• Nuclear Engineering and Technology
• /
• 제35권4호
• /
• pp.274-285
• /
• 2003

Film boiling heat transfer coefficients for a downward-facing hemispherical surface are measured from the quenching tests in DELTA (Downward-boiling Experimental Loop for Transient Analysis). Two test sections are made of copper to maintain Bi below 0.1. The outer diameters of the hemispheres are 120 mm and 294 mm, respectively. The thickness of both the test sections is 30 mm. The effect of diameter on film boiling heat transfer is quantified utilizing results obtained from the two test sections. The measured heat transfer coefficients for the test section with diameter 120 mm lie within the bounding values from the laminar film boiling analysis, while those for diameter 294 mm are found to be greater than the numerical results on account of the Helmholtz instability. There is little difference observed between the film boiling heat transfer coefficients measured from the two test sections. In addition, the higher thermal conductivity of copper results in the higher minimum heat flux in the tests. For the test section of diameter 120 mm, the Leidenfrost point is lower than that for the test section of diameter 294 mm. Destabilization of film boiling propagates radially inward for the 294 mm test section versus radially outward for the 120 mm Test Section.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.196-199
• /
• 2005

Flow traveling over a cavity opening forms a vortex due to unstable shear layer and induces an aerodynamic pressure excitation from the diffusion of the vortex convecting out of the trailing edge of the opening. The interaction between the excitation force and the cavity response sustains resonance in the resonator(cavity) and locked-in vortex shedding at the leading edge of the opening. The aerodynamic excitation force can be described from the diffusion of the vortex over the trailing edge and the level of its diffusivity is related to the strength of vorticity seeded at the loading edge. In this study, the control scheme of the internal pressure oscillation was proposed from regulating the vorticity at the leading edge by use of an oscillating spoiler. It was found that the relative motion between the spoiler and the air mass at the cavity opening influenced vorticity strength and the control was achieved by direct feedback of the cavity pressure fluctuation to the actuator.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1101-1106
• /
• 2004

This study presents the reconstruction of sound field radiated from an automotive engine using equivalent sources. Basic concept of the method presented is to replace the engine noise source with elementary sources of multipoles, e.g., monopoles and dipoles. The so-called Helmholtz equation least-squares (HELS) method can reconstruct the sound radiation fields from spherical geometries in a series expansion of spherical Hankel functions and spherical harmonics. In this paper, multi-Point, multipole equivalent sources are employed to reconstruct the sound field radiated from an automotive engine with a fixed rotation speed. To ensure and improve the accuracy of reconstruction, the spatial filters of multipole coefficients and wave-vectors are adopted for suppressing the adverse effect of high-order multipoles. Optimal filter shapes are designed with regularization parameters minimizing the generalized cross validation (GCV) function between actual and reproduced model. After regeneration of field pressures using the proposed method as many as necessary, the vibro-acoustic field of an engine could be reconstructed by using the BEM-based near-field acoustic holography (NAH) technique in a cost-effective manner.

• Mycobiology
• /
• 제47권3호
• /
• pp.319-328
• /
• 2019

Cytospora is a genus including important phytopathogens causing severe dieback and canker diseases distributed worldwide with a wide host range. However, identification of Cytospora species is difficult since the currently available DNA sequence data are insufficient. Aside the limited availability of ex-type sequence data, most of the genetic work is only based on the ITS region DNA marker which lacks the resolution to delineate to the species level in Cytospora. In this study, three fresh strains were isolated from the symptomatic branches of Elaeagnus angustifolia in Xinjiang Uygur Autonomous Region, China. Morphological observation and multi-locus phylogenetic analyses (ITS, LSU, ACT and RPB2) support these specimens are best accommodated as a distinct novel species of Cytospora. Cytospora elaeagnicola sp. nov. is introduced, having discoid, nearly flat, pycnidial conidiomata with hyaline, allantoid conidia, and differs from its relatives genetically and by host association.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.16-23
• /
• 2012

연소시험을 통한 성공/실패 사례가 있는 FASTRAC 연소기에 대해, 효용성이 검증된 3차원 선형 음향해석을 수행하여 음향공의 물성치 변화에 따른 감쇠 특성을 파악하였다. 음향공의 동조주파수와 감쇠능력을 정량화하기 위해 acoustic impedance 개념을 도입하였다. 기하학적 형상이 주어진 상태에서, 음향공 내부의 음속 변화에 따라 최적의 동조가 가능한 음속을 파악하였다. 최적의 동조가 이루어지기 위한 음향공 내부의 음속 예측 방법을 제시하였다. 이를 통하여 여러 기하학적 형상을 가지는 음향공에 대하여 적용하여 감쇠능력을 정량화함으로써 연소안정성의 확보 여부에 대한 검토가 가능할 것이며, 안정성이 확보되지 못한 경우에 대해서는 그 이유를 명확하게 규명할 수 있을 것이다.

• Nuclear Engineering and Technology
• /
• 제53권10호
• /
• pp.3133-3150
• /
• 2021

This work deals with the validation of a high-fidelity multiphysics system coupling the Serpent 2 Monte Carlo neutron transport code with SUBCHANFLOW, a subchannel thermalhydraulics code, and TRANSURANUS, a fuel-performance analysis code. The results for a full-core pin-by-pin burnup calculation for the ninth operating cycle of the Temelín II VVER-1000 plant, which starts from a fresh core, are presented and assessed using experimental data. A good agreement is found comparing the critical boron concentration and a set of pin-level neutron flux profiles against measurements. In addition, the calculated axial and radial power distributions match closely the values reported by the core monitoring system. To demonstrate the modeling capabilities of the three-code coupling, pin-level neutronic, thermalhydraulic and thermomechanic results are shown as well. These studies are encompassed in the final phase of the EU Horizon 2020 McSAFE project, during which the Serpent-SUBCHANFLOW-TRANSURANUS system was developed.

• 한국추진공학회지
• /
• 제23권2호
• /
• pp.38-45
• /
• 2019

본 연구에서는 항공용 가스터빈의 연소실에서의 연소불안정 해석을 위한 고유값 도출을 목적으로 하는 1D 네트워크 모델을 개발하였다. 모델은 면적 변화가 있는 음향 네트워크 요소들 사이의 각종 지배 방정식을 통하여 개발되었고, 이를 이용하여 현재 개발 중인 복잡한 유로 형상을 갖는 실제 항공용 가스터빈 연소기에서의 음향장 해석에 적용되었다. 본 모델을 통하여 도출된 음향장 해석 결과는 3차원 유한요소해석 기반의 헬름홀츠 솔버의 계산 결과와 비교하였다.

• Advances in nano research
• /
• 제10권3호
• /
• pp.271-280
• /
• 2021

The present work deals with an investigation on longitudinal wave propagation in nanobeams made of graphene sheets, for the first time. The nanobeam is modelled via a higher-order shear deformation theory accounts for both higher-order and thickness stretching terms. The general nonlocal strain gradient theory including nonlocality and strain gradient characteristics of size-dependency in order is used to examine the small-scale effects. This model has three-small scale coefficients in which two of them are for nonlocality and one of them applied for gradient effects. Hamilton supposition is applied to obtain the governing motion equation which is solved using a harmonic solution procedure. It is indicated that the longitudinal wave characteristics of the nanobeams are significantly influenced by the nonlocal parameters and strain gradient parameter. It is shown that higher nonlocal parameter is more efficient than lower nonlocal parameter to change longitudinal phase velocities, while the strain gradient parameter is the determining factor for their efficiency on the results.

• Wind and Structures
• /
• 제37권3호
• /
• pp.191-209
• /
• 2023

This work investigates the subcritical free-shear prism wake at Re=22,000 by the Koopman analysis using the Dynamic Mode Decomposition (DMD) algorithm. The Koopman model linearized nonlinearities in the stochastic, homogeneous anisotropic turbulent wake, generating temporally orthogonal eigen tuples that carry meaningful, coherent structures. Phenomenological analysis of dominant modes revealed their physical interpretations: Mode 1 renders the mean-field dynamics, Modes 2 describes the roll-up of the Strouhal vortex, Mode 3 describes the Bloor-Gerrard vortex resulting from the Kelvin-Helmholtz instability inside shear layers, its superposition onto the Strouhal vortex, and the concurrent flow entrainment, Modes 6 and 10 describe the low-frequency shedding of turbulent separation bubbles (TSBs) and turbulence production, respectively, which contribute to the beating phenomenon in the lift time history and the flapping motion of shear layers, Modes 4, 5, 7, 8, and 9 are the relatively trivial harmonic excitations. This work demonstrates the Koopman analysis' ability to provide insights into free-shear flows. Its success in subcritical turbulence also serves as an excellent reference for applications in other nonlinear, stochastic systems.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.126-135
• /
• 1995

An exhaust muffler is one of the simple and effective means to meet the demand for a quiet vehicle, and it deserves a close attention to effectively reduce the engine noise. The transfer function technique is one of the tools that have been used to analyze the noise characteristics of the exhaust muffler. In this paper we obtained a transfer function using the forward-going and backward-going components of sound pressure in the exhaust muffler, which is compatible wiht lattice filter algorithm. This form of transfer function is obtained for the basic elements of a muffler, such as uniform tube, open termin- ation, closed termination, anechoic termination, expansion, contraction, extended-tube resonator, hole, Helmholtz resonator, and concentric hole-cavity resonator. The results are combined to produce the transfer function of various types of mufflers. With this transfer function we calculate the transmission and insertion losses of mufflers, and examined the effects of various design parameters. Comparisons were made between the calculation and experimental results, which showed a good agreement, and we conclude that the transfer function of lattice form can be used to analyze the noise characteristics of the exhaust mufflers.