• 한국지구과학회지
• /
• 제36권4호
• /
• pp.315-329
• /
• 2015

본 연구에서는 2005~2010년 기간 동안 영동지역의 지형성 강풍과 관련된 태백산맥 풍하측에서 관측된 기상요소들을 분석하였다. 강풍 사례는 강원지역에서 풍속이 $14ms^{-1}$ 이상인 조건을 이용하여 선정하였다. 강풍 사례는 총 15일로 나타났고, 모두 영동지역에 위치한 속초, 강릉, 동해, 그리고 태백 지역에서 발생하였다. 사례 중 태풍(세 사례) 그리고 영동지역의 대설(두 사례)과 호우(두 사례)와 관련된 7개 사례는 이 연구에서 제외하였다. 8개 강풍 사례를 분석하기 위하여 종관 일기도, 속초 고층 관측, 강릉 수직측풍, 그리고 수치모델 자료를 사용하였다. 선정된 사례는 무강수 혹은 일강수량 1mm 이하의 강수를 보였다. 종관 일기도에서 나타난 지상과 상층의 특징은 기압분포가 한반도를 중심으로 남고북저형을 보였고, 영동지역으로 온도능(warm ridge)이 위치하였다. 역전층(혹은 안정층)과 온도능은 하층 강풍대와 함께 산 정상의 약 1~3 km (925~700 hPa) 고도에 위치하였다. 또한 지역예보시스템에서 분석된 온난핵과 온도능은 산 정상 상공의 850 hPa 등압면 고도에 위치하였고, 이 고도에서 수평 온도 경도는 $0.10{\sim}0.23^{\circ}C\;km^{-1}$로 분석되었다. 이러한 분석 결과는 영동지역 강풍 예보 가이던스로 요약되었다.

• 한국재료학회지
• /
• 제19권4호
• /
• pp.179-185
• /
• 2009

We fabricated thermally evaporated 30 nm-Ni/(20 nm or 60 nm)a-Si:H/Si films to investigate the energy-saving property of silicides formed by rapid thermal annealing (RTA) at temperatures of $350^{\circ}C$, $450^{\circ}C$, $550^{\circ}C$, and $600^{\circ}C$ for 40 seconds. A transmission electron microscope (TEM) and a high resolution X-ray diffractometer (HRXRD) were used to determine the cross-sectional microstructure and phase changes. A UVVIS-NIR and FT-IR (Fourier transform infrared spectroscopy) were employed for near-IR and middle-IR absorbance. Through TEM and HRXRD analysis, for the nickel silicide formed at low temperatures below $450^{\circ}C$, we confirmed columnar-shaped structures with thicknesses of $20{\sim}30\;nm$ that had ${\delta}-Ni^2Si$ phases. Regarding the nickel silicide formed at high temperatures above $550^{\circ}C$, we confirmed that the nickel silicide had more than 50 nm-thick columnar-shaped structures with a $Ni_{31}Si_{12}$ phase. Through UV-VIS-NIR analysis, nickel silicide showed almost the same absorbance in the near IR region as well as ITO. However, in the middle IR region, the nickel silicides with low temperature showed similar absorbance to those from high temperature silicidation.

• 열처리공학회지
• /
• 제7권4호
• /
• pp.277-287
• /
• 1994

The effect of grain size on the tensile properties and fatigue behavior of austenitic high Mn steel has been investigated. The recrystallized austenite grain size of the cold rolled high Mn steel was increased as the annealing temperature increased from $600^{\circ}C$ to $1000^{\circ}C$. Larger austenite grain size decreased the yield strength and the tensile strength, and increased the uniform elongation due to transformation of some austenite into twins or E-martensite phase during deformation. Austenite grain refinement increased the tendency to form dislocation cells, instead. The specimen annealed at $1000^{\circ}C$ with large grain size showed lower fatigue crack propagation rate in low ${\Delta}K$ region due to rougher fracture surface caused by formation of deformation twins during fatigue at the crack tip region.

• 열처리공학회지
• /
• 제37권4호
• /
• pp.182-187
• /
• 2024

To improve and control the mechanical properties of low alloy steel, the influence of quenching and tempering process conditions was investigated. In the case of quenching heat treatment, a comparison was made between the conventional method of heating to the austenite region followed by single quenching and a method involving double quenching, followed by high-temperature tempering. It was observed that specimens subjected to double quenching exhibited significantly finer tempered microstructures compared to those subjected to conventional quenching, resulting in noticeably higher hardness. Additionally, a study was conducted to investigate the variation in hardness with changes in tempering temperature and time after the same conventional quenching treatment. As expected, an increase in tempering temperature or time led to a decrease in hardness, and the correlation between hardness and the Hollomon-Jeffe Parameter was confirmed. It was also observed that during high-temperature tempering, the size of carbides significantly increased.

• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.175-180
• /
• 2007

High temperature superconductor $YBa_2Cu_3O_{7-x}$ (YBCO) films have been grown by in-situ electron beam evaporation on artificial metal tapes such as ion-beam assisted deposition (IBAD) and rolling assisted biaxially textured substrates (RABiTS). Deposition rate of the YBCO films is $10{\sim}100{\AA}/sec$. X-ray diffraction shows that the films are grown epitaxially but have inter-diffusion phases, like as $BaZrO_3\;or\;BaCeO_3$, at their interfaces between YBCO and yttrium-stabilized zirconia (YSZ) or $CeO_2$, respectively. Secondary ion mass spectroscopy depth profile of the films confirms diffused region between YBCO and the buffer layers, indicating that the growth temperature ($850{\sim}900^{\circ}C$) is high enough to cause diffusion of Zr and Ba. The films on both the substrates show four-fold symmetry of in-plane alignment but their width in the -scan is around $12{\sim}15^{\circ}$. Transmission electron microscopy shows an interesting interface layer of epitaxial CuO between YBCO and YSZ, of which growth origin may be related to liquid flukes of Ba-Cu-O. Resistivity vs temperature curves of the films on both substrates were measured. Resistivity at room temperature is between 300 and 500 cm, the extrapolated value of resistivity at 0 K is nearly zero, and superconducting transition temperature is $85{\sim}90K$. However, critical current density of the films is very low, ${\sim}10^3A/cm^2$. Cracking of the grains and high-growth-temperature induced reaction between YBCO and buffer layers are possible reasons for this low critical current density.

• 한국초전도ㆍ저온공학회논문지
• /
• 제21권3호
• /
• pp.1-5
• /
• 2019

The superconductor stability theories are consistently described by the integral formula. If the defined stability function is a simple decreasing function, it becomes a cryogenic stability condition. If the stability function has a maximum value and a minimum value, and the maximum value is less than 0, then it is a cold-end recovery condition. If the maximum value is more than 0, it can be shown that the unstable equilibrium temperature, that is, the MPZ (minimum propagation zone) temperature distribution can exist. The MPZ region is divided into two regions according to the current ratio. At the low current ratio, the maximum dimensionless temperature is greater than 1, and at the relatively high current ratio, the maximum dimensionless temperature is less than 1. In order to predict the minimum quench energy, the dimensionless energy was obtained for the MPZ temperature distribution. In particular, it was shown that the dimensionless energy can be obtained even when the MPZ maximum temperature is 1 or more.

• 한국전산유체공학회지
• /
• 제9권3호
• /
• pp.18-25
• /
• 2004

Multi plume effects on the base heating have been Investigated with a CFD program. As the flight altitude increases, the plume expansion angle increases regardless of the single or clustered engine. The plume interaction of the clustered engine makes a high temperature thermal shear in the center of four plumes. At low altitude, the high temperature shear flow stays in the center of plumes, but it increases up to engine base with the increasing altitude. At high altitude, the flow from plume to base and the flow from base into outer free stream are supersonic, which transfers the high heat in the center of plumes to the base region. The radiative heat of the clustered engine varies from 220 kW/m² to 469 kW/m² with increasing altitude while those of the single engine are 10 kW/m² and 43.7 kW/m². And the base temperature of the clustered engine varies from 985K to 1223K, and those of the single engine are 483K and 726K. This big radiative heat of clustered engine can be explained by the active high temperature base flow and strong plume interactions.

• 한국제4기학회지
• /
• 제21권1호
• /
• pp.15-26
• /
• 2007

A wide tree-ring data network from Western Himalayan region as well as from Central and Peninsular India have been established by the Indian Institute of Tropical Meteorology (IITM), Pune, India. This includes several ring width and density chronologies of Himalayan conifers (Pinus, Picea, Cedrus, Abies)covering entire area of Western Himalaya and teak (Tectona grandis L.F.) from central and peninsular India. Many of these chronologies go back to $15^{th}$ century. Tree-ring based reconstructed pre-monsoon (March-April-May) summer climate of Western Himalaya do not show any significant increasing or decreasing trend since past several centuries. High altitude tree-ring chronologies near tree line-glacier boundary are sensitive to the winter temperature. Unprecedented higher growth in recent decades is closely associated with the warming trend over the Himalayan region. Dendroclimatic analysis of teak (Tectona grandis) from Central and Peninsular India show significant relationship with pre-monsoon and monsoon climate. Moisture index over the region indicates strong association with tree-ring variations rather than the direct influence of rainfall. It is evident that, two to three consecutive good monsoon years are capable of maintaining normal or above normal tree growth, even though the following year is low precipitation year.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2017년도 9th Asian Crop Science Association conference
• /
• pp.186-186
• /
• 2017

Relay intercropping system of direct seeded rice and winter cereal is labor saving cultivation and has high land use efficiency in Japan. In this system, rice seeds are direct seeded into inter-row space of winter cereals (wheat or barley) in March or April. If the direct seeding of rice is conducted before stem elongation phase or using suitable seeder, these are little effect to yield of winter cereals. Though the seeds are generally thiuram treated, it's a matter that seedling establishment rate (SER) of direct seeded rice is low and unstable. The cause of low SER has not been revealed. In present study, with the aim to reveal causes of low SER, we conducted experiments and investigated the SER, and analyzed some factors that might affect SER. Experiment1: In 2015, 2016, we buried rice seeds underground, and investigated the transition of the seed survival rates (SSR). Seeds were thiuram-treated or non-treated. In 2 periods, SSR of thiuram-treated seeds were significantly higher than non-treated seeds. In 2016, thiuram-treated seeds were high in SSR (almost 75%) at April 30th, but low SER (10~27%) after harvest of winter cereals. Therefore, almost all of seed death might have been happen after germination. Analysis 1: We investigated the SER and cultivation conditions in Ibaraki pref. for several years. Meteorological factors were referred from the nearest point of AMeDAS. From mean temperature (MT) among 5days after and before the day, we divided the period of seeding ~June 20 to phase1~4. We defined each phase as below; Phase1: $MT{\leq}10^{\circ}C$, Phase2: $10^{\circ}C<MT{\leq}15^{\circ}C$, Phase3:$15^{\circ}C<MT{\leq}20^{\circ}C$, Phase4: $MT>20^{\circ}C$. We analyzed the correlation of SER and meteorological factors by each phase. Total number of days in phase 1~4 was significantly negative correlated with SER. In phase1, total rain fall and number of soil wetting days were significantly negative correlated with SER. In phase2~4, only MT was significantly positive correlated with SER. This result suggested that rainfalls in phase1 declined seed vigor to emergence from soil surface, by repeated water absorption and re-dry. From these present studies, it was suggested that one of factors of low SER of direct seeded rice in relay intercropping system is changing of water condition by rainfalls in phase1 ($MT{\leq}10^{\circ}C$). To improve SER, it's necessary to consider something seed treatments such as prevent water absorption during phase1. However, 58~60% of seeds seemed to die during May. It's suggested that, if seeds are thiuram treated, almost all of seeds can germinate underground, but the seed vigor to emergence from soil surface are insufficient. Further studies are needed to reveal the rest causes that is happening during emergence from soil surface.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권4호
• /
• pp.312-317
• /
• 2004

High dose ($3{\times}10^{16}cm^{-2}$) implantation of Fe or Ni ions into bulk, single-crystal ZnO substrates was carried out at substrate temperature of ${\sim}350^{\circ}C$ to avoid amorphization of the implanted region. The samples were subsequently annealed at $700^{\circ}C$ to repair some of the residual implant damage. X-Ray Diffraction did not show any evidence of secondary phase formation in the ZnO. The Ni implanted samples remained paramagnetic but the Fe-implanted ZnO showed evidence of ferromagnetism with an approximate Curie temperature of ${\sim}$240K. Preliminary X-Ray Photoelectron Spectroscopy measurements showed the Fe to be ill the 2+ oxidation state. The earrler density in the implanted region still appears to be too low to support carrier-meditated origin of the ferromagnetism and formation of bound magnetic polarons may be one potential explanation for the observed magnetic properties, No evidence of the Anomalous Hall Effect could be found in the Fe-implanted ZnO, but its transport properties were dominated by the conventional or ordinary Hall effect.