• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.150-153
• /
• 1999

The electrical and physical characteristics of MgO and Pt thin-films on Si wafers deposited by r.f magnetron sputtering, were analyzed with annealing condition(100$0^{\circ}C$, 120 min) by four point probe, SEM and XRD. Until annealing temperature of 100$0^{\circ}C$, MgO had the properties of improving Pt adhesion to SiO$_2$ and insulation without chemical reaction to Pt thin-films and the resistivity of Pt thin-films was improved. The thermal characteristics of Pt micro-heater were analyed with Pt-RTD integrated on the same substrate, In the analysis of properties of Pt-RTD, TCR value had 3927 ppm/$^{\circ}C$ and liner in the temperature range of 25~40$0^{\circ}C$ temperature of Pt micro-heater had up to 40$0^{\circ}C$ with 1.5 watts of the heating power.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.8 no.1
• /
• pp.29-39
• /
• 2000

A series of tests were performed to verify the transient characteristics of heat pump in heating and cooling mode when operating speed was varied over the 30 to 102Hz. One of the major issues that has not been addressed so far is transient characteristics during speed modulation. The model for cycle simulation has been developed to predict the cycle performance under conditions of decreasing drive frequency and the results of the theoretical study were compared with the results of the experimental study. The simulated results were in good agreement with the experimental result within 10%. The transient cycle migration of the liquid state refrigerant causes significant dynamic change in system. Thus, the migration of refrigerant was the most important factor whenever do experimental results analysis or develop simulation model.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.9-16
• /
• 2004

A study of the propeny and performance effect of Indolene - Methanol Plus High Alcolhols (MPHA) has been completed. This study invested the measurement of fuel properties and performance parameters. The fuel properties investigated are distillation characteristics, heating valuer flash point, specific gravity and water tolerance. The performance parameters measured are minimum advance for best torque (MBT) spark timing, power output. The alcohol concentration was varied from 0 to 100 percent by volume in clear Indolene. The measurement of fuel properties indicated that, in general, Indolene - MPHA blends have higher water tolerance, similar specific gravity, similar flash point and different distillation characteristics compared to Indolene - Methanol blends. The performance parameters were measured using a single cylinder spark ignition engine at different compression ratios. The results of the performance measurements indicated that Indolene - MPHA blends have a higher MBT spark advance, similar power output.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.368-371
• /
• 2003

The humidity sensors with a stable characteristics and gas sensors operating at room temperature have been fabricated, and a multi-functional sensor system which has gas sensor, humidity sensor, temperature sensor and control circuit has been applied to the microwave oven system. For a suitable cooking state, the humidity sensors was more applicable to heating and defrosting condition than gas sensors, however, the dynamic characteristics of gas sensors were obtained in the easy burning food such as pop corn.

• The Korean Journal of Food And Nutrition
• /
• v.7 no.4
• /
• pp.353-360
• /
• 1994

Effect of pH, calcium, sucrose, heating and mixing ratio of soy and cow milk was studied on the viscosity and the sensory characteristics of cow-soy milk. The viscosity of soymilk was significantly affected by pH with showing maximum at 6.0 and the pH effect was decreased as the ratio of cow talk increased. A addition of sucrose or calcium affected little on the viscosity and a negative linear relationship was found be tween viscosity and an increase in cow milk ratio. Sensory characteristics of grassy and beany odor and taste of soymilk were rapidly decreased and nutty flavor and total acceptability were increased during initial 30 min of boiling. A further increase in boiling affected little on tastes and odors of soymilk. The beany odor and taste linearly decreased and milk flavor Increased as the ratio of cow milk increased. The total acceptability of 50 : 50 was found to be maximum for cow and soy mixed milks.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.3
• /
• pp.277-283
• /
• 2000

The heat transfer characteristics for air jet vertically impinging on a flat plate which had a set of hybrid rod were investigated experimentally. The rod had a cross section made with a half of circular cross section and that of rectangular and was installed in front of the plate. The heating surface was given constant heat flux value of 1020 W/$m^2^{\circ]C$ and the problem parameters investigated were jet Reynolds number, nozzle-to-plate spacing and the rod size. The local and local average Nusselt number characteristics were found to be dependent on the rod size because the flow was disturbed by installing the rod. Higher convective heat transfer rate occurred in the whole plate as well as in the stagnation region.

• Journal of ILASS-Korea
• /
• v.15 no.1
• /
• pp.31-37
• /
• 2010

The aim of this work is to investigate the spray and combustion characteristics of dimethyl-ether (DME) at various injection conditions. The spray characteristics such as spray tip penetration and spray cone angle were experimentally studied from the spray images which obtained from the spray visualization system. Combustion and emissions characteristics were numerically investigated by using KIVA-3V code coupled with Chemkin chemistry solver. From these results, it revealed that DME spray had a shorter spray tip penetration and wider spray cone angle than that of diesel spray due to the low density, low surface tension, and fast evaporation characteristics. At the constant heating value condition, DME fuel showed higher peak combustion pressure and earlier ignition timing, because of high cetane number and superior evaporation characteristics. In addition, the combustion of DME exhausted more $NO_x$ emission and lower HC emission due to the active combustion reaction in the combustion chamber. The result shows that DME had a little soot emission due to its molecular structure characteristics with no direct connection between carbons.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1996.10b
• /
• pp.91-97
• /
• 1996

Bench Scale급 가스화기를 이용하여 중국 대동탄에 대하여 O2/coal 비, 가스화기 운전 압력에 따른 가스화 특성을 조사하였다. 가스화기를 가압하는 방법으로 메탄과 산소의 버너를 이용하여 운전 압력까지 단시간 내에 가압하는 방법을 정립하였다. 가스화기 압력은 상압으로부터 10기압까지 실험을 실시하였으며, 10기압, 반응온도 1350-140$0^{\circ}C$, O2/coal 비(as-fed 기준) 0.9의 운전조건에서 탄소전환률 90%이상, 냉가스효율 60%, 그리고 heating value 1800 Kcal/N㎥ 정도의 생성가스 특성을 얻을 수 있었다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1998.05a
• /
• pp.173-176
• /
• 1998

FCC (Fluid Catalystic Cracking) 장치는 중질유의 원유와 잔사유로부터 가솔린과 heating oil. 디젤연료 제조 등에 사용되고 있다. 이 장치는 50년 동안 fine-powder 유동화에 중요하게 응용되고 있으며, 현재 세계적으로 약 350여 개의 장치가 조업되고 있다. FCC 장치에서 미세한 분해촉매는 촉매에 의한 중질유의 분해가 일어나는 상승관 (riser)과 촉매의 재생이 일어나는 재생반응기(regenerator) 사이에서 높은 속도로 순환되고 있다. (중략)

• Proceedings of the SAREK Conference
• /
• 2006.11a
• /
• pp.59-59
• /
• 2006