• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.19-28
• /
• 2009

Some wood anatomical characteristics of seven chestnut cultivars (Tanzawa, Ibuki, Arima, Ginyose, Tsukuba, Riheiguri, and Mansung) grown in Korea were examined in this study. We investigated the radial variation of wood components such as diameter and number of earlywood vessel element and ray density in cross section and number and height of ray in tangential section. Discs were taken from the stem of seven chestnut cultivars at breath height and cut into the radial strip. Cross, radial, and tangential sections, 10 to $20{\mu}m$ thick, were sliced with a sliding microtome. These sections were stained, dehydrated, and mounted with Canada balsam according to common procedure. Measurement and observation were performed with a light microscopy. In all chestnut cultivars, radial and tangential diameter of vessel element increased but number of vessel element per $mm^2$ decreased with increasing tree age. Ray spacing (per mm) in cross section from pith to bark showed no significant variation, while number of ray per $mm^2$ increased but ray height decreased with the increase of tree age. Conclusively, the results obtained in present study were thought to be some valuable information for separating juvenile and adult wood as well as identifying chestnut cultivars.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.11
• /
• pp.2260-2266
• /
• 2009

In this paper, the problem of electromagnetic coupling between a slit fed by a flanged parallel-plate waveguide (FPPW) and a nearby conducting strip parallel to the slit is studied as a simplified problem for a near-field scanning microscopy (NSM). The characteristics of the FPPW are investigated from the results for the variations of the equivalent slit admittance, the reactive powers near the slit inside and outside the FPPW, the magnitude and phase of the voltage reflection coefficient of the TEM wave. The performance of the proposed apparatus as an NSM is tested by examining the effects of various geometrical parameters such as guide height, slit width, strip width, distance between slit and strip, and the ratio of slit width to guide height on the magnitude and phase of the voltage reflection coefficient of the TEM wave. From the results for the voltage reflection coefficient against the strip offset from the slit, it is found that a slit in the FPPW with smaller guide height gives higher scanning resolution and the phase variation is more sensitive than the magnitude variation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.2
• /
• pp.150-158
• /
• 2011

Present study aims to investigate the influence of relative breakwater width W/L (W=width of breakwater, L=wavelength), wave steepness $H_i/gT^2$ (Hi=incident wave height, T=wave period) and relative wave height d/W (d=water depth) on forces in the moorings of horizontal interlaced multi-layered moored floating pipe breakwater (HIMMFPB) model. Studies were conducted on scaled down physical models having three layers of Poly Vinyl Chloride (PVC) pipes, wave steepness $H_i/gT^2$ varying from 0.063 to 0.849, relative width W/L varying from 0.4 to 2.65 and relative spacing S/D=2 (S=horizontal centre-to-centre spacing of pipes, D=diameter of pipes). Peak mooring forces were also measured and data collected is analyzed by plotting non-dimensional graphs depicting variation of $f_s/{\gamma}W^2$ ($f_s$=Sea side Mooring force, ${\gamma}$=specific weight of water) & $f_l/{\gamma}W^2$ ($f_l$=Lee side Mooring force) with $H_i/gT^2$ for d/W varying from 0.082 to 0.276 and also variation of $f_s/{\gamma}W^2$ and $f_l/{\gamma}W^2$ with W/L for $H_i$/d varying from 0.06 to 0.400.

• Architectural research
• /
• v.21 no.4
• /
• pp.91-98
• /
• 2019

In modern times, numerous cities are competing to create the unique skyline adjacent to the water. Tall buildings located across the river have a great contribution to the skyline of a riverfront city and can be a precious asset for the city. Moreover, in several cities, tall buildings and their impact on the urban skyline are a matter that should be considered and regulated in urban design. Therefore, as a prominent element in a larger visual setting of the city, tall buildings should improve the visual quality of the skyline rather than diminish that quality. This research attempts to provide an objective method to analyze the visual quality of the skyline made by a group of tall buildings through their feature of heights and spatial arrangement from riverfront views. The analysis is determined by the design variables of building heights variation, heights transition, density, and spacing of a group of tall buildings. A comparative case study of tall buildings in Yeouido and Lujiazui was conducted to prove the effectiveness of the analysis. The proposed method can be used in a simple way in the quantitative approach to quantify the visual quality of the skyline. In conclusion, Yeuido's skyline is not quite interesting from the riverfront view in terms of height variation and continuity of the skyline view because they are dispersed. Conversely, Lujiazui's skyline from the riverfront vantage points has a good quality in all aspects of the feature of height and spatial arrangements of tall buildings cluster. These factors can be used for the urban designer on how proposed tall buildings within the cluster should appropriately respond to adding image on the skyline.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.2
• /
• pp.126-132
• /
• 2010

An approach to calculating expected damage of breakwater assisted by artificial neural network was developed. Wave height in front of a breakwater was predicted by a trained artificial neural network with inputs of wave height in deep ocean and tidal level. Prediction results by the neural network can be comparable to that by professional numerical model for wave transformation. Using the wave prediction neural network, it was very easy and fast to obtain a number of significant waves at breakwater and finally analysis time for expected damage can be shortened. In addition, the effect of considering tidal level in the calculation of expected damage was revealed by comparing the expected damages with and without tidal variation. Therefore, it was pointed out that tidal variation should be considered to improve prediction accuracy.

• Geomechanics and Engineering
• /
• v.23 no.1
• /
• pp.85-92
• /
• 2020

This study adopted soil test and laboratory physical model experiments to simulate the tailings impoundment accumulation process according to the principle of similarity. Relying on the practical engineering, it analyzed the tailings deposition characteristics on dry beach surface during the damming process, as well as the variation rules of dam saturation line. Results suggested that, the tailings particles gradually became finer along the dry beach surface to inside the impoundment. The particle size suddenly changed at the junction between the deposited beach and the water surface, which displayed an obvious coarsening phenomenon. Besides, the deposited beach exhibited the vertical feature of coarse upward and fine downward on the whole. Additionally, in the physical model, the saturation line elevated with the increase in dam height, and its amplitude was relatively obvious within the range of 1.0-4.5 m away from the initial dam. Under flood condition, the saturation line height was higher than that under normal condition on the whole, with the maximum height difference of 4 cm. This study could provide an important theoretical basis for further studies on dam failure experiments and the evolution rules of leaked tailings flow.

• Journal of the Korean Home Economics Association
• /
• v.30 no.3
• /
• pp.15-32
• /
• 1992

The purpose of this study was to detect the effect of the lower body type on the shape of flare skirts. The subjects for the wearing test were 50 female students, who were controlled in their hip and waist shapes. The skirts used for wearing test were six types(three flar angles $\times$ two fabric types). The effect of lower body type on the shape of flare skirts was determind by the hemline trace method and the silhouette photography. The data were then analyzed by the repeated measures of analysis of variance and the SNK multiple range test. The results obtained from this study were as follows : 1) When a flare skirt made with larger flare angle and better drapable fabric was worn, the numeric of the nodes increased as the drop value(hip - waist) increased. When a flare skirt made with smaller flare angle was worn, the width of horizontal sectio of hemline increased as the drop value increased. The hemline uneveness decreased on the sides and back as the drop value increased. When a flare skirt made with worse drapable fabric was worn, the sides angle of the flarskirt increased as the drop value increased. 2) When a flare skirt made with larger flare angle was worn, the numeric of nodes increased as the ratio of dropped hip increased. The wave-height increased and the back variation ratio of wave-height was higher than the front variation ratio of wave-height as the ratio of dropped hip increased. The hemiline uneveness decreased on the back as the ratio of dropped hip increased. When a flare skirt made with larger flare angle was worn, the sides angle of the flare skirt increased as the ratio of dropped hip increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.1 s.232
• /
• pp.46-54
• /
• 2005

Film cooling characteristics has been examined numerically for the height variation of a stepped slot exit. In this study, the upstream wall height of the stepped slot exit varies from -2d (d = slot width) to 3d, blowing ratio ranges from 0.5 to 3, and injection angles are $15^{\circ},\;30^{\circ},\;and\;45^{\circ}$. The results showed that film cooling performance was mainly subjected to the magnitude of recirculation region near the downstream-side slot exit as well as the magnitude and the distribution region of turbulent kinetic energy due to the local velocity and momentum differences between the coolant and the main flow near the slot exit. The up-1d type slot at higher blowing ratios over 2 and the flat type slot at lower blowing ratios below 1 have the best film cooling performances, in case of the injection angles of $30^{\circ},\;and\;45^{\circ}$, respectively. Compared with the other injection angles, in case of the injection angles of $15^{\circ}$, the best film cooling performances was shown in even a higher upstream wall (up-3d) at higher blowing ratio like 3 by the gradual reduction of the coolant velocity which minimizes the local velocity differences between the coolant and the main flow near the slot exit.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5B
• /
• pp.463-472
• /
• 2009

The aim of this study is to examine the effect of beach curvature on wave fields in coastal area with Submerged Breakwaters using the 3D numerical model that is able to simulate directly interaction of WAve Structure Sandy beach (LES-WASS-3D). At first, the adopted model was validated through the comparison with an existing experimental data and showed fairly nice agreement. And then, the numerical simulations have been performed to investigate the effect of according to the variation of beach curvature. Based on the numerical results, the wave height, mean surface elevation, mean flow around submerged breakwaters and longshore distributions of run-up height have been discussed in relation to the variation of beach curvature.

• Journal of the Korea Society of Computer and Information
• /
• v.11 no.6 s.44
• /
• pp.279-287
• /
• 2006

This paper proposes a method to detect fall action by using stereo images to recognize emergency situation. It uses 3D information to extract the visual information for learning and testing. It uses HMM(Hidden Markov Model) as a recognition algorithm. The proposed system extracts background images from two camera images. It extracts a moving object from input video sequence by using the difference between input image and background image. After that, it finds the bounding rectangle of the moving object and extracts 3D information by using calibration data of the two cameras. We experimented to the recognition rate of fall action with the variation of rectangle width and height and that of 3D location of the rectangle center point. Experimental results show that the variation of 3D location of the center point achieves the higher recognition rate than the variation of width and height.