• Tribology and Lubricants
• /
• 제33권3호
• /
• pp.85-91
• /
• 2017

This work studies the flow behaviors in the gap between the friction pad and separator in wet-clutch systems. The fluid volume of the lubricant is modeled using the entire system of wet-clutch pack of a dual clutch transmission that has larger outer radius of odd gear shifts and smaller inner radius of even gear shifts. Flow behaviors in the gap of the clutch pad are computed using the gear shift modes that consider the real relative velocities between the friction pad and separator. Flow behaviors in the gap of the disengaged clutch pad are mainly investigated for the wet-clutch system, whereas the engaged clutch pad is modeled with no fluid rate through the contacting surfaces. The developed hydrodynamic fluid pressures and velocity fields in the clutch pad gap are computed to obtain the relevant information for managing flow rates in wet-clutch packs under dual operating conditions during gear shifts. These hydrodynamic pressures and velocity fields are compared on the basis of each gear level and gap location, which is necessary to determine the effects of groove patterns on the friction pad. Shear stresses in the gap locations are also computed on the basis of the gear level for the inner and outer clutch pads. The computed results are compared and used for the design of cooling capacity against frictional heat generation in wet-clutch pack systems.

• 대한전기학회논문지:전력기술부문A
• /
• 제55권10호
• /
• pp.426-432
• /
• 2006

This paper describes the concepts of Static Line Rating (SLR) and Dynamic Line Rating (DLR) and the computational methods to demonstrate them. Calculation of the line capacity needs the heat balance equation which is also used for computing the reduced tension in terms of line aging. SLR is calculated with the data from the worst condition of weather throughout the year. Even now, the utilization ratio is obtained from this SLR data in Korea. DLR is the improved method compared to SLR. A process for DLR reveals not only improved line ratings but also more accurate allowed line ratings based on line aging and real time conditions of weather. In order to reflect overhead transmission line aging in DLR, this paper proposes the method that considers the amount of decreased tension since the lines have been installed. Therefore, the continuous allowed temperature for remaining life time is newly acquired. In order to forecast DLR, this paper uses weather forecast models, and applies the concept of Thermal Overload Risk Probability (TORP). Then, the new concept of Dynamic Utilization Ratio (DUR) is defined, replacing Static Utilization Ratio (SUR). For the case study, the two main transmission lines which are responsible for the north bound power flow in the Seoul metropolitan area are chosen for computing line rating and utilization ratio. And then line rating and utilization ratio are analyzed for each transmission line, so that comparison of the present and estimated utilization ratios becomes available. Finally, this paper proves the validity of predictive DUR as the objective index, with simulations of emergency state caused by system outages, overload and so on.

• 전기학회논문지
• /
• 제66권12호
• /
• pp.1844-1851
• /
• 2017

As the capacity of the wireless power transmission increases, a higher supply current which may induce current in nearby conductive parts requires. Induced current may affect electric shock to the human body and malfunction of the electrical equipment. In order to prevent such induced phenomena as a risk factor, shielding is required between the source of the wireless power transmission and the conductive parts. The resonance frequency for the large capacity wireless power transmission has the wavelength of several hundred meters, so most environments are included in the near-field area. By wave impedance, the electric field has higher density in the near-field area and needs to be analyze for protecting. For this purpose, it is necessary to select a substance having a larger electric conductivity and optimized shielding structure. In this paper, an aluminum base shielding structure was presented to conduct experiments on thickness, position, and heat dissipation. In the 35 kW, 60 kHz environments, the optimized 5T Al base shielding structure attenuates the induced current to 43 %.

• 한국의류학회지
• /
• 제41권1호
• /
• pp.84-97
• /
• 2017

Water vapor and thermal transmission properties of high emotional garments are important to evaluate wear comfort; in addition, the measuring methods of these properties are also critical for breathable and warm suit fabrics. In this study, the water vapor and thermal properties of composite yarn fabrics made of CoolMax, Tencel, and Bamboo fibers with filaments were measured and compared according to the measuring method. Water Vapor Transmittance (WVT) of the fabric woven by the sheath/core composite yarn in the warp direction was the highest due to the small staple fiber volume in the sheath/core yarn structure and high air voids in the sheath/core yarn fabrics. This property was also the highest in fabrics woven by bamboo staple yarns in the weft direction, and was the lowest on hi-multi filament fabrics. However, water vapor resistance ($R_{ef}$) of these fabrics by KSK ISO 11092 showed the opposite results to the water vapor transmittance method ($CaCl_2$ method); in addition, its correlation coefficient was low. The correlation coefficient between $R_{ef}$ and the drying rate was 0.719; therefore, the measurement mechanism of $R_{ef}$ is analogous to the drying property measurement. The thermal conductivity of the fabrics woven with compact staple yarn showed a high value; however, the hi-multi filament fabric showed low thermal conductivity. Therefore, fiber characteristics affect thermal properties more than yarn structure. The correlation between thermal property and moisture transport was also low. This study showed that: water vapor transmittance was active at the loose yarn structure, dry heat transport was vigorous at the compact yarn structure, and heat transport was affected more by fiber characteristics than yarn structure. In conclusion, sheath/core composite yarns were relevant to the high absorptive cool suit along with siro-fil and CoolMax/Bamboo staple yarns that were relevant to the heat diffusive cool suit.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.8-13
• /
• 2015

This study was carried out to evaluate mechanical properties of the jointed Al6061/HT590 alloys by friction stir welding (FSW). FSW was conducted under the conditions with tool rotating speed of 500 RPM and traveling speed of 300 mm/min., where Ar gas was introduced to prevent the materials from corrosion during the welding process. Electron back-scattering diffraction (EBSD) was used to characterize microstructures such as grain size, misorientation angle and crystal orientation. Evolution of intermetallic compounds in Al6061 during the process were examined in terms of morphology, size and aspect ratio at three distinct zones Al base material, heat affected zone and stir zone, where transmission electron microscope (TEM) was used. It was revealed that FSW gave rise to refinement of grains as well as growth of intermetallic compounds in Al6061. The morphological changes of intermetallic compounds exerted an influence on mechanical properties, resulting in occurrence of fracture in the part of the base material instead of the jointed parts (heat affected zone and stir zone). This study systematically evaluated the microstructural evolutions during the FSW for joining Al6061 with HT590 and their effect on mechanical properties.

• 한국농촌건축학회논문집
• /
• 제20권1호
• /
• pp.11-18
• /
• 2018

The study aims to address the energy crisis and realize self-sufficiency of building as part of local energy independence, breaking away from a single concentrated energy supply system. It is intended to develop modules of the outside insulation composite panels that conform to passive certification criteria and for site-assembly systematization. The method of study first identifies trends and passive house in literature and advanced research. Second, the target performance for development is set, and the structural material is selected and designed to simulate performance. Third, a test specimen of the passive outside insulation curtain wall module designed is manufactured and constructed to test its heat transmission coefficient, condensation performance and airtightness. Finally, analyze performance test results, and explore and propose ways to improve the estimation and improvement of incomplete causes to achieve the goal. The final test results achieved the target performance of condensation and airtightness, and the heat transmission coefficient was $0.16W/(m^2{\cdot}K)$, which is $0.01W/(m^2{\cdot})K$ below the performance target. As for the lack of performance, we saw a need for a complementary design to account for simulation errors. It also provided an opportunity to recognize that insulated walls with performance can impact performance at small break. Thus, to be commercialized into a product with the need for improvement in the design of the joint parts, a management system is needed to increase the precision in the fabrication process.

• 에너지공학
• /
• 제22권2호
• /
• pp.83-89
• /
• 2013

에너지사용은 우리생활과 밀접한 관계성을 유지하고 있다. 사계절이 뚜렷한 우리나라로서는 건물분야에 냉,난방이 필수품처럼 여겨지는 세대에 살고있어 에너지 사용과 유지에 새로운 트렌드를 요구하고 있다. 이에따라 정부는 신축 및 기존건축물의 에너지효율 개선을 위해서 단열기준을 지속적으로 강화하여 에너지절감을 꾀하고 있다. 공동주택의 에너지효율 분석중 가장 중요한 요소가 열관류율이며 그값은 외피면적비에 대한 창면적비에 따라 난방에너지 요구량이 큰차이를 보여주고 있다. 그러므로 지속적인 효율개선 정책과 외피면적에 대한 창면적비의 규제가 필요한 시점이라 생각한다.

• 대한화장품학회지
• /
• 제30권1호
• /
• pp.123-128
• /
• 2004

최근 기능성 화장품의 대두로 새로운 형태의 미백제들이 많이 출시되고 있다. 본 연구에서는 천화분근, 하고초엽, 위령선근을 이용하여 새로운 미백제를 개발하였다. 그러나 이러한 미백제는 용해성이 좋지 않고 빛, 열, 산소에 의하여 변색 및 함량의 변화를 가져온다. 먼저 천화분근, 하고초엽, 위령선근을 10배수의 50％ 에탄올을 넣어 75∼85도에서 6∼8시간 추출한 후 여과, 농축, 건조하였다. 건조된 추출물을 이용하여 티로시나제 효소 활성 억제효과, 마우스의 색소세포를 이용한 Bl6 멜라닌 생성 억제 효과, brown guinea pig의 동물 피부의 미백효과 결과 다른 비교 샘플에 비하여 매우 우수한 결과가 나왔다. 또한 천화분근, 하고초엽, 위령선근을 안정화시키기 위해서 propylene glycol (PG)/hydrogenated lecithin/middle chain triglycerides (MCT)/glycerin/water를 고압균질화기를 이용하여 30∼50 nm인 리포좀을 만들었다. 이러한 리포좀은 기존의 처리되지 않은 추출물에 비하여 빛과 열에 3∼5배 안정성을 보였다. 이러한 실험을 위하여 particle size analyzer, freeze fracture transmission electron microscopy (FF-TEM), chromameter, HPLC의 분석장비를 사용하였다.

• 한국재난정보학회 논문집
• /
• 제7권4호
• /
• pp.286-293
• /
• 2011

최근 건축구조물은 초고층화, 대형화에 따라 고강도 및 고성능콘크리트의 사용이 증가하고 있는데, 고성능콘크리트는 화재 시 발생하는 폭렬현상에 취약한 문제가 있다. 폭렬은 화재 시 콘크리트 피복의 손실을 초래하여 내부콘크리트와 철근의 열전달률(rate of heat transmission)을 높여 콘크리트와 철근의 온도를 상승시키는 작용을 한다. 이러한 고강도콘크리트의 화재 시 폭렬을 막기 위하여 여러 가지 연구들이 진행되고 있으며 대표적으로 폴리프로필렌(Polypropylene)섬유, 강섬유를 사용한 연구들이 폭렬제어성능을 입증되었으나 유동성 저하에 따른 시공성 문제점이 제기되고 있다. 그러므로 본 연구에서는 위와 같은 문제를 에스테르계 윤활제 및 비이온성 계면활성제를 포함한 코팅액으로 코팅된 polyamide 섬유를 혼입하여 내화성능을 확보하였으며 강도영역별 최적 조건을 실험을 통하여 도출하였다. 13mm의 polyamide 섬유 적용시 강도영역별 적정 섬유 혼입량은 160MPa는 2.5kg이상에서 폭렬제어가 가능할 것으로 사료된다.

• 열처리공학회지
• /
• 제22권6호
• /
• pp.345-353
• /
• 2009

The precipitates of $L2_1$-type $Ni_2AlHf$ phase in B2-ordered NiAl system has been observed by using transmission electron microscope (TEM). The hardness of as-quenched NiAl-Hf alloys is high due to the larger strengthening. However, age hardening of this alloy is not main effect to increase hardness compared to the large microstructural variations during aging. At the beginning of aging, the $L2_1$-type $Ni_2AlHf$ precipitates keep a lattice coherency with the NiAl matrix. The orientation relationship between the $Ni_2 AlHf$ precipitate and the NiAl matrix is <100>$_{Ni2AlHf}$//<100>$_{NiAl}$, {001}$_{Ni2AlHf}$//{001}$_{NiAl}$. By aging treatment for long time $Ni_2AlHf$ precipitates lost their coherency and change their morphology to the spherical ones surrounded by misfit dislocations. The orientation relationship between the NiAl matrix and the $Ni_2AlHf$ precipitates, however, has been kept even after longer aging time. The lattice misfit between the $Ni_2AlHf$ precipitate and the NiAl matrix has been calculated by the selected electron diffraction patterns, and the spacings of misfit dislocations is about 4.5% at 1173 K.