• 청정기술
• /
• 제24권4호
• /
• pp.332-338
• /
• 2018

현재 리튬이온전지의 음극 소재 활물질로는 흑연이 주로 사용되고 있다. 그러나 흑연의 최대 이론 용량이 $372mA\;h\;g^{-1}$으로 제한되기 때문에 차세대 고용량 및 고에너지 밀도의 리튬이온전지 개발을 위해서는 새로운 음극 소재 활물질이 필요하다. 여러 음극 소재 활물질 중에서 Si의 최대 이론 용량은 $4200mA\;h\;g^{-1}$으로 흑연의 최대 이론 용량보다 약 10배 이상 높은 값을 나타내고 있지만 부피 팽창율이 거의 400%로 크기 때문에 사이클이 진행될수록 비가역 용량이 증가하여 충전 대비 방전 용량이 현저히 감소하는 현상을 나타내고 있다. 이러한 문제점을 해결하기 위한 방법으로 Si 음극 소재 활물질의 입자 크기를 조절하여 기계적 응력 및 반응상의 체적 변화를 감소시켜 사이클 특성을 다소 향상시킬 수 있다. 따라서 Si 입자의 부피 팽창율에 따른 충전 및 방전 용량의 감소를 최소화하기 위해 공정 시간 및 원가 절감이 우수한 건식 방법으로 Si을 분쇄하여 사이클 특성 향상에 관한 연구를 진행 하였다. 본 논문에서는 진동밀을 이용하여 Si을 나노 크기로 제어하고 실험 변수에 따른 재료들의 물리화학적 특성과 전기화학적 특성을 측정하였다.

• 한국전기전자재료학회논문지
• /
• 제32권3호
• /
• pp.252-255
• /
• 2019

Black phosphorus (BP) is a potential candidate for an anode in lithium ion batteries due to its high theoretical capacity and the large interlayer spacing in the monolayered phosphorene form, allowing for lithium intercalation/deintercalation. In this study, large-scale exfoliation of bulk BP was accomplished using a solution of NaOH and N-methyl-2-pyrrolidone (NMP), yielding phosphorene, which can be assembled into nanoflakes using electrophoretic deposition (EPD). Through the systematic addition of NaOH and subsequent sonication, BP nanoflakes were obtained in high yields by EPD, allowing for the integration of these nanoflakes into an anode in the film state. Anodes with a charge/discharge capacity of 172 mAh/g at a rate of 200 mA/g were obtained, which are promising for battery applications through various post-film treatments.

• Journal of Electrochemical Science and Technology
• /
• 제13권2호
• /
• pp.269-278
• /
• 2022

Utilization of high-voltage electrolyte additive(s) at a small fraction is a cost-effective strategy for a good solid electrolyte interphase (SEI) formation and performance improvement of a lithium-rich layered oxide-based high-energy lithium-ion cell by avoiding the occurrence of metal-dissolution that is one of the failure modes. To mitigate metal-dissolution, we explored fluorinated dual-additives of fluoroethylene carbonate (FEC) and di(2,2,2-trifluoroethyl)carbonate (DFDEC) for building-up of a good SEI in a 4.7 V full-cell that consists of high-capacity silicon-graphite composite (15 wt% Si/C/CF/C-graphite) anode and Li_1.13Mn_0.463Ni_0.203Co_0.203O₂ (LMNC) cathode. The full-cell including optimum fractions of dual-additives shows increased capacity to 228 mAhg^-1 at 0.2C and improved performance from the one in the base electrolyte. Surface analysis results find that the SEI stabilization of LMNC cathode induced by dual-additives leads to a suppression of soluble Mn²⁺-O formation at cathode surface, mitigating metal-dissolution event and crack formation as well as structural degradation. The SEI and structure of Si/C/CF/C-graphite anode is also stabilized by the effects of dual-additives, contributing to performance improvement. The data give insight into a basic understanding of cathode-electrolyte and anode-electrolyte interfacial processes and cathode-anode interaction that are critical factors affecting full-cell performance.

• Composites Research
• /
• 제35권6호
• /
• pp.365-370
• /
• 2022

전기자동차 및 E-모빌리티 시장이 급속히 성장함에 따라 리튬이온전지는 현재 가장 주목받는 기술 중 하나로 여겨지고 있다. 따라서 높은 용량 및 출력, 급속 충전 성능을 가지는 고에너지밀도 전극 개발이 매우 중요한 상황이다. 고에너지밀도 전극 구현을 위해서 음극의 경우 실리콘, 주석 등 고용량 활물질 소재에 대한 연구가 진행되고 있는 상황이다. 하지만 이러한 고용량 활물질 소재는 전지의 충방전 과정 시 발생하는 부피팽창이 전지의 성능을 저하시키는 주된 원인이 된다고 알려져 있다. 따라서 활물질의 부피팽창을 완화할 수 있는 바인더 소재 개발이 매우 중요한 상황이며, 기존 PVDF, CMC/SBR계 바인더 뿐만 아니라 수용성 고분자(polyacrylic acid, polyvinyl alcohol, aliginate 등)를 이용한 바인더 소재 개발 연구가 많이 보고되고 있다. 이처럼 앞으로 리튬이온전지의 고성능화를 위해서 바인더는 매우 중요한 기술이 되었으며, 본 논문에서는 리튬이온전지용 음극 바인더 소재의 연구 동향을 살펴보고자 한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2181-2185
• /
• 2008

Fuel processing systems which convert HC fuel into $H_2$ rich gas (such as stream reforming, partial oxidation, auto-thermal reforming) need high temperature environment($600-1000^{\circ}C$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1-5kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural & anode off gas as reformer fuel. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity.

• Journal of Electrochemical Science and Technology
• /
• 제7권2호
• /
• pp.170-178
• /
• 2016

Composited molybdenum oxide and amorphous carbon (MoO₃/C) as anode material for lithium ion batteries has been successfully synthesized by calcining polyaniline (PANI) doped with ammonium heptamolybdate tetrahydrate (AMo). The as prepared electrode material was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and field emission scanning electron microscopy (FE-SEM). The electrochemical performance of the anode was investigated by galvanostatic charge/discharge, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The MoO₃/C shows higher specific capacity, better cyclic performance and rate performance than pristine MoO₃ at room temperature. The electrochemical of MoO₃/C properties at various temperatures were also investigated. At elevated temperature, MoO₃/C exhibited higher specific capacity but suffered rapidly declines. While at low temperature, the electrochemical performance was mainly limited by the low kinetics of lithium ion diffusion and the high charge transfer resistance.

• 한국진공학회지
• /
• 제9권1호
• /
• pp.36-41
• /
• 2000

$SnO-2$ thin films for thin film secondary battery anode were deposited n glass substrate with stain-less steel collector and charge/discharge experiments were conducted to investigate feasibility of $SnO-2$ thin film as a new anode material. The as-deposited films were pure $SnO-2$ phase which is not related to deposition condition. The grain size on the surface of as-deposited films increased with increase of oxygen partial pressure. However, the grain size did not show any change above oxygen partial pressure of 80:20. The surface roughness of the as-deposited films increased after decreasing because of resputtering effect of oxygen negative ion in plasma. All films showed typical $SnO-2$ anode characteristics which has a side effect at the first cycle, which is not related to the deposition condition. The charge/discharge experiments of 200cycles indicated that capacity of $SnO-2$ films depended on oxygen contents and surface roughness. The cycle characteristics was determined by initial charge/discharge reaction. The $SnO-2$ film with low initial capacity showed more stable cycle characteristics than film with high initial capacity.

• Nano
• /
• 제13권12호
• /
• pp.1850139.1-1850139.10
• /
• 2018

$Co_3O_4$ nanocrystals have been synthesized via an ordinary one-step calcination of a cobalt-based 2D coordination polymer [Co(tfbdc)(4,4'-bpy)$(H_2O)_2$]. As an anode material for lithium-ion batteries, the obtained $Co_3O_4$ nanocrystals exhibit high reversible capacity, excellent cyclic stability and better rate capability. The reversible capacity of the $Co_3O_4$ nanocrystals maintains $713mA\;h\;g^{-1}$ after 50 cycles at a current density of $50mA\;g^{-1}$. Our results confirm that searching for metal oxides nanomaterials used as anode materials of lithium ion batteries via the calcinations of 2D coordination polymer is a new route.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권6호
• /
• pp.328-334
• /
• 2000

A lithium ion secondary battery using carbon as a negative electrode has been developed. Further improvements to increase the cell capacity are expected by modifying the structure of the carbonaceous material. There are hopes for the development of large capacity lithium ion secondary batteries with long cycle, high energy density, high power density, and high energy efficiency. In the present paper, needle cokes from petroleum were examined as an anode of lithium ion secondary battery. Petroleum cokes, MCL(Molten Caustic Leaching) treated in Korea Institute Energy Research, were carbonized at various temperatures of 0, 500, 700, $19700^{\circ}C$ at heating rate of $2^{\circ}C$/min for lh. The electrolyte was used lM liPF6 EC/DEC (1:1). The voltage range of charge & discharge was 0.0V(0.05V) ~ 2.0V. The treated petroleum coke at $700^{\circ}C$ had an initial capacity over 560mAh.g which beyond the theoretical maximum capacity, 372mAh/g for LiC6. This phenomena suggests that carbon materials with disordered structure had higher cell capacity than that the graphitic carbon materials.

• Corrosion Science and Technology
• /
• 제21권6호
• /
• pp.445-453
• /
• 2022

SiO_x was prepared from a mixture of Si and SiO₂ via high-energy ball milling as a negative electrode material for Li-ion batteries. The molar ratio of Si to SiO₂ as precursors and the milling time were varied to identify the synthetic condition that could exhibit desirable anode performances. With an appropriate milling time, the material showed a unique microstructure in which amorphous Si nanoparticles were intimately embedded within the SiO₂ matrix. The interface between the Si and SiO₂ was composed of silicon suboxides with Si oxidation states from 0 to +4 as proven by X-ray photoelectron spectroscopy and electrochemical analysis. With the addition of a conductive carbon (Super P carbon black) as a coating material, the SiO_x/C manifested superior specific capacity to a commercial SiO_x/C composite without compromising its cycle-life performance. The simple mechanochemical method described in this study will shed light on cost-effective synthesis of high-capacity silicon oxides as promising anode materials.