovery from the biogas. The effects of P/F(purge to feed) ratio and cycle time on the process performance were evaluated. The cyclic steady-states of PSA process were reached after 12 cycles. The purity and recovery rate of product gas, pressure and temperature changes were constant as the cycle repeated. It was shown that the P/F ratio gave significant effect on the product recovery rate by increasing the amount of purge gas in purge and regeneration step. The optimal P/F ratio was found to be 0.08. As the cycle time increased, the product purity decreased by increasing the feed gas flow rate. It was found that the optimal operating conditions were P/F ratio of 0.08 and total cycle time of 1,440 seconds with the purity of 97%.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.11
• /
• pp.1564-1570
• /
• 2016

The present study investigated the immunomodulatory effects of high-purity ${\beta}$-1.3/1.6-glucan on macrophages, natural killer (NK) cells, and T cell-mediated factors. Effect of high-purity ${\beta}$-1.3/1.6-glucan on cytotoxicity in macrophages was investigated. Using macrophages, cytotoxicity of high-purity ${\beta}$-1.3/1.6-glucan was evaluated by MTT assay. We treated high-purity ${\beta}$-1.3/1.6-glucan at concentrations of 10, 50, 100, 150, 200, and $250{\mu}g/mL$ in macrophages. High-purity ${\beta}$-1.3/1.6-glucan did not affect macrophage viability. Phagocytic activity was assessed using zymosan. Activity of high-purity ${\beta}$-1.3/1.6-glucan on macrophages significantly increased as compared with zymosan. We treated high-purity ${\beta}$-1.3/1.6-glucan to murine NK cells co-incubated with YAC-1 cells. High-purity ${\beta}$-1.3/1.6-glucan resulted in significantly increased activity of NK cells as compared with the control. In addition, treatment of macrophages with high-purity ${\beta}$-1.3/1.6-glucan resulted in significantly increased activity of T cell-mediated cytokine (IL-2, IL-12, $IFN-{\gamma}$, and $TNF-{\alpha}$) levels and CD4+/CD8+ T cells as compared with the control. In conclusion, high-purity ${\beta}$-1.3/1.6-glucan could enhance the immune response through activation of macrophages, NK cells, and T cell-mediated factors.

• Nuclear Engineering and Technology
• /
• v.43 no.6
• /
• pp.557-566
• /
• 2011

A cold spray coating (CSC) of copper was studied for its application to a high-level radioactive waste (HLW) disposal canister. Several copper coatings of 10 mm thick were fabricated using two kinds of copper powders with different oxygen contents, and SS 304 and nodular cast iron were used as their base metal substrates. The fabricated CSC coppers showed a high tensile strength but were brittle in comparison with conventional non-coating copper, hereinafter defined to as "commercial copper". The corrosion behavior of CSC coppers was evaluated by comparison with commercial coppers, such as extruded and forged coppers. The polarization test results showed that the corrosion potential of the CSC coppers was closely related to its purity; low-purity (i.e., high oxygen content) copper exhibited a lower corrosion potential, and high-purity copper exhibited a relatively high corrosion potential. The corrosion rate converted from the measured corrosion current was not, however, dependent on its purity: CSC copper showed a little higher rate than that of commercial copper. Immersion tests in aqueous HCl solution showed that CSC coppers were more susceptible to corrosion, i.e., they had a higher corrosion rate. However, the difference was not significant between commercial copper and high-purity CSC copper. The decrease of corrosion was observed in a humid air test presumably due to the formation of a protective passive film. In conclusion, the results of this study indicate that CSC application of copper could be a useful option for fabricating a copper HLW disposal canister.

• Electrical & Electronic Materials
• /
• v.11 no.11
• /
• pp.46-52
• /
• 1998

Barium titanate owes its great importance to the fact that its dielectric constant is about 100 times higher than that of conventional dielectric materials provided its compositional and structural purity is extremely high. The value of crystalline BaTiO3 bodies as used, for instance, in computer elements, magnetic amplifiers, memory device, ets., depend on boththe compositional and the structural purity of the BaTiO3 crystals. This purity will, in turn, depend on the purity of the raw materials used in manufacturing the BaTiO3 compound and on the particularmethods of manufacture which determine the size, homogeneity, and the structural purity of the crystals. This paper reviews the important theoretical considerations, processing techniques and applications related to sol-gel derived thin films.