• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1595-1602
• /
• 1992

An energy efficient drying system, utilizing a heat pump to recover the wasted heat with high efficiency is proposed. In conventional drying systems, over-heating occurs through a condenser as the same amount of air is provided into the evaportator and the condenser. In order to prevent the over-heating, part of the outlet air from the drying chamber must be bypassed to increase the rate of vaporization in the drying chamber without release of the heat from the system. Since a part of the heat in the condenser is used to heat the air during the drying process of the proposed system, a high drying efficiency and low SPC(Specific Power Consumption) could be obtained, Comparing the performances between the proposed heat pump and a conventional one, it was found that the drying efficiency of the proposed heat pump is higher than that of the conventional heat pump by an amount of 7-25%.

• Journal of Bio-Environment Control
• /
• v.27 no.4
• /
• pp.356-362
• /
• 2018

Hot pepper is a kind of seasoning vegetables, which is a major item in the Korean vegetable market. Since the use of hot pepper is processed into pepper powder, which is a powder form of dried hot pepper, improvement of quality and productivity of dried hot pepper is important. Therefore, this experiment was conducted to suggest proper drying method by comparing the changes of hot pepper powder ingredients considering production cost according to the drying method. As a drying method, we used sun drying and heat drying which are widely used in practice. We also compared the productivity and quality of dried hot pepper by applying a dehumidifying drying method using a dehumidifier. Drying rate of hot pepper was highest of 85.1% at heat drying. Accordingly moisture content of hot pepper powder was lowest of 13.5% at heat drying. The American Spice Trade Association (ASTA) color value, which influenced the coloring of red pepper, showed higher in heat drying and dehumidified drying treatment than the sun drying treatment. The content of capsaicinoids was higher at sun drying treatment than that of at both heat drying and dehumidified drying treatments. The content of sugar was higher at heat drying and dehumidified drying treatment where drying time was relatively short than that of sun drying treatment. Also, there was no significant difference in sugar content between the two treatments. The production cost of dried hot pepper with dehumidified drying was 9.9% more efficient than heat drying. Through this study, it was found that heat and dehumidified drying method were effective in increasing sugar content and coloring of hot pepper powder. In order to improve the capsaicinoid content of red pepper, it is considered that appropriate drying temperature and drying time should be added in the process of heat drying and dehumidified drying.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.2
• /
• pp.103-108
• /
• 2003

This study was performed to find out drying characteristics and develop waste heat recovery dryer. this system was initiated in order to recover discharged waste heat of drying air from drying chamber in agricultural products dryer and recycle for additional heat source that could save drying cost. The system consists of drying chamber, fan, burner, circulation pump and heat exchanger made of fins and tubes. For the system performance, drying experiments with fresh pepper were conducted, and comparisons on fuel consumption amount and drying performance were made between conventional dryer and the heat recovery system attached dryer.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.10
• /
• pp.860-867
• /
• 2007

Heat pump drying has a great potential for energy saving due to its high energy efficiency in comparison with conventional air drying. In the present study, the performance simulation for the basic design of a heat pump dryer has been carried out. The simulation includes one-stage heat pump cycle, simple drying process using the drying efficiency. As an example, the heat pump cycle with Refrigerant 134a has been investigated. For the operating conditions such as the average temperature of the condenser, the heat rate released in the condenser, the flow rate of drying air, and drying efficiency, the simulation has been carried out to figure out the performance of the dryer. The parameters considered in the design of the dryer are COP, MER, SMER, the rate of dehumidification, the temperature and humidity of drying air and those parameters are compared for different conditions after carrying out the simulation.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.636-641
• /
• 2008

Heat pump drying has a great potential for energy saving due to its high energy efficiency in comparison to conventional air drying. The heat pump dryer is usually operated at the temperature less than $50^{\circ}C$ and the drying temperature is limited to the operating temperature of the heat pump system. In order to increase the drying temperature, the special box-type heat pump dryer has been developed. The dryer uses the two-cycle heat pump system which has the two heat pump cycles for high and low temperature heating. The high temperature cycle uses the refrigerant 124 to get the temperature greater than $80^{\circ}C$ and the low temperature cycle uses the refrigerant 134a. The drying experiment has been carried out to figure out the performance of the dryer with the selected drying material.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.15 no.4
• /
• pp.362-371
• /
• 1986

In the normal Refrigeration process, the condensation heat of refrigerant s not been used because of its low-temperature waste heat. To recover the condensation waste heat of R-12 refrigerator, a drying and hot water system was designed and experimented. The results obtained were summarized as follows: 1. As the temperature a temosphere was increased, the temperature of discharge gas of compressor was increased. And the temperature was $80-84^{\circ}C$ for air condensing type and was $68-71^{\circ}C$ for water condensing type during summer. 2. The condensation waste heat could be obtained up to $50-55^{\circ}C$ of drying heat-source and Hot water in summer. In this case, recovered rate was about $73\%$. And the more temperature of drying Heat-source and Hot water were increased, the more a recovered rate were decreased. 3. When comparing drying characteristics of Agro-products in dryer of waste heat utilization and Hot air, there was no quality difference in products. But drying time of the former was 3 Hours longer than the latter. 4. The condensation waste heat of compressor could be applied into the drying of marine products, the predrying of agro-products and making hot water. And showed high possibility of the waste heat using in low-temperature storage.

• Journal of Korea Foresty Energy
• /
• v.21 no.3
• /
• pp.10-17
• /
• 2002

This study was carried out to investigate a heat treatment condition and suitable drying schedule of bamboo material(Phyllostachys nigra var. henonis) for a vertical flute with small-notched bamboo. It is very important to prevent drying defects during its drying process. We investigated the effort of heat treatment the most suitable drying schedule for small-notched bamboo vertical flute without drying defects in this research. A direct heat treatment method and drying conditions of 3($20^{\circ}C$ 65%, $40^{\circ}C$ 40%, and dry at air condition) were applied to the Bamboo specimen that felled in several areas for a month. The result suggested that the most suitable drying schedule with the less split and the shortest time was to dry at $40^{\circ}C$, 40% condition and it was useful to direct heat-treatment because of reducing the number and size of split during drying bamboo.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.44-48
• /
• 2021

Semiconductor inspection equipment makes components using materials with insulating properties for functional inspection including current and voltage of semiconductor parts. A representative insulating material is plastic, and plastic is made of a component through an injection process using plastic pellet. When plastic pellets contain excessive moisture, problems such as performance degradation and product surface defects occur. To prevent this, pre-drying is essential, and the heat convective type is the most applied. However, the heat convective type has a problem of low consumption efficiency and a long drying time. Recently, many studies have been conducted on a drying method using microwaves due to high energy efficiency. In this paper, drying was performed using a microwave for drying PC pellets. Energy consumption and drying efficiency analyzed by set up an experimental apparatus of heat convective, microwave, and hybrid(heat convective + microwave) types. It was confirmed that energy consumption and drying efficiency were high when drying using microwaves, and it was confirmed that the hybrid method improved drying performance compared to the heat convective method. It is expected that the research results of this paper can be used as basic data for drying plastic pellets using microwave.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2009

The simulation of a heat pump dryer has been carried out to figure out the effect of air flow rate on the drying performance represented by MER, SMER, and so on. The simulation includes the analyses of one-stage heat pump cycle and simple drying process using the drying efficiency. The heat pump cycle with Refrigerant 134a has been considered. In the dryer, some of drying air from the drying chamber flows through the heat pump system, the rest of air bypasses the heat pump system. The two air flows joins before the drying chamber inlet. The performance parameters considered in the present study are MER, SMER, the temperature and humidity of drying air. Those parameters are compared for different total air flow rate or bypass air flow rate.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2268-2273
• /
• 2008

The drying model has been used to obtain the fundamental information required to design the heat pump dryer with the simple thermodynamic model. In the model, the input conditions are crucial to obtain the acceptable results. The model includes one-stage heat pump cycle, simple drying process using the drying efficiency. The drying efficiency is defined with the conditions of inlet and outlet in the dryer. The experiment has been carried out in the pilot dryer with one-stage heat pump cycle. Refrigerant 134a is used in the heat pump cycle. In the dryer, some of drying air flows through the heat pump system and the rest of air bypasses the heat pump system and circulates through the drying chamber. Some operating conditions from the pilot dryer are used as input conditions of the model and the results are compared with experimental results for the validation.