• 한국가구학회지
• /
• 제19권3호
• /
• pp.172-179
• /
• 2008

The objective of this study was to investigate the influence of the water repellents' treatment on the water absorptivity and the dimensional stability of Korean red pine wood(Pinus densiflora). The alkylketene dimer(AKD), fluororesin emulsion(Wood-seal, WS), and paraffin wax emulsions(PW25, PW40, and PW1200) were used as water repellents. PW40 and WS were proved as excellent water repellents for pine wood, because the samples treated with these agents showed high contact angles and large reduction in water absorptivities. Also, the dimensional stability(antiswelling efficiency) of pine wood was considerably improved by water repellents treatments, such as PW40 and WS at the pressure of 2MPa. The water repellent treated woods with WS, PW40, and PW1200 at the pressure of 2MPa were relatively stable to the wet-dry cyclic leaching test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.442-447
• /
• 2007

A very abnormal vibration was occurred at the LP(low pressure) turbine continuously during the pre-operation for a 550MW class USC(ultra super critical) steam turbine. This vibration was initiated at the rotating speed of about 3,450rpm and then the vibration amplitude was highly increased the number by $2{\sim}3$ times with the increase of the rotating speed to the rated speed(3,600rpm). In this paper, this abnormal vibration named spike vibration. This spike vibration was caused by the rubbing between the rotating bucket tip seal and the Lower Half of spill strip. Also, this paper presents the mechanism of the spike vibration and the proper method to eliminate this abnormal vibration problem. This result would be good practice to find the solution of similar high vibration in the USC steam turbines for power plant as well as industrial rotating machineries.

• 한국소음진동공학회논문집
• /
• 제17권12호
• /
• pp.1238-1245
• /
• 2007

A very abnormal vibration was occurred at the LP(low pressure) turbine continuously during the pre-operation for a 550MW class USC(ultra super critical) steam turbine. This vibration was initiated at the rotating speed of about 3,450 rpm and then the vibration amplitude was highly increased the number by $2{\sim}3$ times with the increase of the rotating speed to the rated speed (3,600 rpm). In this paper, this abnormal vibration named spike vibration. This spike vibration was caused by the rubbing between the rotating bucket tip seal and the lower half of spill strip. Also, this paper presents the mechanism of the spike vibration and the proper method to eliminate this abnormal vibration problem. This result would be good practice to find the solution of similar high vibration in the USC steam turbines for power plant as well as industrial rotating machineries.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.366-370
• /
• 2007

Silicon nitride ($Si_3N_4$) ceramics have been considered for various components of nuclear power plants such as the mechanical seal of a reactor coolant pump (RCP), the guide roller for a control rod drive mechanism (CRDM), and a seal support, etc. Corrosion behavior of $Si_3N_4$ ceramics in a high-temperature and high-pressure water must be elucidated before they can be considered as components for nuclear power plants. In this study, the corrosion behaviors of $Si_3N_4$ ceramics containing MgO and $Al_2O_3$ as sintering aids were investigated at a hydrothermal condition ($300^{\circ}C$, 9.0 MPa) in pure water and 35 ppm LiOH solution. The corrosion reactions were controlled by a diffusion of the reactive species and/or products through the corroded layer. The grain-boundary phase was preferentially corroded in pure water whereas the $Si_3N_4$ grain seemed to be corroded at a similar rate to the grain-boundary phase in LiOH solution. Flexural strengths of the $Si_3N_4$ ceramics were significantly degraded due to the corrosion reaction. Results of this study imply that a variation of the sintering aids and/or a control (e.g., crystallization) of the grain-boundary phase are necessary to increase the corrosion resistance of $Si_3N_4$ ceramics in a high-temperature water.

• Tribology and Lubricants
• /
• 제21권4호
• /
• pp.171-176
• /
• 2005

O-ring seal is an essential component in various mechanical apparatuses for a sealing of oil container and pressure vessels. This paper presents the sealing pressure and compressive contact behaviors of hi-polymer O-rings, which is made by an outer shell of FFKM material and an inner solid ring of FKM one. The contact normal pressure and its ratios are measured by experimental method with an automatic control system of the working temperature and analyzed numerically by using the non-linear Marc FEM program. The results show reasonably good agreements between the computed FEM results and measured ones when the operating temperature is kom normal temperature of $18^{\circ}C$ and a high temperature of $300^{\circ}C$ But the compared values between the computed and tested results show a little difference because of the increased temperature, which is related to the non-linear parameter of the O-ring material. Bi-polymer 0-ring shows a good contact normal stress and compression behavior for a given operation temperature and compression ratio.

• 한국분무공학회지
• /
• 제18권1호
• /
• pp.55-60
• /
• 2013

In this study, injection flow rates and material of the solenoid sealing of the injectors were improved for the development of a di-methyl Ether(DME) common-rail system. To deliver the same amount of energy provided by injection pressure of diesel $P_{inj}$ = 160 MPa, the DME injectors need to have larger diameter of nozzle hole and more No. of hole at low injection pressure of $P_{inj}$ = 40~50 MPa. The simplified nozzle flow model, which takes account of nozzle geometry and injection condition, was employed in order to design the concept of a injector nozzle such as No. of hole, diameter of hole and diameter of needle seat, etc. Injection amount and rate were tested by diesel and DME test stand. As a result, the diameter of nozzle hole were enlarged by 0.25 mm. The diameter of the orifice in the high pressure line was increased by 1.0 mm to maintain hydraulic force in the nozzle. The material of the solenoid sealing was changed to HNBR, which was strong against the corrosive. Experimental results showed that the injection amount of the DME injector drastically increased by 191.9% comparison to that of diesel at $P_{inj}$ = 40 MPa.

• Computers and Concrete
• /
• 제20권3호
• /
• pp.275-282
• /
• 2017

Grouting is an operation often carried out to consolidate and seal the rock mass in dam sites and tunnels. One of the important parameters in this operation is grouting pressure. In this paper, analytical models used to estimate pressure are investigated. To validate these models, grouting data obtained from Seymareh and Aghbolagh dams were used. Calculations showed that P-3 model from Groundy and P-25 model obtained from the results of grouting in Iran yield the most accurate predictions of the pressure and measurement errors compared to the real values in P-25 model in this dams are 12 and 14.33 Percent and in p-3 model are 12.25 and 16.66 respectively. Also, SPSS software was applied to define the optimum relation for pressure estimation. The results showed a high correlation between the pressure with the depth of the section, the amount of water take, rock quality degree and grout volume, so that the square of the multiple correlation coefficient among the parameters in this dams were 0.932 and 0.864, respectively. This indicates that regression results can be used to predict the amount of pressure. Eventually, the relationship between the parameters was obtained with the correlation coefficient equal to 0.916 based on the data from both dams generally and shows that there is a desirable correlation between the parameters. The outputs of the program led to the multiple linear regression equation of P=0.403 Depth+0.013 RQD+0.011 LU-0.109 V+0.31 that can be used in estimating the pressure.

• 한국추진공학회지
• /
• 제17권3호
• /
• pp.15-20
• /
• 2013

Graphite는 고온/고압의 가스가 추진기관 내의 구동장치에 유입되지 않게 기밀 소재로 사용되며, 마모 과정에서 윤활막을 형성하여 구조물 안에서 윤활과 기밀을 돕는다. 본 연구는 기밀 소재로 사용되는 Graphite의 고온 마모 시험을 통해 고온 마모 특성을 평가하였다. 고밀도 Graphite (HK-6)에 대하여 실제 작동환경에 기초 한 온도, 미끄럼 속도, 접촉 하중 조건에 따른 마모 특성을 평가 및 고찰하였다. 마모 표면 관찰을 통해 마모 메카니즘을 파악하고 고온 마모 특성을 통하여 최적화된 작동 환경 조건에 대하여 제안 하였다. 결과적으로, 상온에서 보다 고온 환경에서 윤활막 형성에 유리 하여 마찰 계수가 비교적 낮게 나타나는 것을 알 수 있다.

• 한국주조공학회지
• /
• 제42권4호
• /
• pp.218-225
• /
• 2022

본 연구에서는 고압 다이캐스팅 (High pressure die-casting, HPDC)을 통해 알루미늄 합금 (상업코드: ALDC12종)으로 수소 자동차용 부품 (Air pressure control valve housing, APCVH)을 제조하였으며 주조품의 기밀성을 향상시키기 위해 유기 함침액을 개발하였다. 개발된 2종류의 유기 함침액 (INNO-series, 한국)과 상용 합침액 (P601, 일본)을 사용하여 함침공정 조건 및 후 처리에 따른 미세결함과 기밀성을 비교 평가하였다. 컴퓨터 단층촬영 및 3차원 X-선 현미경 분석을 통해 함침된 알루미늄 주조품의 결함제어 및 성능 개선을 확인하였다. 또한, 함침 공정 후 기밀성 시험에서 INNO-01이 함침된 시료의 경우 성능 개선율이 70%인 것으로 확인하였다. 따라서, 개발된 유기 함침액은 상용 가능하며 다이캐스팅 제품의 기밀성 향상에 도움이 될 것으로 판단된다.

• 한국식품과학회지
• /
• 제43권3호
• /
• pp.321-328
• /
• 2011

본 연구에서는 대추를 필름 형태의 식품 소재로 개발하였다. 대추 필름 제작에 고분자 분쇄 방법으로 사용된 HPH는 대추 필름의 인장 강도와 수분 투과도를 향상시켰다. 기존에 개발된 많은 다른 생고분자 필름보다 높은 인장 강도와 낮은 수분 투과도는 열접합강도와 함께 식품에 있어 HPH 대추 필름의 상업적 적용 가능성을 보여주었다. 대추 필름은 대추 고유의 형태와 크기에 제한 없이 여러 식품에 코팅 또는 롤 형태로 사용될 수 있을 것으로 기대된다.