• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.4_1
• /
• pp.377-385
• /
• 2021

High voltage direct current(HVDC) systems has been an alternative method of a power transmission to replace high voltage alternate current(HVAC), which is a traditional AC transmission method. Due to technical limitations, Line commutate converter HVDC(LCC-HVDC) was mainly used. However, result from many structural problems of LCC-HVDC, the voltage source converter HVDC(VSC-HVDC) are studied and applied recently. In this paper, after analyzing the reactive power and output voltage ripple, which are the main problems of LCC-HVDC, the characteristics of each HVDC are summarized. Based on this result, a new LCC-HVDC structure is proposed by combining LCC-HVDC with the MMC structure, which is a representative VSC-HVDC topology. The proposed structure generates lower reactive power than the conventional method, and greatly reduces the 12th harmonic, a major component of output voltage ripple. In addition, it can be easily applied to the already installed LCC-HVDC. When the proposed method is applied, the control of the reactive power compensator becomes unnecessary, and there is an advantage that the cut-off frequency of the output DC filter can be designed smaller. The validity of the proposed LCC-HVDC is verified through simulation and experiments.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.176-181
• /
• 1998

The parallel inverter is popularly used because of its fault-tolerance capability, high-current outputs at constant voltages and system modularity. The conventional parallel inverter usually employs active and reactive power control of frequency and voltage droop control. However, these approaches have the disadvantages that the response time of parallel inverter control is slow against load and system parameter variation to calculate active, reactive power, frequency and voltage. This paper describes a novel control scheme for power equalization in parallel-connected inverter. The proposed scheme has a fast power balance control response, a simplicity of implementation, and inherent peak current limiting capability since it employees an instantaneous current/voltage control with output voltage and current balance and output voltage regulation. A design procedure for the proposed parallel inverter controller is presented. Furthermore, the proposed control scheme is verified through the experiment in various cases such as the system parameter variation, the control parameter variation and the nonlinear load condition.

• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.689-698
• /
• 2012

This paper investigates the effects of applying different input current waveshapes on the performance of a continuous-conduction-mode (CCM) power-factor-correction (PFC) boost pre-regulator. It is found that the output voltage ripple of the pre-regulator can be reduced if the input current is modified to include controlled amount of higher order harmonics. This finding allows us to balance the performance of output regulation and the harmonic current emission when coming to the design of the pre-regulator. An experimental PFC boost pre-regulator prototype is constructed to verify the analysis and show the benefit of the pre-regulator operating with input current containing higher order harmonics.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.243-246
• /
• 1997

In this paper, soft switching high power factor buck converter is proposed. This converter is composed of diode rectifier, a input capacitor can be small enough to filter input capacitor can be small enough to filter input current, buck converter with loss less snubber circuit. Converter is operated in discontinous conduction mode, turn of of the switching device is a zero current switching(ZCS) and high power factor input is obtained. In addition, zero voltage switching(ZVS) at turn of is achieved and switching loss is reduced using loss less snubber circuit. The capacitor used in the snubber circuit raised output voltage. Therefore, proposed converter has higher output voltage and higher efficiency than conventional buck type converter at same duty factor in discontious conduction mode operation.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1489-1498
• /
• 2015

Gallium nitride (GaN)-based power switching devices, such as high-electron-mobility transistors (HEMT), provide significant performance improvements in terms of faster switching speed, zero reverse recovery, and lower on-state resistance compared with conventional silicon (Si) metal-oxide-semiconductor field-effect transistors (MOSFET). These benefits of GaN HEMTs further lead to low loss, high switching frequency, and high power density converters. Through simulation and experimentation, this research thoroughly contributes to the understanding of performance characterization including the efficiency, loss distribution, and thermal behavior of a 160-W GaN-based synchronous boost converter under various output voltage, load current, and switching frequency operations, as compared with the state-of-the-art Si technology. Original suggestions on design considerations to optimize the GaN converter performance are also provided.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.836-845
• /
• 2001

A Novel fully-differential bipolar current subtracter(FCS) and its application to current controlled current amplifier(CCCA) for high-accuracy current-mode signal processing were designed. To obtain full-differential current output, the FCS was symmetrically composed of two current follower with low current-input impedance. The CCCA to control output current by the bias current was consisted of the subtracter and a current gain amplifier(CGA) with single-ended current output.. The simulation result shows that the FCS has current-input impedance of 5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100 $\mu$A to 20 mA. The power dissipation of the FCS and CCCA are 1.8 mW and 3 mW, respectively.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.860-863
• /
• 2003

In this paper high power SMU(Source Measurement Unit) having 50V/1.5A source/measure range has been designed and implemented. The SMU has two operation mode, voltage mode and current mode. The SMU can be used as variable voltage source, variable current source, voltage meter, or current meter. Combining two different unit, output power can be doubled as 100V/1.5A. The developed SMU tan be used many semiconductor testing system and electronic device inspecting system.

• Journal of Sensor Science and Technology
• /
• v.29 no.5
• /
• pp.324-327
• /
• 2020

The impact of output conductance (g_o) on the short-circuit current-gain cut-off frequency (f_T) in In_0.8Ga_0.2As high-electron-mobility transistors (HEMTs) on an InP substrate was investigated. An attempted was made to extract the values of f_T in a simplified small-signal model (SSM) of the HEMTs, derive an analytical formula for f_T in terms of the extrinsic model parameters of the simplified SSM, which are related to the intrinsic model parameters of a general SSM, and verify its validity for devices with L_g from 260 to 25 nm. In long-channel devices, the effect of the intrinsic output conductance (g_oi) on f_T was negligible. This was because, from the simplified SSM perspective, three model parameters, such as g_{m_ext}, C_{gs_ext} and C_{gd_ext}, were weakly dependent on g_oi. However, in short-channel devices, g_oi was found to play a significant role in degrading f_T as L_g was scaled down. The increase in g_oi in short-channel devices caused a considerable reduction in g_{m_ext} and an overall increase in the total extrinsic gate capacitance, yielding a decrease in f_T with g_oi. Finally, the results were used to infer how f_T is influenced by g_oi in HEMTs, emphasizing that improving electrostatic integrity is also critical importance to benefit fully from scaling down L_g.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.514-517
• /
• 1996

Zero current switching(ZCS) series resonant converter is used to control laser power density in a pulsed Nd:YAG laser power supply. The high power and high repetition rate paused Nd:YAG laser is designed and fabricated to control current pulse width and pulse repetition rate in the double elliptical laser oscillator. In order to find out operational characteristics of pulsed Nd:YAG laser, the electrical properties of driving power supply and laser output power are investigated and experimented by changing of the current pulse width from 200uS to 350uS(step 50uS) and pulse repetition rate range of 500pps(pulse per second) to 1150pps. From that result, we obtaind maximum efficiency of 1.83% and maximum laser output or 220W at the condition of 350 uS and 1150pps with one Nd:YAG rod), and obtained that of more than 400W with two laser head connecting series.

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.4
• /
• pp.35-38
• /
• 2021

Conventional direct current (DC) rotating machines are usually used for crane and press machine using high torque in metal and steel industries, because of a constant output power along variable rotating speed. A general DC motor with permanent field magnets could not increase a magnetic flux density at a gap between armature coils and field magnets. However, a superconducting DC motor has field magnets composed with high temperature superconducting (HTS) coils and it could increase the magnetic flux density at the gap to over 10 times than those of a general DC motor by control the excitation current into HTS coils. The superconducting DC motor could be operated with extremely high torque and constant output power at a low rotational speed. In this paper, a 500 W superconducting DC rotating machine was conceptually designed with a LN₂ (Liquid Nitrogen) cooling method and the operation characteristics results of HTS field magnets were presented. The two no-insulation HTS magnets for a 500 W superconducting DC rotating machine were fabricated. The excitation current for the HTS magnets could be controlled from 0 to 40 A. This test results will be available to design large-sized HTS magnets for a number of hundred kW class superconducting DC rotating machine under LN₂ cooling system.