• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.43-46
• /
• 1997

The interfacial bond strength and microstructural analysis of pre-heat treated porcelain-fused-metal (PFM) were investigated using a mechanical three-point bending tester and scanning electron microscope(SEM). Four kinds of heat treated samples were prepared as follows; A: heating $1200^{\circ}F\rightarrow1600^{\circ}F$, holding 1min, reheating $\rightarrow1850^{\circ}F$, hold 3min under vacuum, B: heating $1200^{\circ}F\rightarrow1600^{\circ}F$ holding 1min, reheating $\rightarrow1850^{\circ}F$ under vacuum condition, C: heating $1200^{\circ}F\rightarrow1600^{\circ}F$, holding 1min, reheating $\rightarrow1850^{\circ}F$, holding 3min in the air, repeat same heat treatment process under vacuum condition, D: heating $1200^{\circ}F\rightarrow1600^{\circ}F$, holding 1min, reheating $\rightarrow1850^{\circ}F$, holding 1min in the air. The three-point bending test results shows that the interfacial bond strength of specimen B and C were higher than that of A and B. The SEM study reveals that Specimen C shows the highest surface density.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1387-1393
• /
• 1996

A study on mesophase pitch as a matrix precursor of carbon fiber reinforced carbon (C/C) composite has been recently presented. This study is concerned with the production of mesophase pitch as matrix precursors for C/C composite from coal tar pitch. A commercial coal tar pitch was heat-treated at 25$0^{\circ}C$ for 2 hours to remove low molecular weight fraction from the pitch then increasing the temperature of the pitch to between 350~45$0^{\circ}C$ to produce mesophase pitch. The pitch was continuously stirred during this time and nitrogen gas was continuously bubbled through the pitch. Spherical and bulk mesophases were formed in the pitch after heat-treatment,. Parent and mesophae pitches were characterized by elemental analysis coke yield solubi-lity in tetrahydrofuran and hexane and an optical microscopy to measure the mesiophase content. It was neces-sary to produce C/C composite that a mesophase pitch with about 30-40 vol% mesophase spherulites can be infiltrated into a fiber preform without a filter effect as a matrix precursor conditions. This condition was satisfied with mesophase pitch heat treated at 40$0^{\circ}C$ for 2 hours. The other heat treatment conditions showed the nuclei of mesophase or bulk mesophae which were not satisfied with the matix precursor condition.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1603-1605
• /
• 1997

$LiNiO_2$ is prepared by heating LiOH $H_2O$ and $Ni(OH)_2$ (mole ratio 1:1). In this study, we investigated X-ray diffraction, and charge/discharge property heat treatment condition and conductive agent sort and volume of $LiNiO_2$ prepared at various temperature and time. All $LiNiO_2$ prepared at this study showed hexagonal structure. In charge/discharge capacities, heated at $O_2$ than air and $750^{\circ}C$ than $700^{\circ}C$, specific capacity is higher. Therefore, when preliminary heat at $650^{\circ}C$ $O_2$ and heat at $750^{\circ}C$ carried out, charge/discharge property is best.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.4
• /
• pp.165-172
• /
• 2013

In the present study, the microstructure and solution treatment response of Al-Zn-Mg alloys bars by thixo-extrusion was investigated. The alloy bars were solution treated at 400, 430, 460 and $490^{\circ}C$ for various times. In order to examine the microstructures and phase analysis of the samples after solution treatment, it was performed by optical and scanning electron microscopy. And, Vickers hardness and electrical conductivity was measured on the solution treated samples for each condition to investigate the solution treatment response of extruded bars during solution treatment. The results show that the optimum solution heat treatment conditions of thixo-extruded Al-Zn-Mg alloy for minimization of the grain growth and degradation promotion of the second phase is a temperature of $460^{\circ}C$ and holding time of 0.5 to 2 h.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 1999.10a
• /
• pp.46-57
• /
• 1999

Ginseng(Panax ginseng C.A. Meyer) is important medicinal plant but requires 4-year cultivation for root harvest because of slow growth. In contrast, ginseng callus and hairy roots grow vigorously and may Produce the same or more biologically active compounds for human health than natural ginseng roots. Therefore, ginseng callus and hairy roots can be used for commercial purposes. Polyacetylene, one of anti-cancer compounds in ginseng, was not detected in the callus cultured on the medium containing 2, 4-B, but cells derived from the callus growth was excellent, The ginseng calli cultured on the medium containing 2mg11 CPA and 0.05mg/1 BA was grown vigorously and produced panaxydol, one of ginseng polyacetylene. The biosynthesis of polyacetylene in callus was not affected by addition of NAA and sucrose in media. The SH medium was better than the MS medium for ginseng callus growth and biosynthesis of panaxydol. Another ginseng anti-cancer compounds, ginsenoside-Rg$_3$, Rh$_1$and Rh$_2$ were detected in ginseng hairy roots by heat treatment. Those of Panax ginseng were obtained after root disks of three-year old roots were infected with Agrobacterium rhizogenes Rl000 $A_4$T in dark condition after one month of culture. The optimum growth of hairy roots was achieved in the culture of 1/2 MS liquid medium in dark(22$^{\circ}C$) under 60 rpm gyratory shaking. Hairy roots grew well in 5 ι Erlenmeyer flasks, 1ι roller drums, 10ι jar-fermenters, and especially in 20ι air-lift .culture vessels. All heat treatments had remarkably different ginsenoside contents. Eleven ginsenosides were determined in heat treatment, eight in freeze dried hairy roots. Contents of ginsenoside-Rbl , Rb2, Rc, Rd. Re, Rf, and Rg$_1$tested in all heat treatments were less than those of freeze dried hairy roots. Contents of glnsenoside-Rg$_2$ in heat treatment for 1 hour at 105$^{\circ}C$ was 4.92mg/g dry wt, 3.9 times higher than 1.27 mg/g dry wt of freeze dried hairy roots. The optimum condition of heat treatment for the production of ginsenoside-Rg$_3$and Rhl was 2 hours at 105$^{\circ}C$, and ginsenoside content was 2.58mg/g dry wt and 3.62mg/g dry wt, respectively. The production of ginsenoside-Rh2 was the highest in heat treatment for 2 hours at 105$^{\circ}C$ among treatments examined, and ginsenoside-Rh$_2$content was 1.08mg/g dry wt.

• Proceedings of the Safety Management and Science Conference
• /
• 2009.04a
• /
• pp.413-421
• /
• 2009

This paper investigates tensile characteristics of the stress aging heat-treated SM45C steel which are aging temperature at $250^{\circ}C$, $300^{\circ}C$, aging time at 1, 3 hours, and applied load at 300, 400N conditions by using acoustic emission. Most suitable aging condition was aging temperature $300^{\circ}C$, aging time 1 hour, and aging applied load 300N. And increased yield load 28.3% than non-treatment specimen in this condition. AE energy in elastic limit increased about 16.7 times than non-treatment specimen. When aging time is 3 hours, yield load decreased than other conditions that possibility is high to have itself defect on inside the specimen or coarse grain size precipitation is different in happened over-aging phenomenon. Especially, in case of $300^{\circ}C$, 3 hours and 400N condition appeared AE energy in elastic limit fairly high about 30 times than non-treatment specimen. This is considered by emit a lot of energies when material causes plastic deformation because the ductility increases on specimen by over-aging phenomenon.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.1
• /
• pp.20-28
• /
• 2012

The monofilament with 0.304mm of diameter was produced using a polybutylene succinate (PBS) resin, and a gill net was made by it. We investigated the impact of heat setting temperature on the mechanical properties, knot state and height of gill net. Heat treatment was carried out using the high pressure steam machine for 20 minutes at temperature of $55^{\circ}C$, $60^{\circ}C$, $70^{\circ}C$ and $75^{\circ}C$. Before heat treatment, the strength and elongation of PBS monofilament were estimated to be $48.1kg/mm^2$, 23.8% at unknot, $37.6kg/mm^2$, 18.8% at single knot, $26.6kg/mm^2$, 22.9% at double knot in dry condition, respectively. The strength and elongation of PBS monofilament with double knot were decreased as heat setting temperature increased, and the decreasing rate of strength was showed to be higher than that of elongation. It was not found any differences in strength and elongation of PBS monofilament yarn with double knot at the $65^{\circ}C$ and $70^{\circ}C$ of heat setting temperature by 5% significance of T-test, but there was a significant difference at the $70^{\circ}C$ and $75^{\circ}C$ of heat setting temperature. The net's height and length from leg to leg appeared no differences at the $70^{\circ}C$ and $75^{\circ}C$ of heat setting temperature. In results, it was investigated that the PBS monofilament gill net with the maximized physical properties could be manufactured at $70^{\circ}C$ of heat setting temperature using a high pressure steam machine for 20 minutes.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.26-31
• /
• 2004

In order to propose the optimum welding condition for field application, the effects of welding heat input and cooling rate at PWHT on the mechanical properties were investigated. Submerged arc welding of 1.25Cr-0.5Mo steel for pressure vessel was conducted at welding heat inputs of 15.2kJ/cm, 30.9kJ/cm, and 44.8kJ/cm, and cooling rates of 184$^{\circ}C$/hr, 55$^{\circ}C$/hr, and 2$0^{\circ}C$/hr at PWHT. From the test results, as the welding heat input increase up to 30.9kJ/cm, the changes of microstructure and impact toughness were small. At the heat input of 44.8kJ/cm, however, toughness decreased obviously due to the coarsening of coarse-grained HAZ and formation of ferrite at bainite grainboundary of weld metal. On the other hand, cooling rates at PWHT did not effect on the changes in microstructure and mechanical properties. Even though tensile strength and impact toughness at all welding conditions of this study were above the minimum specification requirement, it was confirmed that heat input of 30.9kJ/cm was the optimum welding condition to improve welding performance by higher heat input.

• Journal of Applied Biological Chemistry
• /
• v.59 no.1
• /
• pp.69-74
• /
• 2016

The objective of this study was to examine the combined effect of fumaric acid with mild heat on the inactivation of microorganisms on spinach. Spinach leaves were inoculated with Escherichia coli O157:H7 and Listeria monocytogenes. Based on the results of single treatment of fumaric acid (0.1, 0.3, and 0.5%) or mild heat (40, 50, and $60^{\circ}C$) regarding the inactivation of the inoculated bacteria, the optimal condition for the combined treatment was suggested to be 0.5% fumaric acid and mild heat treatment at $50^{\circ}C$ for 5 min. The combined treatment of fumaric acid with mild heat caused 2.53 and 2.62 log reductions of the populations of L. monocytogenes and E. coli O157:H7, respectively. In addition, during storage of fresh spinach at $4^{\circ}C$ for 12 d, the combined treatment reduced initially the populations of total aerobic bacteria by 2.77 log CFU/g compared with the control. In particular, after 12 d of storage, the population of total aerobic bacteria for the combined treatment sample was 4.84 log CFU/g, whereas the control sample had 6.66 log CFU/g. Color and vitamin C content of spinach samples were not altered significantly by the combined treatment during storage. These results indicate that the combined treatment of fumaric acid with mild heat is an effective method to control microorganisms on spinach during storage.

• Food Science and Preservation
• /
• v.24 no.6
• /
• pp.820-826
• /
• 2017

Soybean is one of the most common food materials for making traditional Korean foods such as soybean paste, soy source and soy snack, and their manufacturing processes include heat treatment of soybean. This study was carried out to investigate the effect of heat treatment on the physicochemical properties of soybean. All samples were heat treated under commercial steamed, puffed or air-fried conditions, and then the protein molecular weight distribution, thermal properties, fluorescence intensity, protein solubility, and water and oil holding ability of the heat treated soybeans were examined. Sodium dodecyl sulfate polyacrylamide gel electrophoresis indicated that heat treatment caused fragmentation of polypeptide chain in soybean, showing the band of low molecular ranging from 17 to 40 kDa. The differential scanning calorimetric analysis showed the decrease of enthalpy values (${\Delta}H$) by heat treatment. Fluorescence spectroscopy indicated that the heat treatment caused lipid oxidation as proved by increasing emission intensity. The protein solubility at pH 3-6, and water holding capacity of heat treated soybeans were the higher than no treatment. These results suggest that the heat treatment resulted in decreased enthalpy values, and increased protein degradation, lipid oxidation and water affinity of soybean. Moreover, the effect of heat treatment on physiochemical properties of soybeans was more significant under air-fried condition.