• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.9-12
• /
• 2005

This paper investigated the temperature history of mass concrete mock up structure considering different heat generation by varying with mixture proportion. Setting time difference between high early strength mixture (E-P) and retarding mixture (R-F30) was 14.5hours. Incorporation of $30\%$ of fly ash contributed to $10^{\circ}C$ of hydration heat reduction. In generally used C and D combination, bottom concrete shows earlier hydration, while E-J combination showed reverse tendency and thus, this method can reduce the crack occurrence. Therefore, heat generation difference method has beneficial effect on reducing crack induced by hydration heat resulting from heat generation difference between surface and center section.

• Fibers and Polymers
• /
• 제5권1호
• /
• pp.19-24
• /
• 2004

PET yarns textured at different texturing conditions were treated with superheated steam or dry heat at different temperatures for different times. The effects of the treatment conditions on the thermomechanical and structural changes of the yarn were examined by shrinkage, X-ray diffraction and birefringence measurements. With increase in superheated steam temperature, the crystalline orientation factor and birefringence decreased, whereas crystal size increased. Dry heat treatment had a smaller effect on shrinkage and structural properties in comparison with superheated steam treatment. The additional shrinkage after texturing process was investigated. The effect of heat-setting in both media was more significant at $200^{\circ}C$. The time dependence of the properties was not linear.

• Journal of Advanced Marine Engineering and Technology
• /
• 제8권2호
• /
• pp.81-87
• /
• 1984

The effect of heat treatment and mechanical stress on the dielectic strength of epoxy resin film is studied. The film with 30-210 .mu.m thickness are casted at room temperature for 8 hours and post cured at the range of temperature 60-180 .deg. C, and the heat setting time are two kind, ie, 2 and 10 hours. The samples are made with Stycast 1266 that the primary compound is diglycidyl ether of bisphenol A, and the hardner is denaturated polyamines. Under no mechanical stresses, the maximum dielectric strength of the sample is obtained for the sample heat treated for 2 hours at 150 .deg. C. However, the best dielectric strength characteristics under compressive stress is obtained for the sample heat treated at 90 .deg. C and 120 .deg. C. The dielectric strength of the sample are also affected significantly by the cooling velocity of the sample after post heat setting at given temperature.

• 한국건설순환자원학회논문집
• /
• 제3권1호
• /
• pp.80-86
• /
• 2007

In this study we experimented setting time and basic properties as waste wood fiber and sodium silicate substitution rate to reuse waste wood fiber produced in construction field to wood chip board. To do this construction waste woods were crushed with the size less than 10mm, mixed with the rate of 1:2, 2.5, 3, and added sodium silicate with the rate of 0, 5% of cement content. The results are as follows. As the substitution rate of construction waste wood was increased delay of setting time was also increased, and the batch of adding 5% accelerator had a 13~17 hours faster setting time than non accelerator batch. The compressive strength was lower as wood substitution rate was higher, and as the specific gravity was higher, the strength was also higher. As wood substitution rate was higher, heat conductivity was lower, and as specific gravity was higher, heat conductivity also was higher.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.505-508
• /
• 2004

This paper investigated the setting and compressive strength of concrete with the combination of mineral and chemical admixture. According to test results, plain concrete with high early strength development type AE water reducing agent(HEAEWRA) and $10\%$ of CKD respectively had earlier setting time than concrete with AE water reducing agent by $0.5\~1.5$ hours. Setting time of concrete with retarding type AE water reducing agent(RAEWRA) and FA $30\%$, BS $60\%$ respectively retarded by as much as $4\~7.5$ hours compared with plain concrete. Plain concrete with HEA WRA, $10\%$ of CKD and RAEWRA had higher strength than that of AE water reducing agent by as much as 5MPa at 28days. From the result of the paper, it is found that the combination of mineral admixture and setting accelerating or retarding agent can reduce the hydration heat cracks by setting time difference and hydration heat reduction effects.

• 태양에너지
• /
• 제18권1호
• /
• pp.81-89
• /
• 1998

In this paper an experimental was done to design combustion chambers which is required radiation strength of high temperature generator of absorption rigerator. Partiqularly, in combustion chamber radiative mediums were set and basic experiments were done according to its size by radiation strength and effects of heat transfer promotion. The results are as follows : 1) When radiative mediums were set in small combustion furnace burning nonframely radiative heat transfer was effected. 2) In case that area ratio($A/A_o$) of radiative medium is 0.82 or over, temperature fluctuation effects of furnace inside were not nearly. 3) In experimental boundary heat transfer effects were 1.8 times by setting up radiative medium. Specially, $q/{\Delta}T$ values of furnace inside were uniformed nearly by setting up radiative mediums.

• 열처리공학회지
• /
• 제25권3호
• /
• pp.121-125
• /
• 2012

The large forgings used in chemical plants or nuclear power plants are produced by complex heat treatment. because of thickness up to 200~300 mm and weight up to 200~300 ton, setting proper heat treatment cycle is so difficult. In addition, defects of products make companies wasting large money and valuable time. In this study, to reduce try & err, when setting heat treatment of reactor pressure vessel steel SA508Gr.3, carrying out the basic mechanical property test of SA508 Gr.3 and testing hardness of SA508Gr.3 in various tempering temperature. and calculating temper curve with Hollomon-Jaffe parameter.

• 한국염색가공학회지
• /
• 제17권3호
• /
• pp.8-15
• /
• 2005

Cationic dyeable polyester(CDP) fabric was annealed at varying temperatures range from $120^{\circ}C$ to $220^{\circ}C$ for 1, 3, and 5 min under tension. Dyeing rates of CDP fabrics were measured with cationic and disperse dyes at $100^{\circ}C$ and $120^{\circ}C$ in water system. Also X-ray diffraction pattern, DSC thermograms and dyeability of fabric with cationic and disperse dyes were investigated. The intensities of X-ray diffraction peaks of annealed fabric were increased with increasing in annealed temperature, and peak became sharp with heat setting temperature. The apparent color depth (K/S) of CDP fabric initially decreased with increase of heat-setting temperature up to $160\~180^{\circ}C$ and then increased at higher temperature. The shearing modulus(G) and surface roughness were increased with annealing temperature.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.54-54
• /
• 2010

In this study, the correlation between temperature and the gel-content of the module were analyzed through experiments. Amorphous thin-film solar cell used in this experiment has a visible light transmission performance of 10%. In addition, ethylene vinyl acetate(EVA) film and the clear glass have been used for the modulation. The most important process is to laminate the module in the manufacturing process of BIPV(Building integrated photovoltaic) module. Setting parameters of laminator in the lamination process are temperature, pressure and time. Setting conditions significantly affect the durability, watertightness and airtightness of module. The most important factor in the setting parameters is temperature to satisfy the gel-contents. The bottom and top surface temperature of module are measured according to setting temperature of laminator. The results showed $145^{\circ}C$ of max temperature of the bottom surface and $128^{\circ}C$ of max temperature of top surface on the module at the temperature condition of $160^{\circ}C$. And at the another temperature condition of laminator with $150^{\circ}C$, the max temperature do bottom and top are $117^{\circ}C$ and $134^{\circ}C$ respectively. The temperature difference between bottom and top of the module occurred, that is because heat has been blocked by the clear glass and the bottom of the cells absorb the heat from the laminator. In this particular, the temperature difference between setting temperature of the laminator and the surface temperature of the module showed $15^{\circ}C$, because the heat of laminator plate is transferred to the surface of the module and heat is lost at this time. As a results, gel-content showed 94.8%, 88.7% and 81.7% respectively according to the setting temperature $155^{\circ}C$, $150^{\circ}C$ and $145^{\circ}C$ of the laminator. In conclusion, the surface temperature of module increases, the gel-contents is relatively increased. But if the laminator plate temperature is too high, the gel-content shows rather decline in performance. Furthermore, the temperature difference between setting temperature and the surface temperature of the module is affected by laminating machine itself and the temperature of module should be considered when setting the laminator.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.935-938
• /
• 2001

This paper reports the relation of concrete setting characteristic and lateral pressure in mass concrete wall such as side wall of LNG underground storage tank. In order to estimate the lateral pressure, initial setting time of low heat cement concrete with type of mineral admixture was measured for three concrete mixtures(W/P=41.6%) containing limestone powder, fly ash, and slag powder. As a result, the lateral pressure of the concrete containing limestone powder was the smallest than those of other concretes as well as the initial setting time.