• Journal of Power Electronics
• /
• 제6권2호
• /
• pp.178-185
• /
• 2006

Recently, the demand for the development of high quality and high-speed laser printers and efficient power utilization has required. Among complicated electro-mechanic devices in laser printers, the toner-fusing unit consumes above 90[%] of all electrical energy needed for printing devices. Therefore, the development of a more effective energy-saving toner fusing process becomes a significant task in great demand. Generally, there are several ways to implement a fusing unit. Among them this paper presents a new induction heating method. The proposed induction heating method enables the increase of coupling coefficient between heating coil and heat roller which also increases total energy transfer efficiency. Therefore, the proposed IH (Induction Heating) inverter system provides very fast W.U.T. (Warm UP Time) as well as higher efficiency. Through experimental results, the proposed control system is verified.

• 한국도로학회논문집
• /
• 제18권2호
• /
• pp.73-82
• /
• 2016

PURPOSES: The national highways and expressways in Korea constitute a total length of 17,951 km. Of this total length of pavement, the asphalt pavement has significantly deteriorated, having been in service for over 10 years. Currently, hot in-place recycling (HIR) is used as the rehabilitation method for the distressed asphalt pavement. The deteriorated pavement becomes over-heated, however, owing to uncontrolled heating capacity during the pre-heating process of HIR in the field. METHODS: In order to determine the appropriate heating method and capacity of the pre-heater at the HIR process, the heating temperature of asphalt pavement is numerically simulated with the finite element software ABAQUS. Furthermore, the heating transfer effects are simulated in order to determine the inner temperature as a function of the heating system (IR and wire). This temperature is ascertained at $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$, $600^{\circ}C$, $700^{\circ}C$, and $800^{\circ}C$ from a slab asphalt specimen prepared in the laboratory. The inner temperature of this specimen is measured at the surface and five different depths (1 cm, 2 cm, 3 cm, 4 cm, and 5 cm) by using a data logger. RESULTS: The numerical simulation results of the asphalt pavement heating temperature indicate that this temperature is extremely sensitive to increases in the heating temperature. Moreover, after 10 min of heating, the pavement temperature is 36%~38% and 8%~10% of the target temperature at depths of 25 mm and 50 mm, respectively, from the surface. Therefore, in order to achieve the target temperature at a depth of 50 mm in the slab asphalt specimen, greater heating is required of the IR system compared to that of the gas. CONCLUSIONS : Numerical simulation, via the finite element method, can be readily used to analyze the appropriate heating method and theoretical basis of the HIR method. The IR system would provide the best heating method and capacity of HIR heating processes in the field.

• 한국식품조리과학회지
• /
• 제30권1호
• /
• pp.51-63
• /
• 2014

A microbiological quality evaluation on cooked food, food materials and cooking equipment was conducted in 14 school food services in Changwon area, South Korea for Ojingeochaesomoochim (vegetable salad with blanched squid) which went through cooking process after heating treatment. Only 5 schools out of the 14 (35.7%) observed the sanitization criteria of the Korean School Meals Sanitization Management for raw vegetables (concentration of chlorine solution: 100ppm, immersion time of sanitizing: 5 min). The acceptance rates regarding the microbial standards for Korean school meals showed improvement before and after of sanitization: for onions 57.1% vs 71.4%; cucumber 42.9% vs. 78.6%. However, garlic showed adverse sanitizing effect as the acceptance rate went down from 42.9% to 35.7%. Blanched squid and red pepper paste was acceptable in all 14 schools (100%), while squid seasoned with red pepper powder was acceptable in only 42.9% of the schools. Microbial results for knives, cutting boards, mixing bowls were satisfactory, however 35.7% of sanitary gloves that were put on right before the seasoning showed poor sanitization, and this indicated high probability of cross-contamination from the gloves. We calculated that 57.1% of the cooked foods were in accordance with the microbial standards for Korean school meals. Therefore, it is strongly recommended to have verification process, especially on the effectiveness of sanitization of raw vegetables, in cooking foods through cooking process after heating treatment in HACCP system of school food service.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.942-945
• /
• 2005

Micron-sized metal wires are widely used in industries such as filtration, catalyst and composite materials, etc. In the wire drawing process, the die that is used conventionally is an effective and, at the same time, sensitive component. However, a typical array of the dies has caused many problems in the wire drawing process, e.g., large frictional force on the interface between wire and the resulting high heat generation, precise adjustment of the dies, extended cooling system, die abrasion, etc.. Because of these problems, there have been many works that are aiming at improving the efficiency of wire drawing process by analyzing the die geometry and by applying advanced die material to prolong the die life or even at developing a dieless wire drawing system. This paper is dealing with developing a new wire drawing system that is applicable to reduce the wire drawing steps with high draw ratio. The new wire drawing system does not use the dies, but use the self-induced heater that works on the basis of the resonant phenomenon of wire material. The electromagnetic wave is the heating source. The results of the study on the diameter reduction and microwave flow analysis show that the heating effectiveness of the wire is influenced by the energy distribution in the microwave propagation chamber. We can obtain diameter-reduced wires by using microwave in the dieless drawing process. Microwave as a heating source is capable of producing wires without applying dies in wire drawing process.

• 대한기계학회논문집A
• /
• 제38권7호
• /
• pp.809-815
• /
• 2014

최근들어 원자력 발전소에 유도 가열 공정으로 굽힌 배관을 적용하려는 동향이 있다. 이러한 유도 가열 굽힘 공정 동안의 열-기계적 메커니즘에 의해 잔류응력이 발생할 수 있다. 잔류응력은 균열 발생과 성장에 중요한 영향을 미치는 균열 구동력들 중의 하나이다. 그러나, 기존 연구들은 두께 변화, 타원도와 같은 기하학적 형상 변이에 집중하고 있는 반면 공정 변수가 잔류응력에 미치는 영향과 관련된 연구는 찾아보기 힘들다. 본 연구에서는 316 오스테나이트 스테인리스 강으로 제작된 유도 가열 굽힘 배관의 잔류응력 분포에 미치는 공정 변수의 영향을 유한요소 변수 해석을 통해 고찰하였다. 고찰결과, 굽힘 모멘트와 굽힘 각도는 잔류응력에 미치는 영향이 미미한 반면 유도 가열률과 이송 속도는 잔류응력에 상당한 영향을 미침을 확인하였다.

• 유기물자원화
• /
• 제23권4호
• /
• pp.63-73
• /
• 2015

우분을 전처리하는 방법을 적용함에 따라 열량값이 변화하는 정도를 측정하는 실험을 수행하였다. 전처리 방법으로는 퇴비화 방법, 건식 혐기소화 방법, 물리적 압착 방법 등 3가지 방법을 적용하였다. 실험결과, 우분을 퇴비화하거나 혐기소화를 실시하는 경우에 열량값이 감소하는 것으로 나타났다. 퇴비화 처리를 적용하였을 경우 완숙퇴비의 열량값은 퇴비화 초기 원료에 비해 약 5% 정도 감소하였다. 우분을 건식 혐기소화한 뒤 수거된 혐기소화 잔재물의 열량값은 혐기소화 원료로 사용한 우분에 비해 약 25.7% 정도가 감소하였다. 우분을 압착하는 방법에 의해 수분을 감소시킨 경우에는 압착을 거친 우분의 열량값이 압착 전의 원료 우분에 비해 약간 높아지는 결과를 보였다. 또한 총 고형물 중에서 휘발성 고형물이 차지하는 비율도 높아진 것으로 나타났다. 반면에 우분을 압착하는 과정에서 발생된 침출수의 열량값과 총 고형물 중의 휘발성 고형물의 비율은 원료로 사용한 우분에 비해 더 낮아졌다.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.1-10
• /
• 2020

This study deals with the fabrication and thermal characterization of planar heating elements attached to the backside of the reflector used in the electrodeless lamp of a freezer. We tried to solve the problem of the local heat generation of the linear heating element that occurs about 50℃. The homogeneous dispersion and manufacturing excellence of the planar heating element produced were confirmed through SEM and EDS. In addition, the test specimens was prepared according to the change in the ratio of carbon fiber to the basis weight of the planar heating element, and a sample having a basis weight of 50g/㎡ having a content ratio of carbon fiber of 70% was selected. That sample showed low surface resistance of 4.3Ω/sq and high temperature of about 81℃ at 6V. Durability was confirmed by performing repeated bending evaluation of 3000 cycles for the sample. Large area test specimens were prepared to be applied to the actual reflector, insulated by EVA film and analyzed for their thermal characteristics. From 13V application, the temperature of the linear heating element was higher than 50℃ and the average temperature of 68℃ was maximum at 18V.

• 항공우주시스템공학회지
• /
• 제15권5호
• /
• pp.1-7
• /
• 2021

Ti-6Al-4V 티타늄 합금은 무게 대비 우수한 강도와 고온 강도 특성 때문에 수요가 증가하고 있지만 상온에서 낮은 성형성 때문에 고온으로 성형을 해야 한다. 현재 진행된 고온 성형 연구는 하부 금형을 가열하여 시편을 가열하는 방식이기 때문에 제약이 많다. 기존 고온 성형 방식과 다르게 제품을 국부적으로 가열할 수 있는 고주파 유도가열을 적용한다면 가공의 효율성을 높일 수 있을 것으로 예상된다. 또한 공정 기술 개발 시 신뢰도 높은 해석 기법으로 미리 공정을 시뮬레이션한다면 시간과 비용을 절약할 수 있다. 본 논문에서는 고주파 유도가열을 이용하여 Ti-6Al-4V 합금을 가열하였고 실험 결과와 전자기-열전달 연동 해석 결과를 비교하여 해석의 신뢰도를 판단하였다.

• 한국염색가공학회지
• /
• 제20권3호
• /
• pp.25-30
• /
• 2008

In order to examine the availability of a heating process for persimmon dyeing, the cotton fabrics treated with various concentrations of persimmon extracts were heated at various temperatures and times. The raw and fermented persimmon extracts were used for the coloration. For both extracts, the color strength of fabrics was. increased with the increase of coloration temperature, time, and concentration of the extracts. Considering the practical aspects. and color strength, the temperature around $200^{\curc}C$ and the time longer than 60 minutes can be determined as the. optimum coloration conditions of persimmon extracts onto cotton fabrics. However, somewhat loss of strength by the hearing process seems to be inevitable. The color fastness to washing was excellent for both color change and staining showing a rating of 5.

• 산업기술연구
• /
• 제24권A호
• /
• pp.17-22
• /
• 2004

In the study, we have developed a straightening system for 304 micro wires that are normally used in the medical and semi-conductor fields. To apply heat to the micro wires, we introduced the direct wire heating method which generates the thermal energy by the electrical resistance of the wire itself. To avoid the deterioration of the wire surface by the environment, such as the oxidation or the hydration, the $N_2$ gas was filled in the glass pipe in which the straightening process was being performed. A precision tension meter was also attached to control the tension of the wire during the heating and straightening process. In order to control the straightening process, several experimental investigations with varying the tension, the feeding velocity and the temperature (current) was carried out. As a result of experiments, we obtained the optimal processing conditions satisfying the straightness requirement of the micro wires.