• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.17-18
• /
• 2007

Solid oxide fuel cells are clean, pollution-free technology for the electrochemical generation of electricity at high efficiency. Specially, the polarization resistance between electrolyte and electrode of SOFC unit cell is of importance, because it is desirable to develop SOFC operating at intermediate temperature below $800^{\circ}C$. The LSCF cathode prepared using modified oxalate method was investigated with different electrolyte. A precursor was prepared with oxalic acid, ethanol and $NH_4OH$ solution. The LSCF precursor was prepared at $80^{\circ}C$, and pH control was 2, 6, 8, 9 and 10. The precursor powder was calcined at $800^{\circ}C$, $1000^{\circ}C$ and $1200^{\circ}C$ for 4hrs. The crystal of LSCF powders show single phase at pH 2, 6, 8 and 9, and the average particle size was about $3{\mu}m$. The LSCF cathode with heat treatment at $1200^{\circ}C$ showed a plot of electric conductivity versus temperature. Unit cell prepared from the LSCF cathode, buffer layer between cathode and electrolyte and the LSGM, YSZ, ScSZ and CeSZ electrolyte. Also interface reaction between LSCF, buffer layer and electrolyte were measured by EPMA and the polarization resistance for unit cell with cycle measure using a Solatron 1260 analyzer.

• Journal of The Korean Association For Science Education
• /
• v.13 no.1
• /
• pp.92-99
• /
• 1993

The purpose of this study was to investigate and analyze the conception of elementary school students on evaporation and condensation, and then to verify the types of the conception. Forty-eight children from six elementary schools were sampled by stratified random sampling in Seoul and other provinces. They responded to the questionaire and the interview. This study was carried out according to the process of the basic study, the preliminary study, and the main study. The materials collected were classified and analyzed according to the types of children's ideas. The findings of this study were as follows. 1. The vocabulary used to describe the evaporation phenomena varied according to the situations, and the scientific term "evaporation" was more frequently used by the older groups. 2. Most children answered that the last location of water were air/sky/cloud. Air/cloud which represents the scientific conception of the location of water were mentioned by children of all ages. The higher the grade of the children were, the more scientific conception the children mentioned, however. 3. Most children referred to the heat as the factor of evaporation. Wind, on the other hand was mentioned by less than 10% of lower graders, and by about 30% of higher graders. 4. The result of asking children whether they thought it was possible to get the evaporated water back showed that about 70% of lower graders denied the possibility of the water being reversible. About 60% of higher graders. however, recognized that the water will be returned as rain or condensation. This increase may be associated with formal teaching of water cycle. 5. In the ideas of evaporation and condensation, some of the children have supernatural ideas and animism, which are most younger chilren's characteristics.

• Korean Journal of Human Ecology
• /
• v.24 no.2
• /
• pp.297-325
• /
• 2015

The purpose of this research is to analyze content elements of Housing area in 2013 middle school Technology Home Economics textbooks 1 and 2, total of 22 according to 2009 revised curriculum. The analysis method was content analysis, focusing on contents of main text, tables & figures, reading material, and activity materials by their content elements. This research will contribute in obtaining suggestion for the post curriculum/textbook development and helping teachers to perform a lesson. The results are as follows. First, Housing area included 1 to 4 content elements per each units, from 2 chapters and 6 units. The content elements stated in Home economics curriculum were total of 16 which consists of 'the meaning of housing,' 'housing types,' 'family forms,' 'family life style cycle,' 'life style,' 'neighboring environment,' 'co-living values,' 'air environment,' 'heat environment,' 'light environment,' 'acoustic environment,' 'space division,' 'circulation', 'effective use of space,' and 'sustainable dwelling practice.' All of these components are dealt with in every textbooks. Second, the numbers of content elements provided in each textbooks were the same, however they showed difference in their contextual aspect. Some contents need supplemental material for their lacking content element. Others need proper understanding of the concept because some showed different contents from the appropriate content elements. Third, repetitions in content elements were observed, the contents of 'co-living values' in textbook 1 and 'sustainable dwelling practice' in textbook 2 were similar in terms of eco-friendly housing, co-housing and universal housing. These two content elements should be merged as one next curriculum, or should be stated together in one subunit.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.845-853
• /
• 2000

The optimum cure cycle and carbonization condition were selected by the DSC and TGA analysis and green bodies were prepared by the method of hot press molding and then carbonized up to 140$0^{\circ}C$. Additives such as graphite powder, carbon black, milled carbon fiber and carbon fiber mat, which were considered to be effective in improving the interlaminar shear strength, were also added to check their effects on the density and porosity of products. Then, their relations with mechanical properties such as ILSS and flexural strength were investigated. The composites added 9 vol% of graphite powder showed the greatest values of ILSS and flexural strength. Otherwise, in case of adding carbon black, the composites showed the slight improvement of ILSS at its contents of 3 vol% but the flexural strength was decreased. When milled carbon fiber and carbon fiber mat were added, the lack of resin and the heat shrinkage during the carbonization caused the delamination, resulting in decreasing the density, ILSS and flexural strength.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.1
• /
• pp.49-54
• /
• 2010

Rotor pole for AC(alternating current) generator is manufactured through transfer warm forging die. As soon as the material is heated at the warm manufacturing process, it is transferred to the first stage for upsetting work and then to the second stage for lateral extrusion work. The processes at the lateral extrusion work such as die block, die bushing, center punch, and side punch make severe condition and abrasion which leads to shorten the die life. This causes production decrease, long maintenance time, and low level of precision. Research on the die material selection, heat process cycle improvement, electric discharge machining trouble solution, and re-construction of main parts is expected to find a method to lengthen the die life up to 40 - 50%.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.103-108
• /
• 2003

The effect of equivalence ratio and fuel/air mixing quality on the phase-resolved gas temperatures at different phases of the oscillating pressure cycle was experimentally investigated. An atmospheric pressure, optically accessible and laboratory-scale dump combustor operating on methane with heat release rate of 1.59kW was used. Temperature measurements were made using coherent anti-Stokes Raman spectroscopy (CARS) at several spatial locations for typical unstable combustion conditions. Analysis was conducted using parameters such as phase-resolved averaged temperature, normalized standard deviation and temperature probability distribution functions (PDFs). Also the probability on the occurrence of high temperature (over 1900K) was investigated to get the information on the perturbation of equivalence ratio and NOx emission characteristics. It was shown that most of temperature histograms exhibit Gaussian profile which has short breadth of temperature fluctuation at equivalence ratio of 0.6, while beta profile was predominant for the cases of other equivalence ratios (${\Phi}$=0.55, 0.50). The characteristics on the occurrence of high temperature also displayed periodic wave form which is very similar to the pressure signal. And the amplitude of this profile goes larger as the fuel/air mixing quality become poorer. These also provided additional information on the perturbation of equivalence ratio at flame as well as NOx emission characteristics.

• Journal of Energy Engineering
• /
• v.24 no.2
• /
• pp.72-78
• /
• 2015

In the present study, a recuperator to improve the thermal efficiency of a micro gas turbine is considered. The counter flow plate-fin heat exchanger with offset strip fins is chosen as the type of the recuperator. From the optimization study as varying design parameters of the recuperator determined from the ideal cycle analysis, the internal structure of the recuperator is determined. The recuperator is made from stainless steel 304. In order to evaluate performance of the recuperator, experimental investigation is performed. The effects of inlet temperature of hot-side of the recuperator on the thermal performance of the recuperator are investigated. As a result, effectiveness of the recuperator obtained from the experiments is well consistent with that obtained from the correlations.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.199-206
• /
• 2006

Automatic grease lubricator is equipment that provides adequate amount of fresh grease constantly to the shaft and the bearings of machines. It minimizes the friction heat and reduces the friction loss of machines to the least. This research is to develop automatic grease lubricator by gear driven mechanism with controlled operation time. The ultimate design of this equipment is to lubricate an adequate amount of grease by a simple switch clicking according to the advanced set cycle. The backlash of the gear was minimized to increase the output power. To increase the power of gear mechanism, the binding frequency and the thickness of the coil were changed. To control the rotating cycles of the main shaft according to its set numbers, different resistance and chips were used to design the circuit to controls electrical signals with pulse. The body of the lubricator was analyzed by stress analysis with different constructed angle. The stress analysis for differing loading pressures applied to the exterior body of grease lubricator due to the setup angle, was found that the maximum stress was distributed over the outlet part where the grease lubricator suddenly narrowed contracts. Digital mock-up was analyzed and the rapid prototyping(RP) trial products were tested with PCB circuit and grease. The evaluation of the outlet capacity for RP trial products was conducted, because the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, the finishing process was applied to decrease the roughness of the surface to a comparable level and was able to test the performance examination for the product.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.4-4
• /
• 2009

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) was welded through a combination of a diode laser and CNC. Laser beam passed the transparent PC and was absorbed in an opaque ABS. Polymers were melted and welded by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead size and the specimen cross-section were analyzed, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was 3.75mm and the shear strength was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in CNC machining processes, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision. By combining two operations processes developed process gained 50% more efficiency.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.814-821
• /
• 1999

The specific capacitance characteristics of the electric double layer capacitors(ELDC) which were made of phenol based activated carbon fiber(ACF) electrodes. Also the effect of aqueous electrolytes on the cell performance has been investigated with respect to different specific surface areas of electrodes and different kinds of aqueous electrolytes. It has been shown that larger surface area and pore size, higher conductivity of electrodes, and higher ion mobility of electrolytes have better specific capacitances. It has been found that heat treatment at $1200^{\circ}C$ and $CO_2$ post-activation at $900^{\circ}C$ of the electrode are effective to improve the specific capacitance over 145F/g and 165F/g, respectively. The EDLC showed high efficiency and long cycle life over 30000 cycles.