• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.19-22
• /
• 2007

In this study, we investigated operating characteristics of natural gas fuel processor for polymer electrolyte membrane fuel cells (PEMFCs). The fuel processor consists of a natural gas reformer, a water-gas shift reactor, a heat-exchanger and a burner, in which the overall integrated volume is exactly(exceptionally) small, namely, about 10L except outer insulation. The producted hydrogen is $1Nm^3/hr$ and the maximum thermal efficiency is ${\sim}76%$(low heating value) at full operating load. A compact and highly efficient $1Nm^3/hr$ class natural gas fuel processor was developed at UNISON is an advantage for application in residential PEMFCs co-generation systems.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.35-39
• /
• 2003

Laser welding has good characteristics such as high density energy, high speed and short heating time, as compared with conventional arc welding. The joint of laser welding also has good mechanical characteristics in general. However, relevant research is not sufficient to understand laser welding in the view point of mechanics until a recent date. In this paper, numerical simulation has been conducted to analyze distribution of welding residual stresses. Welding residual stresses of specimen have been measured by using sectioning method to compare the results between simulation and experiment.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.621-624
• /
• 2002

In this study, outgassing characteristics of MgO films, and the plasma cleaning effects of the deposited MgO films by atmospheric pressure plasma on outgassing rate were compared. The MgO layer was heated up to 350 $^{\circ}C$ and the outgassing characteristics were observed for the heated conditions. As the main impurity species $H_2,\;H_2O,\;N_2,\;CO_2,\;and\;H_2O$ were released from this panel. Impurity species of plasma treatment panel were lower than non-treated panels for the heating temperature

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.895-900
• /
• 1997

A Quench in cable-in-conduit (CIC) conductors is often initiated by a disturbance such as strand motion that generates a highly localized normal zone in a strand or a few strands of the CIC conductors. The localized normal zone causes current and heat transfer between a disturbed strand and neighboring strands. Electrical and thermal contact characteristics between strands thus have an effect on the transient stability of the CIC conductors. In this paper the effect of contact characteristics between strands on the CIC conductor stability is presented based on the measured heat transfer characteristics of supercritical helium (SHe) for the local heating. The quench and recovery processes of the strands for the abrupt and highly localized disturbance are analyzed at the boundary between quench and recovery.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.387-389
• /
• 2009

PV module is manufactured by several steps such as cell sort, tabbing & string, lay-up, lamination processes. In oder to manufacture PV module, solar cell must be placed in high temperature. Soldering Process in high temperature is important because it directly influences electric output performance changes of solar cell in solar cell module. We consider applying momentary high temperature, while soldering solar cell, and expect change electric characteristics of PV module. In this paper, we measure electric output characteristics of solar cells after those are applied with high temperature changes for two seconds. From these results, we confirm with application of high temperature, $I_{sc}$ increase and $V_{oc}$ slightly decreases.

• Journal of the East Asian Society of Dietary Life
• /
• v.20 no.3
• /
• pp.423-432
• /
• 2010

In order to streamline bread making process that is time-consuming in regard to the characteristics of process, this study focused on microwave irradiation to dough and raising its temperature to monitor potential variations of dough properties and bread quality, and also examined optimum irradiation time to deduce effective ways for streamlining bread making process. According to analyze dough properties depending on microwave irradiation time, it was found that microwave heat (MWH) 2 showed the highest specific volume and oven spring of all and the lowest hardness (i.e. the highest softness). Moreover, MWH 2 scored the highest points in overall preference under sensory characteristics. As a result, it found that 80-second heating of 700 g bread dough, when exposed to microwave irradiation, contributed to the highest quality of bread.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.87-92
• /
• 1998

Major characteristics of shrinking and rehydration of Korean tea-leaves were investigated in the hot-air drying equipment. Experiments were performed with various drying temperature, plucking time, heating method and rolling condition. The values of shrinking raito and rate were the highest at 7$0^{\circ}C$ in the range of 3$0^{\circ}C$ to 9$0^{\circ}C$. The 1st tea-leaves and showed higher values. Shrinking ratio was 16.62 and 19.62% for leaves and stems; shrinking rate was found 0.083 and 0.091cm/hr.cm, respectively. The rehydration characteristics of tea-leaves at the drying temperature of 3$0^{\circ}C$ were fairly satisfactory. The 2nd tea-leaves showed higher value than others, while the natural tea-leaves were lower. Average rehydration ratio and rehydration rate constant were 85.7% and 0.063/min for leaves; 80.1% and 0.032/min for stems, respectively.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.645-654
• /
• 1988

The microstructure and electrical characteristics of ZnO-Bi2O3 ceramics containing 5mol% Bi2O3 have been studied in relation to sintering temperature and mode. The distribution and thickness of Bi2O3 intergranular layer was varied with sintering temperature and mode. Intergranular layer was more homogeneous with increasing sintering temperature, when sintering by direct heating and rapid cooling mode showed the best distribution of intergranular layer. These microstructural changes affected electrical characteristics directly, at 140$0^{\circ}C$ and C mode obtained high value of electrical resistivity and nonlinear exponent. Varistor voltage decreased with increasing sintering temperature, increased with decreasing holding time at high temperature. Barrier voltage obtained by calculation was about 1.5V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.359-362
• /
• 1998

Electrical breakdown characteristics of liquid nitrogen(LNd used as both coolant and insulator for high $T_c$ superconductor system is very important. This paper presents dynamic breakdown characteristics of liquid nitrogen by quench penomena of thermal bubble under high electric field. As the result, the breakdown mechanism of $LN_2$ depends on thermal bubble effect. The breakdown voltage decreases slightly with increasing heating. In the Electrode arrangement, electrical breakdown voltage of horizontal arrangement appears lower than that of vertical arrangement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.150-153
• /
• 1999

The electrical and physical characteristics of MgO and Pt thin-films on Si wafers deposited by r.f magnetron sputtering, were analyzed with annealing condition(100$0^{\circ}C$, 120 min) by four point probe, SEM and XRD. Until annealing temperature of 100$0^{\circ}C$, MgO had the properties of improving Pt adhesion to SiO$_2$ and insulation without chemical reaction to Pt thin-films and the resistivity of Pt thin-films was improved. The thermal characteristics of Pt micro-heater were analyed with Pt-RTD integrated on the same substrate, In the analysis of properties of Pt-RTD, TCR value had 3927 ppm/$^{\circ}C$ and liner in the temperature range of 25~40$0^{\circ}C$ temperature of Pt micro-heater had up to 40$0^{\circ}C$ with 1.5 watts of the heating power.