• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4652-4659
• /
• 2022

Among the detector materials available at room temperature, thallium bromide (TlBr), which has a relatively high atomic number and density, is widely used for gamma camera imaging. This study aimed to verify the usefulness of TlBr through quantitative evaluation by modeling detectors of various compound types using Monte Carlo simulations. The Geant4 application for tomographic emission was used for simulation, and detectors based on cadmium zinc telluride and cadmium telluride materials were selected as a comparison group. A pixel-matched parallel-hole collimator with proven excellent performance was modeled, and phantoms used for quality control in nuclear medicine were used. The signal-to-noise ratio (SNR), contrast to noise ratio (CNR), sensitivity, and full width at half maximum (FWHM) were used for quantitative analysis to evaluate the image quality. The SNR, CNR, sensitivity, and FWHM for the TlBr detector material were approximately 1.05, 1.04, 1.41, and 1.02 times, respectively, higher than those of the other detector materials. The SNR, CNR and sensitivity increased with increasing detector thickness, but the spatial resolution in terms of FWHM decreased. Thus, we demonstrated the feasibility and possibility of using the TlBr detector material in comparison with commercial detector materials.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.25 no.1
• /
• pp.51-70
• /
• 1995

The purpose of this investigation was to compare the direct digital radiographic system with film-based digital imaging system using Ektaspeed and Ektaspeed Plus film with respect to image characteristics and detectability and evaluate the sensor noise with the use of subtraction method. Direct digital radiographic system which used was Sens-A-Ray system(Regam Medical Systems, Sundsvall, Sweden) and film-based digital imaging system was composed of Macintosh II ci computer, high resolution Sony XC-77 CCD camera and intraoral x-ray film(Kodak Ektaspeed film, Kodak Ektaspeed Plus film). Images were taken by using CCD sensor of Sens-A-Ray system, Ektaspeed film and Ektaspeed Plus film with variable exposure time(0.06s, 0.1s, 0.16s, 0.2s, 0.3s, 0.4s, 0.5s, 0.6s, O.8s, LOs), 5 times at each exposure time. And then ektaspeed films and ektaspeed plus films were digitized using CCD camera. Image groups were divided into 3 groups; Sens-A-Ray group(direct digital radiographic system), Ektaspeed group and Ektaspeed Plus group (film-based digital imaging system) They were assessed by the following three aspects; image density, image contrast and detectability and sensor noise of Sens-A-Ray system was also evaluated. The results were as follow : 1. S group showed higher density than E , EP group except at the low exposure time(p<0.01). 2. S group showed higher contrast than E,EP group except at the high exposure time(p<0.01). 3. All groups showed good detectability at the each proper exposure time. Lowest exposure time which shows maximum detectability in S,EP group(0.5s) was lower than that in E group(0.6s). 4. Sensor noise of Sens-A-Ray system generally increased according to exposure time. On the basis of the above results, it was considered that Sens-A-Ray system could show higher speed, higher contrast than Ektaspeed, Ektaspeed Plus film except at too high and low exposure time and the same detectability as the conventional intraoral film.

• Applied Microscopy
• /
• v.40 no.1
• /
• pp.21-28
• /
• 2010

In a simulation study of atomic resolution transmission electron microscope images of single layer and bilayer graphene, it is demonstrated that the conventional Bloch wave formulations can be used when high-order Laue zone reflections are properly taken into account in the theory. The simulated images for bilayer graphene show 3-fold rotational lattice symmetry rather than the 6-fold one under certain conditions. This result can be understood as revealed the 3-fold rotational lattice symmetry of bilayer graphene in three dimensions along [0001]. For single layer graphene the observed phase images showing 3-fold rotational lattice symmetry were particularly noted. This phenomenon has been explained by an assumption of the re-configuration of electron density on the surface of graphene. And the matching images have been obtained as simulated with up to the second order Laue zone reflections only, reflecting the re-configuration of electrons on the surface.

• Journal of Biomedical Engineering Research
• /
• v.30 no.2
• /
• pp.179-184
• /
• 2009

Magnetic Resonance Electrical Impedance Tomography (MREIT) is a new bio-imaging modality providing cross-sectional conductivity images from measurements of internal magnetic flux densities produced by externally injected currents. Recent MREIT studies demonstrated successful conductivity image reconstructions of postmortem and in vivo canine brain. However, the whole head imaging was not achieved due to technical issues related with electrodes and noise in measured magnetic flux density data. In this study, we used a new carbon-hydrogel electrode with a large contact area and injected 30 mA imaging current through a canine head. Using a 3T MREIT system, we performed a postmortem canine experiment and produced high-resolution conductivity images of the entire canine head. Collecting magnetic flux density data inside the head subject to multiple injection currents, we reconstructed cross-sectional conductivity images using the harmonic $B_z$ algorithm. The conductivity images of the canine head show a good contrast not only inside the brain region including white and gray matter but also outside the brain region including the skull, temporalis muscle, mandible, lingualis proprius muscle, and masseter muscle.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.463-469
• /
• 1996

The double insulating layer consisting of anodic oxide and ZnS was formed for HgCdTe metal insulator semiconductor(MIS) structure. ZnS was evaporated on the anodic oxide grown in H$_{2}$O$_{2}$ electrolyte. Recently, this insulating mechanism for HgCdTe MIS has been deeply studied for improving HgCdTe surface passivation. It was found through TEM observation that an interface layer is formed between ZnS and anodic oxide layers for the first time in the study of this area. EDS analysis of chemical compositions using by electron beam of 20.angs. in diameter and XPS depth composition profile indicated strongly that the new interface is composed of ZnO. Also TEM high resolution image showed that the structure of oxide layer has been changed from the amorphous state to the microsrystalline structure of 100.angs. in diameter after the evaporation of ZnS. The double insulating layer with the resistivity of 10$^{10}$ .ohm.cm was estimated to be proper insulating layer of HgCdTe MIS device. The optical reflectance of about 7% in the region of 5.mu.m showed anti-reflection effect of the insulating layer. The measured C-V curve showed the large shoft of flat band voltage due to the high density of fixed oxide charges about 1.2*10$^{12}$ /cm$^{2}$. The oxygen vacancies and possible cationic state of Zn in the anodic oxide layer are estimated to cause this high density of fixed oxide charges.

• Proceedings of the Korean Printing Society Conference
• /
• 2007.11a
• /
• pp.13-28
• /
• 2007

Producing printing plate is essential progress to do offset printing. In this Film-less period, the more PS plate becomes extinct, the more the age of the Plate-Making of Exposure declines the place to stand. To do offset printing, the CTP (Computer to Plate) is taking a place of PS plate that covers speed, quality and economical problems. The biggest advantage of using CTP is that laser directly goes to the plate, thus there are no dust from the Plate-Making of Exposure. It is also theoretically able to print 200lpi${\sim}$300lpi as well as print 1751pi, because it has over 2400dpi resolution. The high quality printing could be available inside of the country, if printing machine keeps the optimum condition in offset printing. The CTP has many advantages, however there is a difficulty for the operators to preserve the equipment. The actual circumstance is that they cannot make a decision about how many dots need to be generated, and also it is necessary to know how to establish the setup at RIP on CTP to make the optimum condition output. If offset printing machine keeps the optimum condition, it would be able to print up to high quality printing however it is hard to comment what is the optimum condition for the printing machine. Anyone could say easy subjectively that machine is in the optimum condition, however it is objectively hard to estimate by number. In this research GATF / Plate Test target used to analyze the image and to make numerical value of the optimum condition of the CTP. It also used GATF / The sheep fed test printing 5.0 to know the density of the color representation, dot gain and gray balance for the optimum condition of the print machine. The purpose of this research is to represent the ISO 12647-2 which is the international standard with domestic printing equipments.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.25 no.2
• /
• pp.69-84
• /
• 2007

Producing printing plate is essential progress to do offset printing. In this Film-less period, the more PS plate becomes extinct, the more the age of the Plate-Making of Exposure declines the place to stand. To do offset printing, the CTP (Computer to Plate) is taking a place of PS plate that covers speed, quality and economical problems. The biggest advantage of using CTP is that laser directly goes to the plate, thus there are no dust from the Plate-Making of Exposure. It is also theoretically able to print $200lpi{\sim}300lpi$ as well as print 1751pi, because it has over 2400dpi resolution. The high quality printing could be available inside of the country, if printing machine keeps the optimum condition in offset printing. The CTP has many advantages, however there is a difficulty for the operators to preserve the equipment. The actual circumstance is that they cannot make a decision about how many dots need to be generated, and also it is necessary to know how to establish the setup at RIP on CTP to make the optimum condition output. If offset printing machine keeps the optimum condition, it would be able to print up to high quality printing however it is hard to comment what is the optimum condition for the printing machine. Anyone could say easy subjectively that machine is in the optimum condition, however it is objectively hard to estimate by number. In this research GATF / Plate Test target used to analyze the image and to make numerical value of the optimum condition of the CTP. It also used GATF / The sheep fed test printing 5.0 to know the density of the color representation, dot gain and gray balance for the optimum condition of the print machine. The purpose of this research is to represent the ISO 12647-2 which is the international standard with domestic printing equipments.

• Journal of Urban Science
• /
• v.7 no.2
• /
• pp.53-60
• /
• 2018

Digital Twin is a technology that creates a photocopy of real-world objects on a computer and analyzes the past and present operational status by fusing the structure, context, and operation of various physical systems with property information, and predicts the future society's countermeasures. In particular, 3D rendering technology (UAS, LiDAR, GNSS, etc.) is a core technology in digital twin. so, the research and application are actively performed in the industry in recent years. However, UAS (Unmanned Aerial System) and LiDAR (Light Detection And Ranging) have to be solved by compensating blind spot which is not reconstructed according to the object shape. In addition, the terrestrial LiDAR can acquire the point cloud of the object more precisely and quickly at a short distance, but a blind spot is generated at the upper part of the object, thereby imposing restrictions on the forward digital twin modeling. The UAS is capable of modeling a specific range of objects with high accuracy by using high resolution images at low altitudes, and has the advantage of generating a high density point group based on SfM (Structure-from-Motion) image analysis technology. However, It is relatively far from the target LiDAR than the terrestrial LiDAR, and it takes time to analyze the image. In particular, it is necessary to reduce the accuracy of the side part and compensate the blind spot. By re-optimizing it after fusion with UAS and Terrestrial LiDAR, the residual error of each modeling method was compensated and the mutual correction result was obtained. The accuracy of fusion-based 3D model is less than 1cm and it is expected to be useful for digital twin construction.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.4
• /
• pp.67-74
• /
• 2016

Drone images with high spatial resolution are emerging as an alternative to previous studies with extraction limits in high density forests. Individual tree in the dense forests were extracted from drone images. To detect the individual tree extracted through the image segmentation process, the image segmentation results were compared between the combination of DSM and all R,G,B band and the combination of DSM and R,G,B band separately. The changes in the tree density of a deciduous forest was experimented by time and image. Especially the image of May when the forests are dense, among the images of March, April, May, the individual tree extraction rate based on the trees surveyed on the site was 50%. The analysis results of the width of crown showed that the RMSE was less than 1.5m, which was the best result. For extraction of the experimental area, the two sizes of medium and small trees were extracted, and the extraction accuracy of the small trees was higher. The forest tree volume and forest biomass could be estimated if the tree height is extracted based on the above data and the DBH(diameter at breast height) is estimated using the relational expression between crown width and DBH.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.1
• /
• pp.1-6
• /
• 2020

In this research, 50 nm thick AlN thin films were deposited on the patterned sapphire (0001) substrate by using HVPE (Hydride Vapor Phase Epitaxy) system and then epitaxial layer structure was grown by MOCVD (metal organic chemical vapor deposition). The surface morphology of the AlN buffer layer film was observed by SEM (scanning electron microscopy) and AFM (atomic force microscope), and then the crystal structure of GaN films of the epitaxial layer structure was investigated by HR-XRC (high resolution X-ray rocking curve). The XRD peak intensity of GaN thin film of epitaxial layer structure deposited on AlN buffer layer film and sapphire substrate was rather higher in case of that on PSS than normal sapphire substrate. In AFM surface image, the epitaxial layer structure formed on AlN buffer layer showed rather low pit density and less defect density. In the optical output power, the epitaxial layer structure formed on AlN buffer layer showed very high intensity compared to that of the epitaxial layer structure without AlN thin film.