• 제목/요약/키워드: High Vibration

검색결과 4,246건 처리시간 0.035초

중력하중 설계된 1:5 축소 3층 철근콘크리트 골조의 지진모의실험 (Earthquake Simulation Tests of A 1:5 Scale Gravity Load Designed 3-Story Reinforced Concrete Frame)

  • 이한선;우성우
    • 콘크리트학회지
    • /
    • 제10권6호
    • /
    • pp.241-252
    • /
    • 1998
  • 이 연구의목적은 여러 수준의 지진에 대한 비내진 상세를 가진 저층 모멘트 저항 골조의 실제 반응을 관찰하기 위한 것이다. 우선 모델에 대한 축소율은 사용된 진동대의 용량을 고려하여 1 : 5 로 결정하였으며 상사성의 법칙에 따라 모델을 제작하였다. 그 다음에 이 모델에 대해 Taft N21E 지진가속도 기록의 최대 지진가속도를 0.12g. 0.2g, 0.4g로 조정하여 진동대를 이용한 지진모의실험을 수행하였다. 각 층별 횡방향 가속도와 변위, 그리고 구조물의 취약부위에서 국부변형이 측정되었다. 밑면 전단력은 손수 만든 로드셀을 이용하여 측정하엿다. 각 지진모의실험 전과 후에는 고유주기와 감쇠비의 변화를 살펴보기 위해 자유진동실험을 수행하였다. 전체거동과 국부거동에 대한 실험결과를 분석한 결과, 이 모델은 우리나라의 현행 내진 설계 기준에서의 설계지진 즉, 0.12g의 최대 지진가속에 대해서는 선형탄성으로 거동하였다. 최대 밑면 전단력은 1.8tf 로 설계 밑면 전단력의 약 4.7배로나타났다.이 실험모델은 높은 수준의 지진모의실험에서도 양호한 성능을 나타내었다. 높은 수준의지진에 대한 저항의 주요요소는 1)높은 초과강도, 2)기본주기의 증가, 그리고 3)비탄성 변형에 의한 얼마간의 에너지소산이다. 이 실험에서 모델의 층간변위는 대략 허용한계 내에 있었다.

PZT 라미네이트 Trapezoidal Piezoelectric Cantilever Generator의 모드(3-1, 3-3)별 에너지 하베스팅 특성 비교 (Comparison of Energy Harvesting Characteristics in Trapezoidal Piezoelectric Cantilever Generator with PZT Laminate Film by Longitudinal (3-3) Mode and Transverse (3-1) Mode)

  • 이민선;김창일;윤지선;박운익;홍연우;백종후;조정호;박용호;정영훈
    • 한국전기전자재료학회논문지
    • /
    • 제30권12호
    • /
    • pp.768-775
    • /
    • 2017
  • Energy harvesting characteristics of trapezoidal piezoelectric cantilever generator, which has a lead zirconate titanate (PZT) laminate film, were compared by longitudinal (3-3) and transverse (3-1) modes. The PZT laminate film, fabricated by a conventional tape casting process, was cofired with Ag electrode at $850^{\circ}C$ for 2 h. A multi-layered Ag electrode by a planar pattern and an interdigitated pattern was applied to the PZT laminate to implement the 3-3 and 3-1 modes, respectively. The energy harvesting performance of the 3-3 mode trapezoidal piezoelectric cantilever generator was better than that of the 3-1 mode. An extremely high output power density of $26.7mW/cm^3$ for the 3-3 mode was obtained at a resonant frequency of 145 Hz under a load resistance of $50{\Omega}$ and acceleration of 1.3 G, which is ~3-times higher than that for the 3-1 mode. Therefore, the 3-3 mode is considered significantly efficient for application to high-performance piezoelectric cantilever generator.

원심주조방식과 레이저 클래딩 증착법을 통한 화이트메탈의 기계 및 마찰특성 비교 (Comparison of Mechanical properties and Surface Friction of White Metals Produced by Centrifugal and Laser Cladded on SCM440)

  • 정재일;김동혁;박진영;오주영;최시근;김석삼;조영태;이호;함승식;김종형
    • Tribology and Lubricants
    • /
    • 제34권3호
    • /
    • pp.84-92
    • /
    • 2018
  • Bearings are essential for reducing vibration and wear, in order to achieve high durability and increase longevity. White metal treatment of tilting pads via centrifugal casting method has the possibility of increasing durability. However, this manufacturing method has drawbacks such as long processing time, high defect rate, and harmful health effects. Laser cladding deposition technique is a powerful method that can address these issues by decreasing the processing time and providing good adhesion. In this study, we suggest optimum conditions for laser cladding deposition that can be used in industrial applications. We deposited a soft white metal layer on SCM440 that is primarily used in shafts to minimize wear of bearing pads. During the laser deposition process, we controlled factors such as laser power, powder feed rate, and laser head speed to determine the optimum conditions. In addition, we measured the hardness using micro Vickers, and performed field emission scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and friction tests to investigate the mechanical properties and surface characteristics for different parameters. Based on the experimental results, we suggest that laser power, powder feed rate, and laser head speed of 1.3 kW, 2.5 rpm, and 10 mm/s, respectively, constitute the optimum conditions for producing white metals using laser cladding.

고성능 플래시 메모리 솔리드 스테이트 디스크 (A High Performance Flash Memory Solid State Disk)

  • 윤진혁;남이현;성윤제;김홍석;민상렬;조유근
    • 한국정보과학회논문지:컴퓨팅의 실제 및 레터
    • /
    • 제14권4호
    • /
    • pp.378-388
    • /
    • 2008
  • 플래시 메모리는 전력 소모가 작고 충격과 진동에 강하며 크기가 작다는 특성 때문에 최근 노트북이나 UMPC(Ultra Mobile PC)와 같은 이동 컴퓨팅 시스템에서 하드디스크를 대체할 대용량 저장 매체로서 주목 받고 있다. 플래시 메모리에 기반한 저장 장치는 일반적으로 랜덤 읽기 성능이나 순차 읽기, 순차 쓰기 성능이 매우 좋은데 비해, 덮어쓰기가 불가능한 플래시 메모리의 물리적인 제약으로 인하여 소량의 랜덤 쓰기 성능은 떨어진다. 본 논문은 이 문제를 해결하기 위한 두 가지 중요한 특징을 갖는 SSD(Solid State Disk) 아키텍처를 제안하였다. 첫 번째로 비휘발성 이면서도 SRAM과 동일한 인터페이스로 덮어쓰기가 가능한 작은 크기의 FRAM(Ferroelectric RAM)을 NAND 플래시 메모리와 함께 사용하여 소량 쓰기 오버헤드를 최소화하였다. 두 번째, 호스트 쓰기 요청들도 소량 랜덤 쓰기와 대량 순차 쓰기로 분류하여 각각에 대해 최적의 쓰기 버퍼 관리 방법을 적용하였다. 평가 보드 상에서 SSD 프로토타입을 구현하고 PC 사용 환경의 워크로드에 기반한 벤치마크를 이용하여 성능을 평가해 본 결과 랜덤 패턴을 보이는 워크로드에서는 하드디스크나 기존의 상용 SSD들에 비해 처리율(throughput) 측면에서 3배 이상의 성능을 보였다.

화순 폐탄광지역 광산배수와 침전 및 증발잔류광물에 대한 지구화학적 및 광물학적 연구 (Geochemistry and Mineralogy of Mine Drainage Water Precipitate and Evaporite Minerals in the Hwasoon Area)

  • 박천영;정연중;강지성
    • 자원환경지질
    • /
    • 제33권5호
    • /
    • pp.391-404
    • /
    • 2000
  • This study investigated the geochemical characteristics of mine drainage discharged from an abandoned coal mine in the Hwasoon area. Surface water samples were collected from 23 locations along the Hancheon creek. The concentration of Zn and Cu in stream waters was highest at low pH (3.53), whereas the content of TDS and TDI was highest at high pH (7.78) due to the concentration of Ca, $HCO_3$ and $SO_4$. At the upstream site, the Ba, Fe, Mn, Zn, and $SO_4$ contents were relatively high but decreased significantly with the distance from the coal mine. On the contrary, the Na and $NO_3$ contents were low at the upstream site but increased downstream. Yellow precipitate material collected in the Hancheon consisted mainly of iron and LOI. This yellow precipitate was heated from 100 to $900^{\circ}C$ for 1 hour. With increasing temperature, the intensity of hematite peaks were sharply produced in X-ray pattern and the absorption band Fe-O of hematite increased in IR due to dehydration and melting. The yellow to brown precipitate and evaporite materials were collected by a air-dry from the acid mine water at the laboratory. After drying, the concentration of ions in the acid water samples increased progressively in oversaturation with respect to either gypsum, ferrohexahydrite or quenstedetite. The X-ray powder diffraction studies identified that the precipitated and evaporated materials after drying were well crystallized gypsum, ferrohexahydrite and quenstedetite. Diagnostic peaks used for identification of gypsum were the 7.65, 4.28, 3.03, 2.87 and 2.48$\AA$ peaks and those for ferrohexahydrite were the 5.46, 5.12, 4.89, 4.44, 4.05, 3.62, 3.46, 3.40, 3.20, 3.03, 2.94, 2.53, 2.28, 2.07, 1.88 and 1.86${\AA} peaks. The IR spectra with OH-stretching, deformation of $H_2O$and ${SO_4}^{2-}$stretching vibration include the existence of gypsum, ferrohexahydrite and quenstedetite in the precipitated and evaporite materials. In the SEM and EDS analysis for the evaporite material, gypsum with well-crystallized, acicular, and columnar form was distinctly observed.

  • PDF

10 kWh급 초전도 베어링 회전자의 기계적 특성 평가 (Mechanical Properties of a High-temperature Superconductor Bearing Rotor in a 10 kWh Class Superconductor Flywheel Energy Storage System)

  • 박병준;정세용;김철희;한상철;박병철;한상진;두승규;한영희
    • Progress in Superconductivity
    • /
    • 제13권1호
    • /
    • pp.58-63
    • /
    • 2011
  • Recently, superconductor flywheel energy storage systems (SFESs) have been developed for application to a regenerative power of train, a power quality improvement, the storage of distributed power sources such as solar and wind power, and a load leveling. As the high temperature superconductor (HTS) bearings offer dynamic stability without the use of active control, accurate analysis of the HTS bearing is very important for application to SFESs. Mechanical property of a HTS bearing is the main index for evaluating the capacity of an HTS bearing and is determined by the interaction between the HTS bulks and the permanent magnet (PM) rotor. HTS bearing rotor consists of PM and iron collector and the proper dimension design of them is very important to determine a supporting characteristics. In this study, we have optimized a rotor magnet array, which depends on the limited bulk size and performed various dimension layouts for thickness of the pole pitch and iron collector. HTS bearing rotor was installed into a single axis universal test machine for a stiffness test. A hydraulic pump was used to control the amplitude and frequency of the rotor vibration. As a result, the stiffness result showed a large difference more than 30 % according to the thickness of permanent magnet and iron collector. This is closely related to the bulk stiffness controlled by flux pining area, which is limited by the total bulk dimension. Finally, the optimized HTS bearing rotor was installed into a flywheel system for a dynamic stability test. We discussed the dynamic properties of the superconductor bearing rotor and these results can be used for the optimal design of HTS bearings of the 10kWh SFESs.

폴리머 계열 방음패널의 차음특성 비교 분석 (Sound Insulation Properties of Polymer Soundproof Panels)

  • 이우미;이주행;손진희;김일호;박재로;김광수
    • 대한환경공학회지
    • /
    • 제35권8호
    • /
    • pp.592-597
    • /
    • 2013
  • 방음패널의 차음특성은 재료의 면밀도와 소음의 주파수와 높은 상관관계가 있으므로 방음패널의 두께 및 재료의 선택에 있어 실제 도로소음의 특성을 반영하는 것은 매우 중요하다. 본 연구에서는 재료의 경량 및 시공측면에서 수요가 증가하고 있는 플라스틱 소재 중 방음패널로 활용 가능한 소재를 선정하여 도로교통 소음의 주파수에 따른 차음특성을 평가하였다. 대상 패널은 물리적 특성을 조사하여 효율성 및 경제성 평가를 통해 polypropylene (PP)과 high-density polyethylene (HDPE)를 선정하였고 현재 방음패널의 재료로 사용되고 있는 polycarbonate (PC)와 polymethyl methacrylate (PMMA)와의 재료 및 두께에 따른 차음특성을 비교하였다. 그 결과 방음패널의 차음특성은 재료의 면밀도에 비례하여 PC, PMMA, HDPE, 그리고 PP순으로 높은 투과손실치를 나타내었다. 두께별 차음특성의 경우, 방음패널 두께에 비례하여 투과손실이 증가하나 일치효과로 인해 투과손실이 감소하는 주파수가 낮아짐을 확인할 수 있었다. 결론적으로, 저감하고자 하는 소음의 주파수대역을 먼저 파악하고 방음패널의 재질과 두께에 따른 주파수별 차음특성을 파악하여 적용한다면 효과적으로 소음을 저감할 수 있을 것으로 판단된다.

터보분자펌프(TMP) 배기속도 측정에 관한 고찰 (Study on the Measurement of TMP Pumping Speed)

  • 강상백;신진현;차덕준;고득용;정완섭;임종연
    • 한국진공학회지
    • /
    • 제19권4호
    • /
    • pp.249-255
    • /
    • 2010
  • 터보분자펌프(TMP)의 특성평가는 ISO, PNEUROP, DIN, JIS, AVS 등 세계 여러 나라의 표준제정기구에서 제정한 국제규격에 그 근거를 두고 있다. 한국표준과학연구원에서는 이러한 국제규격에 기반을 둔 터보분자펌프의 특성평가시스템을 자체 설계/제작하여 그 신뢰성을 확인하기 위해 개발품 및 상용품의 평가에 주력하고 있다. 터보분자펌프의 배기속도 측정방법으로서 기체흐름 영역에 따른 throughput method와 orifice method를 적용하고 있으나 측정게이지, 유량계 및 orifice conductance의 불확도 등 실질적으로 정확한 배기속도를 제시하기 위한 조건들의 제약 때문에 많은 측정오차를 포함하고 있다고 볼 수 있다. 이러한 배기속도의 측정오차를 줄이기 위한 하나의 고찰로서 본 논문에서는 $10^{-1}$ Pa-L/s 영역까지의 유량 주입범위를 가지는 기 구축된 정적법을 이용한 유량주입에 기반을 둔 throughput method를 이용하여 1000 L/s TMP의 측정 능력을 검증하고자 한다. 또한 분자류 영역인 orifice method를 사용할 경우 고진공영역, 미세유량 주입영역으로 진입할수록 커질 수밖에 없는 배기속도 측정 불확도를 최소화시키기 위해 검증된 유량을 이용한 conductance 값을 제시하여, 기 언급한 두 가지 배기 속도 측정 방법의 연속성을 유지하기 위한 실험적인 방법론을 제기하고자 한다.

부분 유입 노즐을 적용한 초임계 이산화탄소 발전용 초고속 터보발전기 개발 연구 (Research on Development of Turbo-generator with Partial Admission Nozzle for Supercritical CO2 Power Generation)

  • 조준현;신형기;강영석;김병휘;이길봉;백영진
    • 대한기계학회논문집B
    • /
    • 제41권4호
    • /
    • pp.293-301
    • /
    • 2017
  • 초임계 이산화탄소 발전사이클의 다양한 특성을 분석하기 위하여 Sub-kWe급의 소형 실험장치를 설계, 제작하였으며, 터보발전기를 개발하였다. 초임계 이산화탄소 발전용 터빈에서는 팽창비가 작고, 유량이 작기 때문에 터보발전기의 회전수가 높아지게 되고, 이에 따라 회전 부품의 선정, 터빈 공력설계, 축력 및 회전체 동역학 설계가 어려워지게 된다. 이에 터보발전기의 회전수를 줄이기 위하여 노즐의 여러 채널 중 1개의 노즐만 사용하는 부분유입 방법을 세계 최초로 초임계 이산화탄소 발전용 터보발전기에 적용하였으며, 회전체의 진동을 측정하여 부분유입 노즐을 적용함에도 회전체 안정성은 허용 범위내에 있음을 확인하였다.

헬리컬기어의 동적해석을 통한 전달오차 예측 (Prediction of Transmission Error Using Dynamic Analysis of a Helical Gear)

  • 이정석;윤문영;부광석;김흥섭
    • 대한기계학회논문집A
    • /
    • 제40권12호
    • /
    • pp.1005-1011
    • /
    • 2016
  • 기어소음의 근본적인 원인은 전달오차로 인해 발생하게 된다. 전달오차는 기어가 맞물릴 때 발생하는데 크게 정적전달오차와 동적전달오차가 있다. 이러한 오차들은 기어 이빨의 처짐 또는 치면 마찰에 의해 발생하고 이 요인들이 원인이 되어 기어 시스템에 진동이 발생하게 된다. 그리고 이 진동이 기어의 축으로 이동하게 되어 축을 떠받치고 있는 베어링에 전달되고 베어링에 전달된 가진은 최종적으로 기어의 케이싱으로 이동하게 되어 소음을 방출하게 된다. 본 논문에서는 이러한 전달오차에 의해 발생하는 최대 굽힘응력을 가지는 롤각을 찾기 위한 응력해석을 수행되었다. 본 논문에서는 이론적 바탕으로 설계되어 인볼류트 곡선을 가진 기어와 수정된 치형을 가진 기어의 전달오차에 대한 해석을 진행하였다. 또한, 급작스러운 작동이나 큰 백래쉬로 인해 발생하는 충격강도에 대한 영향을 알아보기 위해 유한요소해석을 통해 각각 정적 최대굽힘응력과 동적 최대굽힘응력의 결과를 이용하여 충격인자 값을 예측해 보았다.