• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.133-142
• /
• 2014

Recently, more focus is shift to imbalances in aggregate market supply and demand and an exhaustion of natural resources. In this situation, Electric arc furnace oxidizing slag (EAF Slag) has high application possibility as aggregate for concrete due to similar property with general aggregate. In this study, We've got the plan to assure the chemical stability of EAF Slag, and then experimentally tested the mechanical performance and durability for the fine aggregate used EAF Slag. On this test result, we suggest the application plan. At the result of this study, it shows that EAF slag would reduce the surface defect such as pop-out due to natural aging for the fixed hour and adjustment the grain size of EAF Slag. And mechanical performance and durability according to the replacement rate of concrete service, were revealed more than equal or equal compare to general aggregate. Hereafter, quality control must precede not to impede the beauty of concrete surface as assure the safety for aging and processing. And, to establish the environmental resource recycling system for by-products of steel, it should be made development of various application and guideline of quality control for the EAF slag aggregate. Moreover, it must be constantly studied all kind of engineering performance and durability for related to this study.

• Korean Journal of Agricultural Science
• /
• v.47 no.3
• /
• pp.403-414
• /
• 2020

Gradient concentrations of Tithonia diversifolia green leaves and phosphate rocks were used to investigate their contributions as a fertilizer to the yield and quality improvement of a rainfed rice cultivar. Six treatments were compared: (1) T0, no fertilization (control); (2) T1, 1.28 g of phosphate rocks; (3) T2, 250 g of organic matter; (4) T3, 500 g of organic matter; (5) T4, 250 g of organic matter + 1.28 g of phosphate rocks; (6) T5, 500 g of organic matter + 1.28 g of phosphate rocks. The results showed that the germination percentage recorded 15 days after sowing varied from 58 - 76% between T0 and T5. The number of panicles ranged between 2 (T0) to 6.3 (T5). Moreover, the recorded length of the panicles ranged between 7.5 (T1) to 15.8 cm (T2), and the number of grains per panicle ranged between 25.5 (T1) to 273.5 (T3). The plant height was significantly increased in the T5 (79.27 cm) group compared to the T1 (33.63 cm) and control treatment (T0) (40.08 cm) groups. Although the plant height in the T2, T3, and T4 groups was slightly lower than the T5 group, the difference was not statistically significant. The average of the grain number per plant was high in the T3 (273.6 grains) group compared to the T1 and T0 (25.5 and 32.8 grains) groups, respectively. These results suggest that the combination of T. diversifolia leaves and phosphate rocks as a natural fertilizer would be beneficial when integrated into soil fertility management strategies and would contribute to improving crop yield and quality.

• Korean Journal of Food Science and Technology
• /
• v.53 no.3
• /
• pp.245-251
• /
• 2021

We determined the quality characteristics, acrylamide concentration, and antioxidant activity of Nurungji prepared using white rice, brown rice, gamma-aminobutyric acid (GABA) brown rice, oats, and barley. The moisture content of Nurungji prepared using white rice was the lowest (1.48%) and the highest (6.53%) was obtained in barley Nurungji. The brightness (L^*) of white rice Nurungji was the highest, whereas that of GABA brown rice Nurungji was the lowest. The acrylamide concentration was the lowest (37.24 ㎍/g) in white rice Nurungji and the highest (255.50 ㎍/g) in oats Nurungji. The levels of total polyphenol and total flavonoid were the lowest in white rice Nurungji and high in oats and GABA brown rice Nurungji. The antioxidant activity was higher in Nurungji prepared using oats, GABA brown rice, brown rice, and barley than that using white rice. It is necessary to select an appropriate grain when preparing Nurungji by considering the amount of acrylamide produced.

• Korean Journal of Breeding Science
• /
• v.41 no.4
• /
• pp.630-634
• /
• 2009

"Hyedang", a new covered cultivar derived from the crosses between "Suwon300" and "Haganemugi//CI08397/Haganemugi" developed at the Honam Agricultural Research Institute (HARI), NICS, RDA in 2007. The origin of "Hyedang" is "Iksan 407" (SB951033-B-B-B-72). The initial cross was made in 1995 and the selected line showed a high yield and good quality characteristics under yield trial test in 2004. "Iksan407" consistently performed well for three years (2005-2007) from the four locations of regional yield trial (RYT) in Korea and released as "Hyedang". The characteristics of "Hyedang" were the following: rate III growth habit, green leaf and stem, compact spike and with long rough awns. The heading date was April 25 in upland and April 17 in paddy field, which was 2 and 3 days earlier than that of check cultivar, "Olbori". The culm length was 80 cm which was 8 cm shorter than those of check cultivar. It showed spike length of 4.3 cm and 696 spikes per $m^2$, 51 grains per spike, 35.0 g of 1,000 grain weight and 704 g of test weight. It showed stronger winter hardiness and higher resistance to barley yellow mosaic virus (BaYMV) than those with check cultivar. It showed similar protein content and higher whiteness than those of the check cultivar and diastatic power was higher than that of Olbori. The average yield of the pearled grain in the RYT was $4.17ton\;ha^{-1}$ in upland and $4.27ton\;ha^{-1}$ in paddy field, which was 23% and 9% higher than that of the check cultivar, respectively. This cultivar would be suitable for the area above the daily minimum mean temperature of $-8^{\circ}C$ in January in Korean peninsula.

• Korean Journal of Breeding Science
• /
• v.41 no.3
• /
• pp.333-337
• /
• 2009

A new malting barley variety, "Daho", was developed from the cross between "Milyang85 and Suwon335" at the Department of Rice and Winter Cereal Crop (DRWCC) NICS, in 2007. An elite line, YMB2064-B-8-2-4-1-1, was selected in 2004 and designated as "Milyang134". It showed good agronomic performance in the regional adaptation yield trials (RYT) from 2005 to 2007 and was released with the name of "Daho", having high yielding and BaYMV resistance. The average heading and maturing dates of "Daho" were April 19 and May 27, which were 2 days later and 1 day earlier than those of "Jinyang", leading variety, at the regional adaptation yield trials (RYT), respectively. "Daho" had longer culm length (84 cm), more spikes per $m^2$ (915) and higher 1,000 grain weight (39.2 g) than those of "Jinyang" in paddy field condition. "Daho" was showed resistance to BaYMV at the regions of Naju, Jinju, and Milyang but moderately resistance at Iksan. However, the response of "Daho" to other environmental stresses was similar to "Jinyang". The yields of "Daho" at upland and paddy fields were about 5.20 MT/ha, 4.81 MT/ha, respectively, which is about 38%, 25% higher than those of "Jinyang" in the regional adaptation yield trials (RYT), respectively. It has higher grain assortment, germination capacity, water sensitivity and Kolback index but lower malt extract, diastatic power and filtration speed than those of "Jinyang".

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.65-83
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well. 2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air. 3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying. 4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis. 5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time. 6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture. 7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation. 8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise. 11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss. 12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method. 13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated. Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year. 14. Required fan horsepower and energy for the intermittent fan operation were 3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation. 15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use. 16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Korean Journal of Breeding Science
• /
• v.42 no.3
• /
• pp.313-317
• /
• 2010

There are the farmer's needs to develop early-maturing cultivar adaptable to mid-northern inland plain and alpine area. Furthermore, it is required to develop a rice variety to produce new rice before concentrated marketing dates, even in the years of early Chuseok. 'Joun' is a new extremely early-maturing japonica rice cultivar developed in 2009 from the cross of SR14880-173-3-3-2-2-2/Unbong20 at Cheolwon Substation, National Institute of Crop Science (NICS), Rural Development Administration (RDA). The heading date of 'Joun' is July 23 in mid-northern alpine area, which is 7 days earlier than that of Odaebyeo. It has about 61 cm in culm length with semi-erect plant type. Panicle has a few awns and its exertion is good. The number of spikelets per panicle is smaller than that of Odaebyeo and 1,000 grain-weight of brown rice is 21.2 g which is less than 26.3 g of Odaebyeo, but the complete grain ratio is higher. Milled kernels are translucent with non-glutinous endosperm and palatability of cooked rice is good. It shows strong resistance to cold treatment, lodging, premature heading, wilting and viviparous germination during ripening stage. This cultivar shows resistance to leaf blast disease but susceptible to bacterial blight, virus disease and insect pests. The milled rice yield performance of 'Joun' is about 5.18 MT/ha by ordinary culture in local adaptability test for three years. This cultivar may be highly adaptable to the mid-northern inland plain and alpine area, north-eastern coastal area and middle plain area.

• Korean Journal of Breeding Science
• /
• v.40 no.4
• /
• pp.533-536
• /
• 2008

Hopum is a new japonica rice cultivar developed from the cross between Milyang165 and F1 crossing Milyang165 and Iksan438 at Department of Rice and Winter Cereal Crop, NICS, RDA, in 2006. This cultivar has a short grain shape and about 141 days growth duration from direct seeding to harvesting in the southern plain including Chungcheong province. This cultivar has short culm and spikelet number per panicle is similar to that of Nampyeongbyeo, while filled grain rate is lower than standard variety. This cultivar has medium size of brown rice and shows moderate resistance to leaf blast, to bacterial blight pathogens of $K_1$, $K_2$ and $K_3$ and stripe virus disease but susceptible to major virus diseases and insect pests. The milled kernel of Hopum is translucent with non-glutinous endosperm. Protein and amylose content of Hopum is about 6.5% and 18.7%, respectively. This cultivar has better palatability of cooked rice than Chucheongbyeo harvested in Gyeongki province. Its milling recovery (76.8%) and percentage of perfect-shaped milled rice (94.7%) were higher than Nampyeongbyeo. The milled rice yield of Hopum was 5.83 MT/ha (15% higher than Juan) under wet-direct seeding, 5.66 MT/ha (8% higher than Juan) under dry-direct seeding, and 6.00 MT/ha (8% higher than Nampyeong) under ordinary transplanting cultivation. "Hopum" would be adaptable for ordinary transplanting and direct seeding in the southern plain including Chungcheong province.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.spc1
• /
• pp.35-41
• /
• 2006

This study was conducted to establish the post-harvest management system in rice. Harvested hulled rice was gathered into large-scale bag and combine bag, in which the rice quality and the influence on quality change were investigated on various storage periods and moisture contents. Moisture content of hulled rice ranged from 23.7% to 28.8% on different harvest times, which grew lower as harvesting time was delayed. When desiccation was retarded hulled rice in large scale bag was changed in color and emitted an of offensive odor in 3 days and that in combine bag showed similar symptom in 4 days. Inner temperature in large scale bag was changed a lot when the storage period was prolonged and also the moisture content was higher while that in combine bag increased regularly corresponding to the moisture content at the time of harvest. Moisture content of hulled rice stored in large-scale bag increased 2 days after harvest and the more moisture content showed the more increased tendency, while in the case of combine bag the moisture content was not changed much whether the hulled rice contained low or high moisture content in harvesting. As desiccation was delayed fatty acid increased much more in large-scale bag than in combine bag even though protein and amylose contentwere not changed. As desiccation was delayed more and hulled rice contained moisture more in harvesting head rice ratio of brown rice decreased and green-kerneled rice and damaged grain ratio increased and quality of milled rice also became deteriorated. As a result, desiccation day to minimize the deterioration of rice quality was estimated 1-2 days in large scale bag and 2-3 days in combine bag after harvesting.