• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.12
• /
• pp.9-16
• /
• 2010

In this paper, we have proposed a new dimmable magnetic ballast for HID(High Intensity Discharge) lamps consisted of AC switches to variate inductance value by using Silicon Controlled Rectifiers and the isolated zero current detector on inductor. Conventional dimming ballast has used relays or Solid State Relays in AC switches. However, a relay is difficult to zero current switching, because it has long operating time(10[ms]), and price competitiveness of SSR is very low. The proposed AC switches are suitable to switch at zero inductor current and it is accurately detected by using a opto-coupler. SCR is cheaper than SSR, and it is suitable to switch at zero inductor current because SCR is automatically turned off under holding current at no gate signal. Operating principles, simulation results and experimental results of the proposed ballast are described.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.2
• /
• pp.69-76
• /
• 2013

In this paper, electronic ballast using resonant inverter for HID lamp is designed and implemented. The proposed electronic ballast is used the soft switching technology ZVS(Zero Voltage Switching) to reduce turn-on and turn-off loss. The ignition of proposed electronic ballast is achieved by controlling a full bridge inverter which is consisted of LC filter for resonance. After ignition the ballast operates as a low frequency square wave inverter by controlling a full bridge inverter as a buck converter. After ignition at resonant frequency of $f_o$=160kHz, the switching frequency of a buck converter is consisted of 50kHz of high frequency and 170Hz of low frequency. This is for attenuating high frequency harmonics and avoiding acoustic resonance. The experimental results show that electronic ballast using resonant inverter is operated stably.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.531-537
• /
• 2007

This paper presents a new method for determining L, Cs, and Cp in a series parallel resonant inverter. This inverter is suitable for driving high-intensity discharge (HID) lamps. The operating frequency is selected to avoid acoustic resonances which are governed by the size and shape of the arc tube. L, Cs and Cp, are chosen to satisfy the ignition and steady state requirements of the lamp. Equations are developed to analyze the starting condition and steady state operating condition of the lamp. For the prototype ballast for a 250W Metal Halide Lamp, experimental results are presented in order to validate the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.449-454
• /
• 1999

A new scheme of the automotive High Intensity Discharge (HlD) lamp ballast systems is proposed. The p proposed scheme consists of the high frequency IX DC converter and the low frequency DC-AC inverter, like t that the conventional HID ballast system. However, this system separates the input voltage of the ignitor from t the dc link voltage, which results in the use of lower voltage rating power devices for the HID lamp ballast s system, comparlu with convention띠 system. As a result, proposed system has a lower cost and higher e efficiency. This paper presents th$\varepsilon$ design and anlaysis of the propoSlU ballast and some 앉아、nmental results.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.160-162
• /
• 2004

The aim of this study is to make the technical standards for certificating a high efficiency metal-halide lamps and reflectors using the high intensity discharge lamps, to accomplish the practical energy saving effect. Metal-halide lamps are certificated by stabilzed and restarting time, lamp voltage, current, power and light output efficiency. The high illumination reflectors using HID lamps are certificated by testing reflective index, fading, the melting point, glare and install spacing factor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.4
• /
• pp.166-171
• /
• 2008

This paper presents high efficiency control system of automotive 35W electronic ballast for high intensity discharge(HID) lamp using switching flyback converter with variable frequency. Considering performance, size and efficiency of ballast, the flyback converter is designed with planar transformer in converter stage. HID lamp demands a highly efficient ballast and very complex control circuitry that can control complex transient state for applying to automotive. The proposed electronic ballast system is composed of a flyback converter using planar transformer, a full bridge inverter, and a step up igniter. In this system, switching frequency of flyback converter is controlled by varying input voltage of HID ballast and the price and the size of HID ballast using planar transformer can be reduced. The performance and efficiency of the posed system are verified through various the experiment results.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.12
• /
• pp.622-626
• /
• 2001

HID(high intensity discharge)lamps are high pressure mercury lamp, high pressure sodium lamp and metalhalide lamp. metalhalide lamp among these lamps has considered to be one of the most effective artificial light sources and this lamp has good efficiency, good color rendition and good focusing capability, But the shortcorning of metalhalide lamp is known as acoustic resonance phenomena in the discharge tube when lighted by electronic ballast and then acoustic resonance cause various problems such as the arc instability, light output fluctuations. In this paper, to reduce the acoustic resonence phenomena, the electronic ballast was designed by three methods for high frequency operation wish frequency-modulated sinusodial waves in acoustic resonance frequency band. These frequency-modulated methods are resonance frequency and resonance frequency, resonance frequency and non-resonance frequency non-resonance frequency and non-resonance frequency Experiment results could't show the Presence of acoustic resonance visually and it proved that the resonance-generating conditions can be avoided by continuously changing the two operating frequencies in acoustic resonance band (20.59kHz∼94.2kHz).

• Journal of the Korean Professional Engineers Association
• /
• v.42 no.5
• /
• pp.41-45
• /
• 2009

The last century of lighting has been dominated by incandescent, fluorescent and high-intensity discharge(HID)light sources. In the late 1970's, after green LEDs were invented, Dr. Ching Tang at Eastman Kodak discovered that sending an electrical impulse through carbon compound caused such material glow. Present day LED commercial packages have reached 100 lm/W, comparable to the efficacies of fluorescent and certain HID lamps. LED products available today are market as "Green-Industry" but actually low light output compared to typical light sources. The combination of high price and low light output make them a poor replacement for current technology. It is very important to compare new LED products to the most efficient conventional technology that could be used for any specific application. As LED technology advances, costs decrease, and efficiency improves, LEDs will build market share in the general illumination market.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.602-604
• /
• 2001

본 논문은 고압방전(HID)램프용 안정기의 효율을 향상시키기 위하여 자기식 안정기의 코아 및 코일의 권회수에 따른 특성을 분석하고 이를 바탕으로 코아를 설계하는 것이다. 코아의 재질 및 형상에 따른 자속분포를 자계해석 프로그램으로 해석하여, 기존 제품안정기 효율 90%에 비해 향상시킬수 있는 기초배경 및 설계 방안을 제시하였다.