• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.69-75
• /
• 2015

Stone board for the rock bed was needed to reduce weight using thin thickness and reinforced materials. In this work, stone/wood board for rock bed was studied. Stone and wood were attached to reduce total weight of stone for rock bed. For reinforcing wood heat treatment method was used to change surface and mechanical properties. Mechanical strength of heat treated wood increased more than neat condition. The optimum heat treatment condition was set on $100^{\circ}C$ under tensile, flexural loads whereas surface energy was also obtained by contact angle measurement. Optimum adhesive condition was to get the maximum adhesion between stone and wood. Lap shear test was performed for stone/wood board with different adhesives such as amine type epoxy, polyurethane, chloro-rubber and vinyl chloride acetate type. Fracture surface of lap shear test was shown at wood fracture part on stone using amine type epoxy adhesive. It was found that for high adhesion between stone and wood the optimum adhesive was epoxy type for the rock bed.

• The Journal of Internal Korean Medicine
• /
• v.38 no.3
• /
• pp.401-407
• /
• 2017

Objective: This study reports on a treatment case of Soojeom-san plus Jeungmiyijin-tang (SJJI) on gastroesophageal reflux disease with hiatal hernia. Method: We considered a male patient suffering from gastroesophageal reflux disease with hiatal hernia because of blood stasis and damp-heat of the spleen and stomach pattern and prescribed SJJI. The progress was evaluated using the frequency scale for the symptoms of gastroesophageal reflux disease (FSSG) score, and the visual analogue scale for abdominal pain, sore stomach, and other symptoms. Results: The patient's symptoms, which included abdominal pain, sore stomach, dyspepsia, anorexia, insomnia, etc., almost disappeared. Conclusion: SJJI can be used for patients who have a chronic condition of gastroesophageal reflux disease with hiatal hernia because of blood stasis and a pattern of damp-heat of the spleen and stomach.

• Preventive Nutrition and Food Science
• /
• v.12 no.4
• /
• pp.251-258
• /
• 2007

Thermal resistance and heat activation characteristics of Clostridium botulinum ATCC 25763 spores were evaluated. The effects of nisin and pH on the activation and subsequent germination were also investigated. Spores of C. botulinum were not inactivated by heat treatments up to $92^{\circ}C$ for 2 hr. Heat treatment at $85^{\circ}C$ for 90 min was selected as the optimal activation condition based on monitoring subsequent germination. L-alanine alone or in combination with L-cysteine was not sufficient to germinate the spores of this strain. Tryptone-Peptone- Glucose-Yeast extract (TPGY) broth supplemented with L-alanine was used as a suitable germination medium. Decreasing pH of activation suspension increased the degree of phase darkening, i.e., germination. In addition, the presence of nisin during activation increased the degree of phase darkening. The majority of spore populations were dormant at a pH of less than 2.8, and these populations required heat activation to increase the culturability on TPGY agar medium. However, extended heating in the presence of nisin at pH 2.8 decreased the spore count; however, heat activation was less necessary at pH 3.4, compared at pH 2.8.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.159-164
• /
• 1996

For the purpose of establishing laser welding condition(laser power, welding speed and beam focus) and of evaluating tailor welded blank for three kinds of thin steel sheets of SPCC, SK5M and SUS304 using in the thin plate structure such as automobile, train and so on. Their $CO_2$ laser weldability were primarily tested under various welding condition. SPCC and SUS304 thin sheets showed good weldability under some welding condition. But, high carbon steel sheet SK5M needs heat treatment after welding to obtain higher tensile strength and ductility of the welded joint. And next, laser welding condition. Butt-welded specimens were not nearly broken at weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor welded blank were SPCC+SPCC=22~25mm, SUS304+SUS304=25~43mm and SK5M+SK5M=13~17mm.

• Journal of Korea Foundry Society
• /
• v.38 no.5
• /
• pp.87-94
• /
• 2018

The effects of Sr and (Ti-B) additives on the tensile properties of AC4A recycled (35% scrap content) aluminum alloys were investigated. An acicular morphology of the eutectic Si phase of as-cast specimens was converted to a fibrous morphology upon the addition of Sr. Moreover, morphology of the Sr modified eutectic Si phase became finer due to a T6 heat treatment. The grain size of the ${\alpha}$-solid solution was decreased by the addition of (Ti-B) additives. Depending on the treatment conditions of the as-cast specimens, i.e., no addition, a Sr addition and a (Ti-B)+Sr addition, the tensile strength levels of the as-cast specimens were 182, 192, and 204MPa, respectively. The corresponding strengths of T6 heat-treated specimens were 293, 308, and 318MPa. Elongations of the as-cast specimens were 2.2, 3.1, and 5.6%, and the corresponding elongations of the T6 heat-treated specimens were 4.6, 6.1, and 7.6%. The percentage of the reduced section area in the tensile specimens was also increased by the Sr and (Ti-B) additives. Sr and (Ti-B) additives changed the microstructure and the distribution of defects in the castings, resulting in an improvement of the tensile properties of AC4A aluminum alloys. According to our test results, recycled (35% scrap content) AC4A aluminum alloy met all of the KS requirements of the tensile strength and elongation values of AC4A aluminum alloy except for the elongation value of the one specimen condition, in this case the as-cast no-addition condition.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.249-254
• /
• 1998

In relation to the application of magnetic method to the evaluation of irradiation damage (embrittlement) changes in the magnetic parameters(hysteresis loop and Barkhausen noise) and Vickers microhardness due to neutron irradiation and heat treatment were measured and compared. In the case of irradiation $(2.3{\times}10^{19}\;n/cm^2,\; E{\ge}1\;Mev,\; 288{\circ}C)$ hysteresis loop measurements show that susceptibility decreases as coercivity increase. Saturation magnetization do not show any change. Barkhausen noise amplitude and Barkhausen noise energy have decreased while Vickers microhardness has increased. For isothermally heat treated condition of irradiated specimen at 470 $^{\circ}C$ and 540 $^{\circ}C$, Barkhausen noise energy has increased while Vickers microhardness has decreased. Results of BNE and Vickers microhardness are reversed to the results on irradiated condition. All these consistent changes in magnetic parameter and Vickers microhardness measurement, which are thought to be resulted from the interaction between irradiation-induced defects and dislocation, and magnetic domain, respectively, show a possibility that magnetic measurement may be used to the evaluation of material degradation and recovery due to neutron irradiation and heat treatment, respectively, if a relevant large database in prepared.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.252-255
• /
• 1996

Superconducting current lead is one of the promising applications of the oxide high-Tc superconductors, because they have the advantage of decreasing heat conduction to low temperature region, comparing with a conventional cooper alloy lead. High critical current density is a key factor for the applications such as current lead. (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$\_$x/ high Tc superconductor haute been investigated in terms of critical current density. Bi-2223 superconducting current lead made by CIP and solid state sintering process. Bi-2223 current lead that heat treated at 836$^{\circ}C$ for 240 h in 1/13 P$\_$O$_2$/ had over 150 A/$\textrm{cm}^2$ of critical current density at 77K. We knew that the superconducting properties of tube type current leads were better than rods type of them. And we investigated the relation of Bi-2223 formation and heat treatment condition by XRD and SEM analysis.

• Journal of Power System Engineering
• /
• v.3 no.3
• /
• pp.76-82
• /
• 1999

This study presents a methodology to predict the hardenability of quenched carbon steels. The equation of transient heat conduction is analyzed to formulate a cooling curve by a finite element method which incorperates coupled effects of temperature on physical properties, the metallic structures and also the latent heat by phase transformation. The volume traction of martensite and pearlite are the structural analysis for hardenability analysis. In order to demonstrate the feasibility of adopting a full quench model respectively. This procedure could be used as the database for optimal condition of heat treatment processes.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.3
• /
• pp.134-142
• /
• 1994

$Al_2O_3$coatings on mild steel substrate by plasma spray process were produced to evaluate microstructural characterization and mechanical properties. As-coated $Al_2O_3$coating samplessd were subjected to two heat treat-ment conditions : ⅰ) annealing under vacuum circumstance, ⅱ) hot press treated condition. The two heat treat-ed coatings were investigated in terms of microhardness, adhesion strength, wear resistance, porosity forma-tion, and microstructures. In the case of the coatings which were subject to preparation step ⅰ, the porosity in the coating was decreased with the increase of temperature ($700^{\circ}C$-$1100^{\circ}C$), and the wear resistance, microhardnesss and adhesion strength were increased with the increase of temperature. On the other hand, in the case of the coatings which were subject to preparation step ⅱ, wear resistance and adhesion strength were improved with the increase of temperature and pressure. Experimental measurements of coatings which were produced by both preparation conditions were enhanced compare to those of as-coated coatings.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1494-1496
• /
• 1997

The MRI Magnet is a most practical application of NbTi superconductor. In this paper, we present the main research results on superconducting wires for MRI magnet which we have developed. Cu/NbTi superconducting wires were fabricated by repeat of cold working and heat-treating process after that billets were extruded. We investigated the relation of superconductivities of wires and heat treatment condition. The correlation between cross section shape of wires and work inhomogeneity of NbTi rods was investigated by microscopic observation. The more repeatation number of cold working and heat-treating process, the higher critical current is achieved.