• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.664-675
• /
• 1990

In this study, the performance test and heat transfer experiment for a 4 cylinder and 4-cycle turbocharged gasoline engine were carried out in order to measure the heat transfer coefficient at the inner wall of the combustion chamber. From the result of heat transfer experiment, the energy balance of the fuel energy and the overall efficiency of the turbocharger were calculated, The variation of them was investigated as well with the engine operation conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1372-1380
• /
• 1988

A heat transfer model for a pulse combustion water heater is developed, and an associated computer simulation is conducted to determine the temperature distribution as well as heat transfer rate. Parametric studies are performed to examine the effects of the operating and design variables on the thermal performance and heat transfer rate. They are found to be influenced mainly by energy input rate, the amount of excess air, the volume of combustion chamber, and the diameter of flue tube.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.123-123
• /
• 1994

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.5
• /
• pp.435-441
• /
• 2011

The life cycle assessment on greenhouse gas emission of reinforced concrete buildings shows that more than 70 percent of greenhouse gas that is discharged by a building is discharged in the building maintenance stage, including cooling and heating. To reduce the greenhouse gas emission, maintenance planning to minimize the energy consumption is necessary in the design stage. In this paper, two heat storage rooms are tested to save the air cooling energy of the buildings. The specimens are essentially identical, except that chamber A contained paraffin sheets as the finishing material, while the other, chamber B, served as a control. The test results show that chamber A with the paraffin sheets exhibited less temperature change than chamber B without the sheets when temperature was increased outside of the specimens. The heating energy was probably consumed in the phase change of the paraffin sheets, which can be useful for reducing energy consumption related to air cooling during the summer.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.24 no.5
• /
• pp.727-736
• /
• 2010

This study is about researching mechanistic pattern identification of disease for DongEuiBoGam NaeGyungPyen by analysing with pattern identification of modern Traditional Korean medical patholgy as more logical, systematic and standardized theory. Disease pattern mechanisms of uterine, urine and excrements parts of DongEuiBoGam NaeGyun gPyen in NaeGyungPyen of DongEuiBoGam are these. Menstrual irregularities in DongEuiBoGam can be classified flui d-humor depletion, blood deficiency, qi deficiency, qi stagnation, qi stagnation complicated by heat, blood stasis, blood deficiency complicated by heat, syndrome of heat entering blood chamber, syndrome of cold entering blood chamber. The disease pattern of abdominal pain after menstruation in DongEuiBoGam is blood deficiency complicated by heat, and a dysmenorrhea represents blood stasis with heat, fluid-humor deficiency. Advanced menstruation represent dual heat of the qi and blood, delayed menstruation is blood deficiency. The disease pattern of inhibited urination in DongEuiBoGam can be classified deficiency heat pattern of kidney yin deficiency(yin deficiency with effulgent fire), kidney qi deficiency, yin deficiency with yang hyperactivity, fluid-humor depletion, spleen-stomach dual deficiency, and excess he at pattern of bladder excess heat. The disease pattern of urinary incontinence in DongEuiBoGam can be classified deficiency pattern of kidney-bladder qi deficiency, consumptive disease, lung qi deficiency, kidney yin deficiency(yin deficiency with effulgent fire), kidney yang deficiency and excess pattern of lower energizer blood amassment, bladder excess heat. And most of them are deficiency from deficiency-excess Pattern Identification. The disease pattern of diarrhea in DongEuiBoGam can be classified deficiency pattern of qi deficiency, qi fall, spleen yang deficiency, kidney yang deficiency and so on and excess pattern of wind-cold-summerheat-dampness-fire, phlegm-fluid retention, dietary irregularities, qi movement stagnation. And most of them are deficiency from deficiency-excess Pattern Identification. Like these, this study identify pattern of disease in DongEuiBoGam by mechanism of disease theory.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.3
• /
• pp.138-152
• /
• 1996

Many studies of heat transfer on the swirling flow or unswirled flow in a abrupt pipe expansion are widely carried out. The mechanism is not fully found evidently due to the instabilities of flow in a sudden change of the shape and appearance of turbulent shear layers in a recirculation region and secondary vortex near the corner. The purpose of this study is to obtain data through an experimental study of the swirling flow and heat transfer downstream of an abrupt expansion in a circular pipe with uniform heat flux. Experiments were carried out for the turbulent flow nd heat transfer downstream of an abrupt circular pipe expansion. The uniform heat flux condition was imposed to the downstream of the abrupt expansion by using an electrically heated pipe. Experimental data are presented for local heat transfer rates and local axial velocities in the tube downstream of an abrupt 3:1 & 2:1 expansion. Air was used as the working fluid in the upstream tube, the Reynolds number was varied from 60, 00 to 120, 000 and the swirl number range (based on the swirl chamber geometry, i.e. L/d ratio) in which the experiments were conducted were L/d=0, 8 and 16. Axial velocity increased rapidly at r/R=0.35 in the abrupt concentric expansion turbulent flow through the test tube in unswirled flow. It showed that with increasing axial distance the highest axial velocities move toward the tube wall in the case of the swirling flow abrupt expansion. A uniform wall heat flux boundary condition was employed, which resulted in wall-to-bulk temperatures ranging from 24.deg. C to 71.deg. C. In swirling flow, the wall temperature showed a greater increase at L/d=16 than any other L/d. The bulk temperature showed a minimum value at the pipe inlet, it also exhibited a linear increase with axial distance along the pipe. As swirl intensity increased, the location of peak Nu numbers was observed to shift from 4 to 1 step heights downstream of the expansion. This upstream movement of the maximum Nusselt number was accompanied by an increase in its magnitude from 2.2 to 8.8 times larger than fully developed tube flow values.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.210-216
• /
• 1999

The objective of this paper is to investigate corrosion behaviors of CoCrTa/CrNi thin film and post heat-treatment effect. An electron beam evaporator was used for films deposition. After evaporation, post heat-treatment was carried out under $5.0{\times}10^3$ Torr vacuum condition. Annealing temperature and time were 400 $^{\circ}C$ and 30 min, respectively. To understand the effect of annealing on corrosion behavior of CoCrTa/CrNi, potentiodynamic polarization technique and accelerated corrosion chamber test were undertaken. Corrosion potential is higher for the annealed samples (CoCrTa 400$\AA$/CrNi 1000$\AA$) than for as-deposited one. This is attributed to an enrichment of Cr in the surface layer of the thinfilm resulting in a more corrosion resistant material.

• Journal of the Korean Society of Combustion
• /
• v.10 no.1
• /
• pp.20-26
• /
• 2005

In the present study, catalytic combustion of hydrogen-air premixture in a millimeter scale monolith coated with Pt catalyst was investigated. As the combustor size decreases, the heat loss increases in proportion with the inverse of the scale of combustion chamber and combustion efficiency decreases in a conventional type of combustor. Combustion reaction assisted by catalyst can reduce the heat loss by decreasing the reaction temperature at which catalytic conversion takes place. Another advantage of catalytic combustion is that ignition is not required. Platinum was coated by incipient wetness method on a millimeter scale monolith with cell size of $1{\times}1mm$. Using this monolith as the core of the reaction chamber, temperatures were recorded at various locations along the flow direction. Burnt gas was passed to a gas chromatography system to measure the hydrogen content after the reaction. The measurements were made at various volume flow rate of the fuel-air premixture. The gas chromatography results showed the reaction was complete at all the test conditions and the reacting species penetrated the laminar boundary layer at the honeycomb and made contact with the catalyst coated surface. At all the measuring locations, the record showed monotonous increase of temperature during the measurement duration. And the temperature profile showed that the peak temperature is reached at the point nearest to the gas inlet and decreasing temperature along the flow direction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.78-82
• /
• 2003

The cooling mechanism for a regenerative cooling liquid rocket engine of 10tf-thrust using kerosene as a fuel was studied from the viewpoint of curtain cooling. Based on the concept of a highly-stratified gas flow in the combustion chamber, the cross section of the combustion chamber was spilt into 2 independent parts, core and exterior part. Additional fuel is injected into the exterior section and gas temperature can be reduced in the exterior section. Consequently, the heat flux into the coolant and wall temperature are reduced and the thermal stability of a liquid rocket engine could be improved.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.3
• /
• pp.219-228
• /
• 2003

Numerical and experimental studies were conducted on the temperature distribution of a buried steel pipe and surrounding granite frozen soils in the closed system. The relationship between unfrozen water content and temperatures was analysed by laboratory test. The thermal conductivity measurements were made to compare the results with a formula presented by Lachenbruch. A steel container model that consists of a freezing chamber and a buried circular steel pipe was built for the laboratory temperature measurements. The time temperature records were measured experimentally, and those records were compared with numerical results obtained from FEM analysis in order to verify the feasibility. The latent heat effect on the granite frozen soils in the numerical study was considered.