• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.11
• /
• pp.3686-3694
• /
• 1996

A numerical investigation of natural convection flow along irregular vertical surfaces is reported. A transformation method is applied to the problem of natural convection under the assumption of a large Grashof number. A vertical wavy surface is used as an example to demonstrate the advantages of the transformation method, and to show the heat transfer mechanism near such surfaces. Surface non-uniformities on the boundary layer flow induced by a constant was temperature, semi-infinite surface are investigated. Also the effects of Prandtl number, flow index, and surface amplitude in Non-Newtonian fluids are discussed. When possible, the comparison of the numerical results shows a good agreement. The amplitude is proportional to the amplitude of a wavy surface. The results demonstrate that the local heat flux along a wavy surface is smaller than that of a flat surface. The frequency of the wavy surface is half that of the local heat transfer rate. The amplitude of the local Nusselt number gradually decreases downstream where the natural convection boundary layer grows thick.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.209-218
• /
• 2002

The temperature field of a counterflow non-premixed flame is investigated using thermocouples of two sizes. A thermal balance is performed on the thermocouple in order to calculate the magnitude of the radiation corrections involved. Both the thermocouple wire and bead are separately considered to be the relevant thermal surface to which convective heat transfer takes place, and from which radiation lasses occur. The flame is also simulated by using a detailed chemical kinetic mechanism in a previously developed computer code. The local thermo-physical properties of the gas mixture, required to calculate the corrections, are determined both from the simulation, and by approximating the properties of the mixture as those of molecular nitrogen at the measured temperatures. It is concluded that the thermocouple wire is the appropriate thermal surface to which radiation corrections apply, in the absence of information about the gas mixture, its properties can be reasonably approximated by those of nitrogen rm ($N_2$), and the radiation corrections are very sensitive to misalignments in the temperature and velocity fields.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.605-613
• /
• 2017

Recently, efficient heat dissipation has become necessary because of the miniaturization of devices, and research on boiling on micro-channels has attracted attention. However, in the case of micro-channels, the friction coefficient and heat transfer characteristics are different from those in macro-channels. This leads to large errors in the micro scale results, when compared to correlations derived from the macro scale. In addition, due to the complexity of the mechanism, the boiling phenomenon in micro-channels cannot be approached only by experimental and theoretical methods. Therefore, numerical methods should be utilized as well, to supplement these methods. However, most numerical studies have been conducted on macro-channels. In this study, we applied the lattice Boltzmann method, proposed as an alternative numerical tool to simulate the boiling phenomenon in the micro-channel, and predicted the bubble growth process in the channel.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.4
• /
• pp.273-283
• /
• 2008

GDL(Gas Diffusion Layer) is one of the main components of PEM fuel cell. It transports reactants from the channel to the catalyst and removes reaction products from the catalyst to the channels in the flow filed plate. It is known that higher permeability of GDL can make it possible to enhance the gas transport through GDL, leading to better performance. And MEA's temperature is determined by gas and heat transport. In this paper, three dimensional numerical simulation of PEM fuel cell of parallel channel and serpentine channel by the permeability of GDL is presented to analysis heat and mass transfer characteristics using a FLUENT modified to include the electrochemical behavior. Results show that in the case of parallel channel, performance variation with change of permeability of GDL was not so much. This is thought because mass transfer is carried out by diffusion mechanism in parallel channel. Also, in the case of serpentine channel, higher GDL permeability resulted in better performance of PEM fuel cell because of convection flow though GDL. And mass transfer process is changed from convection to diffusion when the permeability becomes low.

• Journal of the Korean Society of Combustion
• /
• v.22 no.2
• /
• pp.50-56
• /
• 2017

This study was conducted an experiment for the thermal flow mechanism of the surrounding butane gas can and pressure change in butane can with oversized cookware. And numerical analysis was performed to analyze the process of heat transfer around butane can. Effect of radiant heat from small size cookware is very small. Thus small size cookware does not have a significant impact on the butane gas range safety. But radiant heat of oversized cookware is larger than small size cookware. Therefore it gives an adverse effect on the butane can. And when internal pressure of butane can is greater than about 406.8~447.2 kPa, a safety device of portable butane gas range were working. The causes of safety device working is because of trivet height. Trivet height is lowered, the radiant heat is increased. This radiant heat is to raise pressure of inside butane can. Experimental and numerical analysis results, the lower thermal conductivity of the cookware is greater the effects of radiant heat.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.5
• /
• pp.581-588
• /
• 2014

Extensive researches toward pool boiling characteristics have been widely investigated. However, the correct understanding of its boiling crisis by Critical Heat Flux (CHF) phenomenon during steady and transient heat transfer as a fundamental database for designing heat generation systems is still need to be clarified. The pool boiling CHFs were investigated to clarify the generalized phenomena of transition to film boiling at transient condition. The CHFs were measured on 1.0 mm diameter horizontal cylinder of platinum for exponential heat generation rates with various periods for saturated liquids at atmospheric pressure. The incipience of boiling processes was completely different depending on pre-pressurization. Also, the dependence of pre-pressure in transient CHFs changed due to the wettability of boiling liquids. The trend of typical CHFs were clearly divided into the first, second and third groups for long, short and intermediate periods, respectively. By the effect of pre-pressurization, the boiling incipience mechanism was replaced from that by active cavities entraining vapor to that by the HSN in originally flooded cavies.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.357-358
• /
• 2014

Coherent anti-Stokes Raman spectroscopy is one of the best tools to measure temperature distributions in the flame. Since it does not disturb the flow field, it could be used to study anchoring mechanism especially in the lifted flame. However, the length of probe volume is, normally, much greater than flame thickness. This weak point was overcome with lens combination in this study. It was found out that no peculiar temperature changes was happened near tribrachial point and heat transfer to the upstream was minimal near the flame anchoring position.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.1
• /
• pp.48-56
• /
• 1984

In order to estimate the fuel rod temperature during the reflooding phase of the PWR LOCA, it is essential to obtain a better understanding of the rewetting mechanism. This paper presents the results of analytical and experimental investigations aimed at analyzing the rewetting phenomena in a heated tube. A two-dimensional solution of the rewetting for a tube is described and used to yield the correlation of the rewetting heat transfer coefficient as the function of flooding rate and inlet subcooling. This correlation prediction is in good agreement with the experimental data.

• Solar Energy
• /
• v.11 no.2
• /
• pp.51-62
• /
• 1991

Heat transfer characteristics for heat retrieving processes in a paraffin-filled horizontal circular cylinder was studied. Theoretical and experimental analyses were carried out. In the theoretical analysis, solid and liquid phases were treated separately. Namely, convection for liquid and conduction for solid phase were investigated respectively. The retrieved heat was calculated from the experimentally determined solidified mass. Furthermore, the effects of initial temperature of the liquid and cooling temperature on the heat discharge rate were also studied. In the heat retrieving process, the governing factor for the solidifying rate is the cooling temperature, because most of the liquid sensible heat is rapidly discharged in the initial stage of solidification. Hence heat transfer mechanism during heat retrieving process can be safely considered as conduction. In the cut of frozen paraffin, there showed an empty space in the upper region. It is caused by the temperature drop in the liquid paraffin. While volume shrinkage caused by phase transition was indiscernible. Irrespective of cooling temperature and initial liquid temperature, solidified mass was well-correlated with the product of Fourier number and Stefan number in the solid phase.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1097-1103
• /
• 2012

There are many fish farms being cultivated in the southwestern cost of South Korea. Because the farms cultivating use the basic method that inflow and circulate sea-water, slight negligence and bad design cause major negative impact on fish deaths. Also, the optimal temperature for each specie of fishes has already been proven to differ on each specie. Maintaining this environment, regardless of seasons, is very difficult and that requires research to develop. In this paper, basic characteristics of heat and mechanism of heat transfer are studied. Based on this, Open-end water vessel is designed and constructed using sandwich-insulation panels and simulated to store the heat in certain isolated space. This study confirmed that it is possible to keep constant temperature by this method, in large areas of water where it is insulated by heat insulator. and equipped with heater in Open-end water vessel where the other part is heated. The AC power controller maintains the constant temperature required and the temperature controller detects and displays the temperature by using the micro-processor.