• Journal of ILASS-Korea
• /
• 제7권2호
• /
• pp.31-36
• /
• 2002

According to the improvement of PC performance, it is expected that calorific value, which causes PC to malfunction, is increased. Therefore, the development of new cooling system is recently required. As the method to solve this problem, we applied loop heat pipe to PC cooling system. The advantage of the loop heat pipe is that it has a small size, light weight, simple shape, long life and it has a good performance on heat transfer, no-noise, wide range of applicable temperature and no supply of power from the outside. It is confirmed that loop heat pipe reduces thermal resistance and has a good performance on PC cooling.

• Microbiology and Biotechnology Letters
• /
• 제27권4호
• /
• pp.278-285
• /
• 1999

In order to use heat shock promoter for the detection of toxic substances, dnaK promoter was amplified from E. coli genomic DNA by using a polymerase chain reaction(PCR) followed by sequencing and sub-cloning into the multi-cloning site of the plasmid, pUCD615. The pUCD615 is a broad-host-range vector containing promoterless lux operon originated from V.fischeri. The recombinant plasmid was transfered to E. coli DH5$\alpha$ through electroporation. The recombinant E. coli showed several patterns of bioluminescent responses to ethanol stress. The bioluminescent E. coli also showed responses to other toxic substances including FeK3(CN)6, CdCl2, p-nitrophenol and HgCl2. The increases of RLU(Relative Light Unit) were observed at 100ppm of FeK3(CN)6, 10ppm and 100ppm and 100ppm of CdCl2, 1ppm of 10ppm of p-nitrophenol and at 1ppm of HgCl2.

• Proceedings of the SAREK Conference
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1167-1171
• /
• 2008

The flow and thermal performance of the skiving and louver fin type heat sinks for the cooling system of the small LED projector were experimentally evaluated. A small fan tester based on AMCA standards was used to control and measure the air flow rate into the heat sink. Three heat blocks were used to simulate the heat and light sources(red, green and blue) of the small LED projector. We measured the pressure drop, temperatures and input power at the specific air flow rate and discussed those results. As a result, it is found that the louver fin type heat sink has higher pressure drop and lower thermal resistance than the skiving type. From the comparison of the temperature of the heat block between skiving and louver fin type, the louver fin type heat sink was found to be more suitable for cooling the high power heat source than skiving type. The thermal performance of the fan-sink(louver fin type) system was discussed with the picture taken by a thermal video.

• Journal of the Optical Society of Korea
• /
• 제15권4호
• /
• pp.362-367
• /
• 2011

Organic ($Alq_3$) film, which was coated on a donor plate, was transferred to an organic light emitting diode (OLED) substrate with help of heat generated by a dithering laser beam. The laser beam was diffracted in an acousto-optic modulator (AOM), then focused on the laser-to-heat converting layer of the donor plate; the focused spot followed trajectories guided by rotation of a Galvano-mirror. Three different functional waveforms, sine wave, square wave, and saw tooth wave were applied to the AOM as modulation signal to generate the dithering beam. The fluorescence microscope images of the donor plate showed that the patterns of removed $Alq_3$ film were affected considerably by the modulation waveforms and the phase difference between adjacent dithering beams. Further, the printed images of Alq3 film on the OLED substrate were different from the patterns of removed Alq3 film. Atomic force microscope images indicated that not only direct transfer but also deposition by sublimated vapor of Alq3 contributed to the pattern formation. Printed patterns affected considerably the electricity-to-light conversion characteristics of OLEDs. For uniform transfer, not only the phase relation of dithering beam lines but also adequate waveform were important.

• ETRI Journal
• /
• 제45권3호
• /
• pp.519-533
• /
• 2023

This paper implements a simultaneous solar and thermal energy harvesting system, as a hybrid energy harvesting (HEH) system, to convert ambient light into electrical energy through photovoltaic (PV) cells and heat absorbed in the body of PV cells. Indeed, a solar panel equipped with serially connected thermoelectric generators not only converts the incoming light into electricity but also takes advantage of heat emanating from the light. In a conventional HEH system, the diode block is used to provide the path for the input source with the highest value. In this scheme, at each time, only one source can be handled to generate its output, while other sources are blocked. To handle this challenge of combining resources in HEH systems, this paper proposes a method for collecting all incoming energies and conveying its summation to the load via the current mirror cells in an approach similar to the maximum power point tracking. This technique is implemented using off-the-shelf components. The measurement results show that the proposed method is a realistic approach for supplying electrical energy to wireless sensor nodes and low-power electronics.

• KIEAE Journal
• /
• 제14권6호
• /
• pp.81-86
• /
• 2014

In recent years, many researchers have considered the building energy consumption reduction accordingly to deal with abnormal climate changes and greenhouse gas reduction. However, the lighting energy use ratio has increased in spite of the development of the high efficiency lighting device. Therefore, the study aims to produce the LED lighting applications for the effective lighting heat removal by using the heat characteristics of LED lighting and analyzing the heat removal effect. In order to increase radiant heat efficiency, the heat pipe and heat sink was attached on PCB as LED lighting applications. Experiment was conducted to verify the temperature and air velocity of inside duct: thermocouples, anemometer. The heat removal effect of LED lighting applications was measured by observing the temperature of the lighting applications and the change of air velocity in duct. The experiment shows that the temperature change in the duct according to air velocity was $0.9{\sim}5.8^{\circ}C$. It is also concluded that heat removal was calculated from 33 to 81W.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• 제17권3호
• /
• pp.108-112
• /
• 2007

Cubic Zirconia single crystals having changeable color with light source were grown by skull melting method. Strong absorption of yellow color region light by Co and Nd and the absorption in violet color region by Fe led the color change from blue-green to red-purple with the light source from fluorescent to incandescent lamp. Color of crystals varied not only by the dopants but yttria contents and the conditions far heat treatment.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.122-124
• /
• 2005

The flat panel lamp is used as back light. It is perceived the best type for the wide size LCD of back light system. However, the flat panel lamp has high value of heat. So it need to improve efficiency. Therefore, more researches are requested for the back light of the flat panel lamp. In this paper, the properties of spectrum is investigated according to change in frequency from 30kHz to 60kHz using power supplies voltage with changing from 500V to 700V. As a result, main spectrum peak of plasma showed in 450[nm], 630[nm], 750[nm] and spectrum peak of 750nm is the highest.

• Nuclear Engineering and Technology
• /
• 제39권4호
• /
• pp.249-256
• /
• 2007

Light water reactors operated under supercritical pressure conditions have been selected as one of the promising future reactor concepts to be studied by the Generation IV International Forum. Whereas the steam cycle of such reactors can be derived from modem fossil fired power plants, the reactor itself, and in particular the reactor core, still need to be developed. Different core design concepts shall be described here to outline the strategy. A first option for near future applications is a pressurized water reactor with $380^{\circ}C$ core exit temperature, having a closed primary loop and achieving 2% pts. higher net efficiency and 24% higher specific turbine power than latest pressurized water reactors. More efficiency and turbine power can be gained from core exit temperatures around $500^{\circ}C$, which require a multi step heat up process in the core with intermediate coolant mixing, achieving up to 44% net efficiency. The paper summarizes different core and assembly design approaches which have been studied recently for such High Performance Light Water Reactors.

• Proceedings of the SCSK Conference
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book I
• /
• pp.61-72
• /
• 2003

In cosmetic area, retinol is prominent ingredient for anti-wrinkle but unstable against light, heat, oxygen and so on. Therefore the stabilization of retinol is required. Here, we capsulated doubly retinol in the SLM(Skin Lipid Matrix) that makes three dimensional lamellar structure similar to skin, after formation of primary liposome (retinol-nanoemulsion). First, we make primary liposome from retinol / hydrogenated lecithin / polysorbate20 / caprylic ＆ capric triglyceride / ethanol / and so on, and the mean diameter to 70 nm, using microfluidizer passed three times at 800 Bar, repeatedly. Then we produce DC-liposome (doubly capsulated-liposome) that was encapsulated primary liposome with SLM made of hydrogenated phosphatidyl choline / caprylic ＆ capric triglyceride / 1, 3-butylene glycol / ceramide3 / cholesterol /etc. We measured for color stability against light and heat with chromameter. As a result of this experiment, we observed DC-liposome was more than from 1.5 to 3 times as stable as general liposome. Livability of retinol has improved from 2 to 6 times when we analyzed it by HPLC. Also, penetration effect of DC-liposome has improved.