• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.110-113
• /
• 1999

본 연구에서는 고주파 유도가열을 위한 전원장치에 사용되는 인버터 시스템의 대용량, 고조파화를 실현하기 위한 고주파화 기술을 제안하였다. 부한 공진 인버터는 H형 전-브리지(Full-Bridge)로 구성하고 각 암당 IBGT를 2병렬로 조합하여 구성하고 부하는 직병열 공진회로로 구성한다. 스위칭 동작은 8개의 IGBT중 각 ARM당 2개씩 순차 제어하여 고속 대용량의 고주파 전력을 출력시킨다. 또한 스위칭은 스위치 턴온·오프시에 스위칭 손실을 줄이기 위해 ZVS(Zero-Voltage Switching) 기법을 도입한다. 제어는 고정주파수 PWM(Pulse Width Modulation) 제어를 하여 전력변환 효율을 극대화한다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.314-318
• /
• 1998

This paper discusses the development of electronic ballast for neon lamp as an application of a zero voltage switching high frequency inverter. Abnormal increase of secondary voltage due to grounded fault or partial damage of serial arranged loads is clarified and the protection circuit for this abnormal voltage increase is proposed. Also stable lighting condition for removing the unstable characteristics due to different load conditions is proposed.

• 조명전기설비학회논문지
• /
• 제16권2호
• /
• pp.18-25
• /
• 2002

본 논문은 고압 방전램프를 점등시켜 주는 전자식 안정기에 관한 것으로서, Class D LCC 공진 인버터 방식을 이용하여, 램프의 초기 점등, 정상상태를 구동하게 하고, 준구형파로 ZC-ZVS Soft Switching을 구현하여 풀-브리지 스위치의 발열을 최소화할 수 있도록 하였다. 또한, RCD 스너버 회로를 적용하여 스위치 발열 감소뿐만 아니라, 고주파 스위칭으로 인한 서지 전압의 감소를 통한 노이즈를 최소화시켜 제어부의 안정되고, 신뢰성 있는 동작을 가능하게 할 수 있도록 하고, 안정기의 전체적인 스위칭 노이즈 발생을 최소화하였다.

• 전기학회논문지
• /
• 제57권10호
• /
• pp.1782-1789
• /
• 2008

This paper presents the design of acoustic resonance(AR) free and dimmable electronic ballast for 1kW Metal-Halide Lamp(MHL). The proposed Ballast consists of a Full-Bridge(FB) rectifier, a passive power factor correction(PFC) circuit, a full-bridge inverter, an ignitor using LC resonance and a control circuit for frequency modulation and dimming control. Whereas a passive PFC provides advantages in terms of high reliability and low cost for constructing the circuit, it is difficult to supply a stable voltage because of the output voltage ripple that occurs with a period of 120Hz. Although the ballast can be designed with a small size and a light weight if it is driven at a switching frequency between 1 and 100 kHz, AR will occur if the eigenvalue frequency of the lamp coincides with the inverter's operation frequency. The operation frequency was modulated in real time according to the output voltage ripple to compensate for the variation in power supplied to the lamp and eliminate AR. For dimming, the method, which modulated drive frequency of FB inverter using the control of DC level by microprocessor, was used. The Dimming ranged at least from 600W to 1kw as rated power of the lamp with 4 stages. Performance of the proposed technique was validated through numerical analysis, computer simulation using Pspice and by applying it to an electronic ballast for a prototype 1kW MHL.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.374-378
• /
• 2016

The transformer used in an inverter type arc welding machine is designed to use high frequency in order to reduce its size and cost. Also, selecting core materials that fit frequency is important because core loss increases in a high frequency band. An inrush current can occur in the primary coil of transformer during arc welding and this inrush current can cause IGBT, the switching element, to burn out. The transformer design was carried out in $A_P$ method and amorphous core was used to reduce the size of transformer. In addition, sheet coil was used for primary winding and secondary winding coil considering the skin effect. This paper designed the transformer core with an air gap to prevent IGBT burnout due to the inrush current during welding and proposed the optimum air gap length.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1126-1128
• /
• 2001

A single-stage high-power-factor electron ic ballast operating in critical conduction mode is presented in this paper. The proposed topology is based on integration of a boost-like converter and a LCC Type half-bridge serial resonant inverter. The power-factor-correction(PFC) stage is a boost-like converter operating in critical conduction mode for positive and negative half cycle voltage respectively at line frequency (60Hz) so that a high power factor is achieved naturally. The simulated and experimental results for 100w fluorescent lamps operating at 42kHz switching frequency and 220V line voltage have been obtained.

• Journal of Power Electronics
• /
• 제13권2호
• /
• pp.296-303
• /
• 2013

This paper proposes a high efficiency three-phase cascaded phase shifted H-bridge multi-level inverter without DC/DC converters for grid-tied multi string photovoltaic (PV) applications. The cascaded H-bridge topology is suitable for PV applications since each PV module can act as a separate DC source for each cascaded H-bridge module. The proposed phase shifted H-bridge multi-level topology offers advantages such as operation at a lower switching frequency and a lower current ripple when compared to conventional two level topologies. It is also shown that low ripple sinusoidal current waveforms are generated with a unity power factor. The control algorithm permits the independent control of each DC link voltage with a maximum power point for each string of PV modules. The use of the controller area network (CAN) communication protocol for H-bridge multi-level inverters, along with localized PWM generation and PV voltage regulation are implemented. It is also shown that the expansion and modularization capabilities of the H-bridge modules are improved since the individual inverter modules operate more independently. The proposed topology is implemented for a three phase 240kW multi-level PV power conditioning system (PCS) which has 40kW H-bridge modules. The experimental results show that the proposed topology has good performance.

• 조명전기설비학회논문지
• /
• 제22권4호
• /
• pp.166-171
• /
• 2008

본 논문은 가변주파수 스위칭 방식의 flyback 컨버터를 이용한 자동차용 35[W]급 고휘도 방전 램프용 전자식 안정기의 고효율 제어시스템을 구현하였다. 또한 안정기 성능, 크기 그리고 효율을 고려하여 planar 변압기를 이용하여 flyback 컨버터를 설계하였다. HID 램프를 자동차에 적용하기 위해 복잡한 과도특성을 제어할 수 있는 매우 복잡한 제어회로와 고효율의 안정기의 제작이 요구되어진다. 제안된 전자식 안정기는 planar 변압기를 사용한 flyback 컨버터, full bridge 인버터와 승압 점화장치로 구성되어 있으며, flyback 컨버터의 스위칭 주파수는 안정기에 입력전압의 변화에 따라 제어되도록 설계하였고, planar변압기를 사용하여, 안정기의 가격과 크기를 크게 절감할 수 있었다. 제안된 시스템에 대한 성능 및 효율은 여러 가지 실험을 통해 확인하였다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제3B권1호
• /
• pp.44-51
• /
• 2003

The module UPS can flexibly implement expansion of power system capacities. Further-more, it can be used to build up the parallel redundant system to improve the reliability of power system operation. To realize the module UPS, load sharing without interconnection among parallel connecting modules as well as a small scale and lightweight topology is necessary. In this paper, the three-arm converter/inverter is compared with the general full-bridge and half-bridge topology from a practical point of view and chosen as the module UPS topology. The switching control approaches based on a pulse width modulation of the converter and inverter of the system are presented independently. The frequency and voltage droop method is applied to parallel operation control to achieve load sharing. Two prototype 3㎸A modules are designed and implemented to confirm the effectiveness of the pro-posed approaches. Experimental results show that the three-arm UPS system has a high power factor, a low distortion of output voltage and input current, and good load sharing characteristics.

• 한국콘텐츠학회논문지
• /
• 제10권4호
• /
• pp.257-264
• /
• 2010

기존의 경두개 자극장치는 일정한 자극치료 펄스의 정현파 모양으로 다양한 치료 및 진단을 하는데 한계가 있다. 본 연구에서, 치료 및 진단마다 요구되는 세기, 폭, 펄스모양이 다른 코로로프트-월톤회로와 반파브리지 공진 인버터를 도입하여 주파수와 전압이 가변되는 새로운 장치를 제안하고자 한다. 기존장치 보다 많은 장점을 가진다. 첫째로 고압 변압기를 가지지 않는다. 둘째로 스위칭손실이 적고, 출력에너지를 정밀하게 제어할 수가 있다. 세째로 자극의 세기, 폭, 펄스모양이 다양하다. 결과적으로 변압기를 사용하지 않는 반파브리지 인버터와 코크로프트-월톤회로를 적용하여 개선된 특성과 실험을 구하였다.