• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1615-1626
• /
• 1992

In this study, vibrations and resulting acoustic radiations from an elastic beam impacted by a steel ball were studied theoretically and experimentally. First the transverse vibrations of free-free elastic beams are analysed with modal analysis technique. The impact forces are modeled with the Hertz's theory and the contanct duration is compared with the measured values. Also the calculated beam vibrations are verified with the experimental results. Then the acoustic radiations due to the beam vibration are studied numberically and experimentally. The acousticpressure is calculated assuming the beam has an elliptical cross-section. The predicted acoustic pressure is compared with the measured value. It was found that both the predicted beamvibrations using the Hertz's theory and the estimated acoustic pressure under the assumption of an elliptical cross- section are in very good agreements with the measured values.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.816-821
• /
• 2005

The cycloid reducer has very high efficiency, high ratios, high stiffness and small size, in comparison with a conventional gear mechanism, which makes it an attractive candidate for limited space and precision application such as industrial robot. There are several publications on analysis and design of the cycloid reducer, however, it was assumed that the contact stiffness of pin rollers and cycloid disk is constant regardless of their contact geometry. Moreover, the torsional stiffness of the cycloid reducer couldn't be calculated due to the assumption. In this paper, we present a new procedure of calculating torsional stiffness of the cycloid reducer using Hertz contact theory. First, conventional force analysis of the cycloid reducer is briefly reviewed. Then, iterative numerical calculation procedure of the contact stiffness is proposed based on the Hertz contact theory where the contact stiffness depends on the contact force. In addition, total torsional stiffness of the cycloid reducer is estimated considering its rolling element bearing stiffness. The torsional stiffness of the cycloid reducer is dominated by the rolling element bearing stiffness since the contact stiffness of the cycloid disk is too large.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.219.1-219.1
• /
• 2005

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.838-843
• /
• 2008

Since thickness deformation and lateral deflection often occurs during the collision of flexible bodies, they should be considered simultaneously in the impact analysis. The thickness deformation, however, cannot be considered in beam/shell theory since the thickness is assumed to be constant in the theory. So, solid elements are employed to estimate the thickness deformation. However, the CPU time increases significantly if solid elements are employed. In the present study, a modeling method for the impact analysis of a flexible body employing Hertzian contact theory is presented. The efficiency and the accuracy of the modeling method are discussed with some numerical examples.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.623-630
• /
• 1995

The impulse response functions (force-strain relations) for Euler-Bernoulli and Timoshenko beams are considered. The response of a beam to a transverse impact force is numerically obtained with the convolution approach using the impulse response function obtained by Laplace transform. Using this relation, the impact force history is determined in the time domain and results are compared with those from Hertz's contact law. The parameters of timpact force model are identified using the recovered force and compared with the Hertz's contact model. In order to verify the proposed algorithm, measurements were done using an impact hammer and a steel ball drop test and these results are also compared with the simulated values.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.383-388
• /
• 2008

A modeling method for the impact analysis of plate structures employing Hertzian contact theory is presented in this paper. Since local deformation as well as bending deflection of the plate occurs due to the collision, it has to be considered for the impact analysis. When the coefficient of restitution is employed for the impact analysis, the local deformation is not considered. For more accurate and reliable impact analysis, however, the local deformation should be considered. The effects of the location of collision and the collision mass on the impact duration time and the contact force magnitude are investigated through numerical studies employing Hertzian contact theory.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.481-488
• /
• 1988

In the analysis of impulsive response of plate, Lagrange's theory, Reissner's theory and Mindlin's theory are generally used. But, in applying these theories the impulsive stresses directly underneath the concentrated impact point cannot be analyzed because the solution fails to converge. In this paper, therefore, an attempt for a supported square plate is made by using three-dimensional dynamic theory of elasticity on the supposition that the uniform distributed load acts on the central part of it. In order to clarify the validity of theoretical analysis, the strain variations are measured experimentally for a square glass plate. Finally it is shown that these theoretical results are in close agreement with the experimental results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.7
• /
• pp.275-286
• /
• 2001

The research presents an analytical theory to calculate the characteristics of the bal bearing with waviness in its rolling elements considering the centrifugal force and gyroscopic moment of bal. The effects of centrifugal force and gyroscopic moment are introduced to the kinematic constraints and force equilibrium equations. and the waviness of rolling elements is modeled by sinusoidal function to calculate the contact force at each ball. The numerical solutions of governing equation of berating due to waviness are calculated by using the Newton-Raphson method. The accuracy of the research is validated by comparing the contact force. contact angle in case of considering the centrifugal force and gyroscopic moment of bal and the contact force and vibration frequencies in cases of considering waviness with the prior researches respectively. It investigates the stiffness, contact force. displacement and vibration frequencies of the ball bearing considering not only the centrifugal force and gyroscopic moment of ball but also the waviness of the rolling elements.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.554-570
• /
• 1990

he rolling contact behaviors between a smooth ball and a flat rough surface under dynamic load are intricately affected by many factors, such as the diameter of a ball, normal load and the roughness of a flat surface etc. Accordingly, the experimental study is done to find them on the base of elastic hysteresis loss as theoretical approach is very difficult. The experimental apparatus composed of damped-free vibration system is used. This paper investigates the damping characteristics on the rolling contact area through rolling friction force and logarithmic decrement versus displacement obtained in accordance with the variations of those factors, and presents a new experimental method to find out contact width using the relations of logarithmic decrement and rolling friction force with displacement.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.148-156
• /
• 2000

In this paper, we investigate contact characteristic of wheel-rail interface for rolling stock using the finite element method. Contact stress distribution due to the rail mounting slope is obtained in order to reduce the contact stress. Stress analysis of the rail, firstly, is performed one subjected to elliptical pressure based on Hertz theory. Secondly, we perform stress analysis of the rail subjected to contact stress obtained by this study. Results for the maximum shear stress, its location and the principal shear stress distribution are compared.