• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.631-639
• /
• 1996

Electrosurgical technique have been used in dentistry as an aid to soft tissue management for nearly 60 years. However, it was not until the late 1960s that the principles of electrosurgery were understood and improved equipment became available. Electrosurgery is a surgical procedure performed on soft tissue utilizing controlled high frequency electricaI(radio-frequency) currents in the range of 1,500,000 to 7,500,000 cyclesper second. The radio-frequency energy used in electrosurgery is able to cut and coagulate tissue because it focuses the energy at the small, active electrode. Advantages of electrosurgery for soft-tissue management during dental procedures include improved hemostasis, ease of tissue modification, improved visibility and so on, but adverse healing responses-including necrosis of soft tissue and sequestration of alveolar bone-have been reported. The present report provides examples of treatment of soft tissue and pulp tissue of primary teeth by electrosurgery. The results are as follows; 1. Electrosurgical techniques can be used for various procedures in pedodontics. 2. Electrosurgical procedures provide improved hemostasis and visibility in the operating field, which enable to remove, reshape, and contour soft tissues easily. 3. In pulpotomy technique, it was difficult to expect the variable pulpal response based on the degree of heat accumulation and the conditions of pulp tissues. Therefore, electrosurgical pulpotomy could not be considered as a method superior to formocresol pulpotomy. 4. A greater degree of dexterity and experiences in manipulation of the electrode is required compared with the conventional scalpel surgery.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.49-54
• /
• 2000

Cr-Mo-V steel is widely used as a material for the turbine structural component in fossil power plants. It is well known that this material shows the various material degradation phenomenons such as temper embrittlement, carbide coarsening. and softening etc. or ins to the severe operation conditions as high temperature and high pressure. These deteriorative factors cause tile change of mechanical properties as reduction of fracture toughness. Therefor it is necessary to evaluate tile extent of degradation damage for Cr-Mo-V steel in life assessment of turbine structural components. In this paper. the electrochemical potentiokinetic reactivation(EPR) test in $50wt%-Ca(NO_3)_2$ solution is performed to develop the newly technique for degradation damage evaluation of Cr-Mo-V steel. The results obtained from the EPR test are compared with those in small punch(SP) tests recommended by semi-nondestructive testing method using miniaturized specimen. The evaluation parameters used in EPR test are tile reactivation current density$(I_R)$ and charge$(Q_{RC})$ reactivation rate$(I_R/I_{Crit},\;Q_R/Q_{Crit})$. The results suggest that $I_R/I_{Crit}$ in these parameters shows a good correlation with SP test results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.5 no.2
• /
• pp.275-278
• /
• 1992

One hundred sixty three (163) animals were used in $2{\times}2$ and $3{\times}2$ factorial experiment in randomized complete block design (RCBD) to determine the effect of clitoral stimulation during timed inseminations on the fertility of Philippine swamp buffaloes (carabaos). There were 3 separate trials conducted with two treatment groups per trial : control and with 30 second clitoral stimulation after each insemination. Parity, tone of uterus and site of semen deposition were also used as criteria in subdividing the main groups. The pregnancy rates of animals that received clitoral stimulation were significantly (p<0.05 or p<0.01) higher than those of control for both caraheifers (52.98 vs 31.41%) and caracows (52.68 vs 27.07%) ; under all uterine conditions : tone 1 (53.33 vs 31.75%), tone 2 (35.83 vs 22.82%) and tone 3 (75.65 vs 42.44%) ; and in both site of semen placement, cervix (43.99 vs 22.85%) and uterus (60.92% vs 37.81%). Fertility was also significantly (p<0.05) higher when semen was deposited in the uterus (49.37%) than in the cervix (33.42%). Interaction effect was insignificant. Clitoral stimulation should be utilized as a routine procedure following artificial insemination in carabaos.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.429.2-429.2
• /
• 2014

ZnO nanowire is known as synthesizable and good mechanical properties. And, stimuli-responsive polymer is widely used in the application of tunable sensing device. So, we combined these characteristics to make precise tunable sensing devise. In this work, we investigate the dependence of ZnO nanowire alignment and morphology on si substrate using nanosphere template with various conditions via hydrothermal process. Also, pH-temperature dependant tuning ability of nanostructure was studied. The brief experimental scheme is as follow. First, Zno seed layer was coated on a si wafer ($20{\times}20mm$) by spin coater. And then $1.15{\mu}m$ sized close-packed PS nanospheres were formed on a cleaned si substrate by using gas-liquid-solid interfacial self-assembly method. After that, zinc oxide nanowires were synthesized using hydrothermal method. Before the wire growth, to specify the growth site, heat treatment was performed. Finally, NIPAM(N-Isopropylacrylamide) was coated onto as-fabricated nanostructure and irradiated by UV light to form the PNIPAM network. The morphology, structures and optical properties are investigated by FE-SEM(Field Emission Scanning electron Microscopy), XRD(X-ray diffraction), OM(Optical microscopy), and WCA(water contact angle).

• Korean Journal of Materials Research
• /
• v.27 no.5
• /
• pp.281-288
• /
• 2017

In this study, Fe-Ni slag, converter slag and dephosphorization slag generated from the steel industry, and fly ash or bottom ash from a power plant, were mixed at an appropriate mixing ratio and melted in a melting furnace in a mass-production process for glass ceramics. Then, glass-ceramic products, having a basalt composition with $SiO_2$, $Al_2O_3$, CaO, MgO, and $Fe_2O_3$ components, were fabricated through casting and heat treatment process. Comparison was made of the samples before and after the modification of the process conditions. Glass-ceramic samples before and after the process modification were similar in chemical composition, but $Al_2O_3$ and $Na_2O$ contents were slightly higher in the samples before the modification. Before and after the process modification, it was confirmed that the sample had a melting temperature below $1250^{\circ}C$, and that pyroxene and diopside are the primary phases of the product. The crystallization temperature in the sample after modification was found to be higher than that in the sample before modification. The activation energy for crystallization was evaluated and found to be 467 kJ/mol for the sample before the process modification, and 337 kJ/mol for the sample after the process modification. The degree of crystallinity was evaluated and found to be 82 % before the process change and 87 % after the process change. Mechanical properties such as compressive strength and bending strength were evaluated and found to be excellent for the sample after process modification. In conclusion, the samples after the process modification were evaluated and found to have superior characteristics compared to those before the modification.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.4
• /
• pp.221-225
• /
• 1999

This paper shows the parameters to affect the critical characteristic of YBaCuO superconducting bulk fabricated by MPMG (Melt Powdered Melt Growth)process. In order to investigate proper processing variables, the effect of the holding time at the melting temperature and that of the slow cooling time in $O_2\; ambient\; on\; the\; J_c$ were experimented. And then with the above obtained heat treatment conditions, the effects of addition of $Y_2BaCuO_5\; and\; Ag\; on\; the\; J_c$ were also investigated. A proper slow cooling time yields phase transformation from Tetragonal $(YBa_2Cu_3O_6)$ to Orthorhombic $(YBa_2Cu_3O_7)$ during an annealing time in $O_2$. Ag addition plays a role in increasing the $T_c\; and\; the J_c$, but the magnetization decreases. The $J_c$ and the magnetization increase with addition of Y211. $J_c$ of the sample added Ag 10wt% is superiorover 3000 G. Proper holding time, slow cooling time and amount of impurity addition are important parameters in fabricating the YBaCuO bulk by MPMG process with high $J_c$.

• Journal of Life Science
• /
• v.9 no.1
• /
• pp.111-120
• /
• 1999

A bacteriocin-producing strain, J-105, was isolated from Kimchi and identified as Lactococcus sp. The optimum conditions for the bacteriocin production from the isolated microorganism were evaluated. For maximum yield of bacteriocin from Lactotoccus sp. J-105, the cell should be harvested at the early stationary phase and temperature, pH and NaCl concentration should be $25^{\circ}C$, pH 8.0 and without the addition of NaCl, respectively. Maltose should be used as a carbon source and organic nitrogen such as polypeptone should be used as a nitrogen source for the best yield. The bacteriocin from isolate was inhibitory against Acetobacter aceti, Bacillus subtilis and several strains of lactic acid bacteria. The bacteriocin of J-105 was sensitive to pepsin, but stable for heat treatment. It was stable even at autoclaving temperature for 15 min.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.57-63
• /
• 1999

A thin metal plate such as detent spring has the shape deformation due to the phenomenon of spring back after press machining and heat treatment process. This requires the correction of spring shape and force in final inspection process. To do correction of the shape deformation the impact force is manually applied to the bended part of detent spring after measuring the shape deformation and spring force. To develop the automatic spring force correction system, applied force of occurring plastic deformation must be derived from the experimental method. But frequent change of spring shape and material makes it difficult to accomplish the experimental method to be applied. This paper describes the analytical method for detent spring force correction system is to be substituted for the experimental method. FEM(Finite Element Method) is used to find the boundary value between elastic and plastic deformation in the analytical method. To confirm the validity of the analytical method, the result of two methods is compared each other at various applied force conditions. It shows that the simulation result of the analytical method is consistent with the result of the experimental method within the error bound ${\pm}$5%. The result of this paper is useful for development of the automatic spring correction system and reduction of the complicated and tedious processes involved in experimental method.

• The Journal of Korean Physical Therapy
• /
• v.12 no.2
• /
• pp.191-201
• /
• 2000

This study was investigated the effects of a direct current and ultrasound on transdermal transport of dexamethasone into the rabbits which had contusion in the thigh. Each group was treated under the tallowing conditions. 1. EXP group I : $10\%$ dexamethasone ointment and ultrasound 2. EXP group II : $1\%$aqueous solution of dexamethasone and iontophoresis 3. EXP group III : the application of $10\%$ dexamethasone ointment 4. Control group : No treatment The degree of anti-inflammation was evaluated by the naked eye, the change in girth of thigh, and a light microscope. The results were as follows. 1.8y the naked eye. an inflammation sign was seen in all groups and especially. symptoms of redness. heat swelling were prominent in EXP group I. 2. In comparision in the change of girth of thigh, only EXP group II showed no significant change. Therefore, it meant that there was effective anti-inflammatory reaction in EXP group II. 3. The infiltration of inflammation cells, the degree of swelling, and the degree of crosslinking of connective tissues were evaluated with a light microscope. As a result, EXP group II showed the most effective anti-inflammatory reaction. And, in order of EXP group III, control group, the effect of anti-inflammation reaction was decreased. 4. EXP group I showed more intensive inflammation than control group.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.580-587
• /
• 1996

Synthesis of long fibrous $K_2Ti_4O_9$ was attempted to find a method to produce long fibrous $K_2Ti_6O_{13}$ and other derivatives and also phase transformation of $K_2Ti_4O_9$ synthesized was investigated. Long fibrous $K_2Ti_4O_9$ was succesively synthesized by the calcination reaction under the following reaction conditions ; reaction temperature of $1050^{\circ}C$, $TiO_2$ mole ratio to $K_2CO_3$ of 2.8 and reaction time of 3hrs, and scattering of calcined products for 10hrs with hot boiling water. $K_2Ti_4O_9$ showed lower structural stability under heat treatment and the structure of $K_2Ti_4O_9$ was converted to $K_2Ti_6O_{13}$ under heating temperature of over $250^{\circ}C$.