• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.6.2-6.2
• /
• 2010

Stainless steel is widely known to have superior corrosion properties. However, in some harsh conditions it still suffers various kinds of corrosions such as galvanic corrosion, pitting corrosion, intergranular corrosion, chloride stress corrosion cracking, and etc. For the corrosion protection of stainless steel, the ceramic coatings such as protective silica film can be used. The sol-gel coating technique for the silica film has been extensively studied especially because of the cost effectiveness. It has been proved that silica can improve the oxidation and the acidic corrosion resistance of metal surface in a wide range of temperatures due to its high heat and chemical resistance. However, in the sol-gel coating process there used to engage a heat treatment at an elevated temperature like $500^{\circ}C{\sim}600^{\circ}C$ where cracks in the silica film would be formed because of the thermal expansion mismatch with the metal. The cracks and pores of the film would deteriorate the corrosion resistance. When the heat treatment temperature is reduced while keeping the adhesion and the density of the film, it could possibly give the enhanced corrosion resistance. In this respect, inorganic protective silica film was tried on the surface of stainless steel using a sol-gel chemical route where silica nanoparticles, tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) were used. Silica nanoparticles with different sizes were mixed and then the film was deposited on the stainless steel substrate. It was intended by mixing the small and the large particles at the same time a sufficient consolidation of the film is possible because of the high surface activity of the small nanoparticles and a modest silica film is obtained with a low temperature heat treatment at as low as $200^{\circ}C$. The prepared film showed enhanced adhesion when compared with a silica film without nanoparticle addition. The films also showed improved protect ability against corrosion.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.83-84
• /
• 2017

The heat treatment performed during the welding of the structure should adjust the temperature of the structure in several steps in order to further improve the welding performance. This paper proposes a technique to control multiple SCR power converters to control the temperature of each ceramic heater at various stages according to a specified time.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.141-146
• /
• 2002

The cast iron cylinder liner of the marine engine must be scrapped after its inner surface was definitely worn out due to the friction between the surface and piston ring during the operating. In this research, the restoring method of the worn out cast iron cylinder liner are discussed based on the results of experimental work of the thermal plastic deformation technique.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.267-276
• /
• 2019

The purpose of this study was to examine the influence of conditions for quenching and/or tempering on the corrosion and hydrogen diffusion behavior of ultra-strong automotive steel in terms of the localized plastic strain related to the dislocation density, and the precipitation of iron carbide. In this study, a range of analytical and experimental methods were deployed, such as field emission-scanning electron microscopy, electron back scatter diffraction, electrochemical permeation technique, slow-strain rate test (SSRT), and electrochemical polarization test. The results showed that the hydrogen diffusion parameters involving the diffusion kinetics and hydrogen solubility, obtained from the permeation experiment, could not be directly indicative of the resistance to hydrogen embrittlement (HE) occurring under the condition with low hydrogen concentration. The SSRT results showed that the partitioning process, leading to decrease in localized plastic strain and dislocation density in the sample, results in a high resistance to HE-induced by aqueous corrosion. Conversely, coarse iron carbide, precipitated during heat treatment, weakened the long-term corrosion resistance. This can also be a controlling factor for the development of ultra-strong steel with superior corrosion and HE resistance.

• Animal cells and systems
• /
• v.13 no.3
• /
• pp.267-274
• /
• 2009

The dissociative culture technique of Aplysia neuron is one of the key methods that have been used for studies of cellular and molecular mechanisms of neuronal functioning. However, despite the advantages this method offers as an experimental model, its technical efficiency has had room for improvement. In this study, we examined certain putative factors that might affect the culture quality. The effects of neuronal damage induced by physical injuries, heat shock, and surface protein degradation were evaluated along with the correlation between the culture quality and animal behavior. As a result, we found that physical injury can be a critical factor that affects culture quality, whereas the heat shock and surface protein degradation had negligible effect on it. In addition, we discovered that siphon retraction time was not a good measurement for healthy neurons. Based on these findings, we suggest here an improved method in which the degree of physical injury is reduced by means of multiple protease treatment.

• The Korean Journal of Ceramics
• /
• v.3 no.2
• /
• pp.110-115
• /
• 1997

Li-doped ZnO films were prepared on Corning 1737 glass substrate by an rf magnetron sputtering technique using ZnO targets with various $Li_2CO_3$ contents ranging from 0 to 10 mol%. The effects of Li doping on the crystallinity and electrical properties of ZnO films were studied for their SAW filter applications. The film resistivity largely increased without suppressing the c-axis orientation and crystallinity with a small addition of Li. Heat treatment of the film at 40$0^{\circ}C$ induced that the film resistivity, c-axis orientation and crystallinity slightly increased. However, heat treatment of the film at 50$0^{\circ}C$ resulted in much lower resistivity than that of as-deposited film due to the increase of electron concentration caused by the evaporationof Li atoms from the ZnO film. Large addition of Li into the ZnO film rather diminished the film resistivity and suppressed the c-axis growth. It was concluded that a small doping of Li into the ZnO film and heat treatment at 40$0^{\circ}C$ caused the film resistivity to be high enough for SAW filter applications without suppression of the c-axis orientation and crystallinity.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.2
• /
• pp.147-158
• /
• 1996

Generally, analytical consideration on the behaviour of metallic structures during quenching process, and analysis on the thermal stress and deformation after heat treatment are very important in presumption of crack and distorsion of quenched material. In this study a set of constitute equations relevant to the analysis of thermo elasto-viscoplastic materials with strain hysteresis during quenching process way presented on the basis of contimuum thermo-dynamics mechanics. The thermal stresses were numerically calculated by finite element technique of weighted residual method and the principle of virtual work. In the calculation process, the temperature depandency of physical and mechaniclal properties of the material in consideration. On the distribution of elasto-viscoplastic thermal stresses according to radial direction, axial and tangential stress are tensile stress(50MPa, 1.5GPa and 300MPa) in surface and compressive stress(-1.2GPa, -1.14GPa and -750MPa) in the inner part on the other hand, radial stress is tensile stress(900MPa) in area of analysis. According to axial direction, tangential stress gradients are average 60MPa/mm on the whole. The reversion of stress takes place at 11.5 to 16.8mm from the center in area of analysing.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.6
• /
• pp.575-580
• /
• 1986

Triploid rainbow trout (Salmo gairdneri) were produced on a large scale practice by the application of moderate heat treatment in 1986. Triploid treatment of the fertilized eggs was carried out with heat shock at $27^{\circ}C$ for 10 to 14 minutes starting 10 minutes after insemination at $10^{\circ}C$. Estimated triploidy ranged from $45\%\;to\;57\%$ ana the incidence of triploidy slightly increased with the treatment time. No significant differences of growth rate were observed between triploidy and diploidy at the early stage of growth. This observation was consistent with results of other fish species and other reports on this species. This heat shock technique, expecting further improvement, should be useful in the mass production of sterile triploid rainbow trout.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.68-73
• /
• 1999

In this paper, the residual stresses for the wide-band laser heat treatment using a polygon mirror have been analyzed. The results of FE analysis are compared with the experimental results. ANSYS Version 5.3, a commercial FE-code, is used for the FE stress analysis. The structural analysis was performed on after thermal analysis. The residual stress distribution across the hardened area was measured by the X-ray diffraction technique. The laser hardening conditions, 2kW laser power and 2mm/s travel speed, were used for the experiment and the FE analysis. Analysis results, which is maximum tensile residual stress is about 143MPa and maximum compressive residual stress is about -380MPa. Under same parameters with the analysis, experimental results indicate that MTRS is about 152MPa and MCRS is about -312MPa. The experimental results is about 6% higher than the FE analysis. As a result, residual stress data from the experiment close well with that of the FE analysis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.11
• /
• pp.1559-1567
• /
• 2012

The objective of this study was to evaluate ruminal degradability and intestinal digestibility of crude protein (CP) and amino acids (AA) in hempseed cake (HC) that were moist heat treated at different temperatures. Samples of cold-pressed HC were autoclaved for 30 min at 110, 120 or $130^{\circ}C$, and a sample of untreated HC was used as the control. Ruminal degradability of CP was estimated, using the in situ Dacron bag technique; intestinal CP digestibility was estimated for the 16 h in situ residue using a three-step in vitro procedure. AA content was determined for the HC samples (heat treated and untreated) of the intact feed, the 16 h in situ residue and the residue after the three-step procedure. There was a linear increase in RUP (p = 0.001) and intestinal digestibility of RUP (p = 0.003) with increasing temperature during heat treatment. The $130^{\circ}C$ treatment increased RUP from 259 to 629 g/kg CP, while intestinal digestibility increased from 176 to 730 g/kg RUP, compared to the control. Hence, the intestinal available dietary CP increased more than eight times. Increasing temperatures during heat treatment resulted in linear decreases in ruminal degradability of total AA (p = 0.006) and individual AA (p<0.05) and an increase in intestinal digestibility that could be explained both by a linear and a quadratic model for total AA and most individual AA (p<0.05). The $130^{\circ}C$ treatment decreased ruminal degradability of total AA from 837 to 471 g/kg, while intestinal digestibility increased from 267 to 813 g/kg of rumen undegradable AA, compared with the control. There were differences between ruminal AA degradability and between intestinal AA digestibility within all individual HC treatments (p<0.001). It is concluded that moist heat treatment at $130^{\circ}C$ did not overprotect the CP of HC and could be used to shift the site of CP and AA digestion from the rumen to the small intestine. This may increase the value of HC as a protein supplement for ruminants.